chattering like that is usually a supply issue. Meaning the main pump isn't getting enough oil Either because you have leaks after the main pump And that oil isn't getting back to the charge circuit Or your transmission pump is not getting the oil to the main pump Because of a dirty sump screen or filters screen or filters or or it's getting worn out or you have internal leaks After the main pump anything leaking will usually get hot pretty quick There is a plug just to the right of your top link On the back of the transmission case mission case it takes a 1/2 inch square drive, If you take that plug out and start the tractor up do you have yeah it's practical up do you have oil spraying around in there or oil is air or oil running from the top down
@@jonstevensmaplegrovefarms3754 I will have to check that. One thing I have noticed is the right scv will get hotter that the left one. I don’t have any chattering in the three point with I lift it just some chattering the in loader when I left it at 1500 rpms or more. When using the loader at 1300 rpms it operates completely smooth so I believe I have a hi press lk after the pump. What are you thoughts sir?
Take a picture before they fall out of place. LOL it should be opposite of the other side as far as where that flat portion is. 4640jon@gmail.com send me an email I'll see if I can't find a picture somewhere
Lol yeah one slid before could get pic.i knew how one went and had faint mark where it had been bolted down before...or atleast i hope i seen what i think i did lol guess ill know if doesnt work right?!
Good videos. I have to work my SVCs over on my 2840 both are passing pressure.
Yeah I have had the pressure poppet leak and implements drift up. I have put seals in them but my neutral is too tight! Thanks for the demonstration!
That was great, I'm all set to try it on the 4450. Thanks Jon!
A lot of good info!
Thanks for all the knowledge!
Thank you
I would like to do a lot more of these in the future.
Good to have parts 👍
Thanks brother. I have a feeling my 4440 scv is bypassing. My loader will shake until I move the right remote to float
chattering like that is usually a supply issue.
Meaning the main pump isn't getting enough oil Either because you have leaks after the main pump And that oil isn't getting back to the charge circuit Or your transmission pump is not getting the oil to the main pump Because of a dirty sump screen or filters screen or filters or or it's getting worn out or you have internal leaks
After the main pump anything leaking will usually get hot pretty quick
There is a plug just to the right of your top link On the back of the transmission case mission case it takes a 1/2 inch square drive, If you take that plug out and start the tractor up do you have yeah it's practical up do you have oil spraying around in there or oil is air or oil running from the top down
@@jonstevensmaplegrovefarms3754 I will have to check that. One thing I have noticed is the right scv will get hotter that the left one. I don’t have any chattering in the three point with I lift it just some chattering the in loader when I left it at 1500 rpms or more. When using the loader at 1300 rpms it operates completely smooth so I believe I have a hi press lk after the pump. What are you thoughts sir?
How do you know which side the angle end of cams go?
One of cams slid down and not sure if it was like the other one or the opposite
Take a picture before they fall out of place. LOL it should be opposite of the other side as far as where that flat portion is. 4640jon@gmail.com send me an email I'll see if I can't find a picture somewhere
Lol yeah one slid before could get pic.i knew how one went and had faint mark where it had been bolted down before...or atleast i hope i seen what i think i did lol guess ill know if doesnt work right?!
Hello can you give me the part number of kit Thanks
Kit for the valves is "RE10924"
For the coupler kit "RE66985"
para verla en español
To see her who in spanish?
a guy is a living person not a hydraulic valve its part of a machine