🛠Charlie DIYte Amazon Tool Store amzn.to/3fcLnY4 - all my tried, tested and much loved DIY tools. Help support me on Patreon -www.patreon.com/charlieDIYte (includes Discord access).
Best caulking demo ever!! Thank you so much - this was so helpful! The fact that you took the time to explain how the standard techniques could cause problems, and you even showed close-ups - to me, that made all the difference & convinced me your way is the best way. I appreciate you sharing this. Thanks again!!👍💗✌️
As a professional builder for over years, This is one of the best explanation videos I have ever seen on the subject. Thank you so much for the time you have put into this and thank you so much for the quality content, you rock!
Thanks so much mate, I always think it speaks volumes when a professional builder is humble enough to tell me I'm doing something right. 😉 Shows you're still hungry to learn and therefore that you're clearly very good at your job (after all, we never stop learning)!! Take a look at this one if you've got a moment as I didn't tackle corners properly in the vid you've watched, but clearly it's not always practical for you guys to wait for a joint to set before finishing it. Thanks again 👊 ua-cam.com/video/EErbuodMOAM/v-deo.htmlsi=OMqy7xUv2Mvcx8vp
Wish I'd seen this years ago! Just about to do my shower tray. I did buy the tape to go around, but it didn't work. VERY good explanation. I've always used detergent and my finger, with the results you described. I'll now buy the tool recommended. Fingers crossed! Thanks again
The painters tape caulking trick never worked for me n i used to sit n cry n redo it again n again for two decades. Finally a person who shows the same flaws in the technique which i experienced. Thank you
One of the most crystal clear presentations I've ever seen on any topic on YT. The first seven minutes, explicating in meticulous detail how NOT to apply silicone, is invaluable. (I have for years followed as standard practice almost every single one of these DONT's.) I am a professional finish carpenter, with a keen interest of late in improving my caulking game. This video delivered more useful content, accompanied by an incredible degree of logical explanation of underlying principles, than I could have imagined exists. Thank you!
Thanks so much Michael, I really appreciate that. As I always say, a professional tradesman who is still receptive to learning new skills or challenging what he's learnt over the years is clearly very good say his job 👏 If you have a moment just check out this video too ua-cam.com/video/EErbuodMOAM/v-deo.html as I didn't cover corners very well in the one you've watched.
Crystal clear presentation?? WTF? Folks making caulking how to videos and making up their own bullshit nonsense. I was in real caulker for many years and none of these utube videos are anything even close to “ pro “ actually he’d be fired so fast just like So many others. I worked for one guy who already Fired 12 Mostly Real Caulkers who all of which were way more skilled and knowledgeable than this wanker
As a girl who has never DIY'ed anything in her life, let me say, this video was amazing. As someone else said, who knew a 20-minute video on silicone could be interesting! You really do make it interesting and easy to understand, though. I now feel ready to redo my landlord's awful silicone job. Many thanks, sir!
Aw, thanks so much for that! One thing, if you've got any vertical sections to do/ corners, check out this video too, if you haven't already ua-cam.com/video/EErbuodMOAM/v-deo.html 👍
@S. O. You posted your comment 2 years ago about redoing your landlord’s awful silicone / caulking job, so maybe you can’t answer this, but do you remember how you removed the caulking? Did you just cut it with a razor? If you recall how difficult the removal process was, please let me know!
@@CharlieDIYte sick and tired of seeing people using the tool the wrong way round and this fekin spray,,, as you've pointed out quite clearly the soapy spray goes behind the silicone, as an engineer and Builder now in my 50s, when this tool first came out many years ago the rep described the silicone tool as the ultimate tool for silicone and you must use a soap spray, and I am probably 80% certain he used the tool chamfered going against the silicone, then many years later on another job seeing this guy using one of these tools, no spray and the sharnford Edge behind the flow of Direction, as in the video,,,,, yep we've all used fingers and tape, and to think back in the day we used to lick our finger and run it over the silicone then again and run it over the silicone,, dow Corning silicone in Barry South Wales, fabrication company I worked for at the time we did a job inside there, pesticide fungicide and chemicals that went into the silicon, the industrial silicone mice likes the stuff apparently hence the pesticide, I told this guy i used to lick the silicone for smoothness he said I'm surprised I've not got an extra toe growing,, good video man... Dave
14 years I've been a Floor Layer and I've always hated siliconing. I came across your channel when trying to find the right drill and this came up in my suggested yesterday. I tried this technique today and its so much easier with such a professional finish. For any tradesmen reading, you get a lot of waste as Charlie shows but you just need to add the cost onto the job. Nothing worse than a decent looking vinyl or luxury vinyl tile job and poor sealant finish. Thank you so much for this great demo, and if you haven't already, I would highly recommend subscribing to this awesome channel 😊
Aw, thanks so much John, I really appreciate that. As you say, you do get waste by virtue of the way it works but don't forget the waste was amplified in my case because I was applying such a wide bead, and if the waste upsets people, as long as they're quick, they can tool it into the next run before smoothing with the tool. Plus the bead is so much stronger so you're doing your clients a massive favour, particularly on a floor that they'll be cleaning often. I always think a tradesman who is prepared to embrace new techniques (ie prepared to innovate) is clearly very good at their job 👍 Thanks again.
Holy cow this is a game changer! I've just done the bathroom in about an hour with no swearing or covering myself/the room/kids/dog/wife in sealer. Thank you
I’ve worked in construction for 30 years and what i love about this video is the open mindedness to question supposed tried and tested methods like the fairy liquid in a bottle. UA-cam is such a great resource
Thanks so much Steven. Can I throw that back at you and say that anyone who has worked in the industry as long as you but who is still receptive to new ideas/ processes is clearly good at what they do👏 If that guy hadn't trolled me I'd probably never have done this video but I was so perplexed at how the soap bottle brigade had got away with this for so long I felt something had to be done about it.. Thanks again!
Hi Charlie, i’ve been a homeowner for 35 years and I’ve made every caulking mistake possible. With your help, I now have the knowhow and skills to create a waterproof and good looking caulk seal. As a science fan, I appreciate the cutaway view of what’s happening. I also appreciate how you have put aside convention (45° tip) for what you know to be true! Thank you 1000x!!!
Thank you for this tutorial Charlie. I followed your instructions to the nth degree and everything slotted into place. I’m 76 years old and I’ve been a DIY enthusiast for most of my life. I’ve lost count of the number of bathrooms I’ve refurbished and never as Silicone been so uncomplicated and easy to apply. You are amazing! Thank you.
Kenneth, thank you so much for your wonderful comment! I'm so chuffed it worked so well, which of course it would as you implemented it so meticulously! You've probably already seen it, but for future reference I also have a corners video ua-cam.com/video/EErbuodMOAM/v-deo.html Thanks again 👍🏻
I know this is an old video but being a pretty naff diy'r, you have inspired me to seal my own bathroom...being 41 and scared to make a mess I watched this, subscribed to your channel and did my bathroom...thanks mate, truly, thank you
I just wanted to thank you for this video, I'd been putting off resiliconing a shower tray that had a slight leak but watching this allowed me to approach the job with a plan and do it correctly.
I have just done the nearest thing to a perfect seal that I've ever done in my life. Why did I not find this guide and this tool 40 years ago? Absolutely brilliant!
If I had a company, I'd hire you as the VP of Quality! I love the attention to detail and the power of keen observation! Thank you for taking the time to educate all of us.
I like that you go with what you know works with reasoning to back it up.. Many tradesmen are taught the one way and never consider there could be a better technique. Peer pressure/ridicule among onsite colleagues ensure they never try a different method. Keep up the good videos.
That's exactly right, Joey, but the really good tradesmen are the ones who have commented on here that they've watched this technique and realised they've been doing it won't all these years. Someone who is receptive to new techniques is, I think, clearly conscientious and good at his job!
I've just done my bath following your instructions and I'm delighted. A more clumsy and hapless individual than me would be difficult to find, so it was a bit traumatic and there was as much silicone on me as on the bath, but it looks good and strong. We did it the "traditional" way last time and everything that you said could go wrong, did go wrong. So thank you Charlie (and hubby can do it the next time).
Yup, this is the best video on this subject by far. So many videos on youtube repeating things without any explanation, like “cut your nozzle at 45 degree angle - just because...” Never made sense to me, when a 90 degree angle is much easier to work with. And the soapy water spray always fucks up my silicone beads.
This is a really great, no BS, plain English explanation and demonstration of what I've been doing wrong but didn't really understand 'why'! Just Ordered the Cramer tool - omg they're so good; my 'grouter's-sealant finger' was delighted! Thank you so much for this Charlie; massive shout-out.
You're very welcome Jules. The Cramer tool is awesome isn't it. Check out my corners video too ua-cam.com/video/EErbuodMOAM/v-deo.html if you've got a moment as I didn't really cover corners in the vid you've watched. 👍
Absolutely, it drives me insane when the host of a tutorial video gives instructions but doesn’t tell you WHY something needs to be done. It leaves you in the crappiest position for troubleshooting.
Cheers mate, really appreciate the comment. So chuffed you nailed it. For corners check out this vid ua-cam.com/video/EErbuodMOAM/v-deo.htmlsi=I5IY3FNcqOe5vxYZ as I didn't cover corners properly in the original vid. 👊
This was amazing - I made a proper stuff up of my bathroom about a year ago (it looked alright, but the silicon lifted quite quickly after applying). I watched this video before doing it last week, and went out and made sure I was properly prepared this time. Thank you so much for making this freely available - you're helping millions of people (by the view count), and I hope your business is blessed and booming.
So glad to hear that, Tim. Did you see my corners vid too ua-cam.com/video/EErbuodMOAM/v-deo.html (in case you've got any other siliconing to do). Business is fine thanks. It's never as easy as it looks to make money from this, which is why I've set up my Buy me a Coffee channel now I'm doing this full time, but I'll get there in the end 👍🏻
Aw, thanks Siva. I'm blown away by that. If you're planning a silicone project check this video out ua-cam.com/video/EErbuodMOAM/v-deo.html as I didn't mention corners in the one you've watched. 👍
I just did my GF'S Landlords shower following your methods step by step, and it's turned out amazing. Some of the tile joints were over 10mm away from the shower tray, and some touching it, uneven tiles, the lot. I've probably done something like this about ten times in my 48 years (for myself) and it's never been close to looking as good as this. Many thanks for making this video Charlie.
Wow- I've been remodeling homes for over 40 years, and thought I knew how to caulk. This video took my scale to a whole new level. Bravo, Charlie! Now I'm going to have to look at your other videos and see what else I need to learn from you?!
Great video, I'm a DIYer and have been using the Fuji tools for a few years now, but still learnt a couple of things from your video. One tip I have, if you have the luxury of time, is never to do both sides of a corner on the same day. I do one side and then come back next day and do the other side after the first side has dried. Gives a perfect mitre joint. Maybe need 3 days for a 3-way joint.
I used this product and method. I am a trained carpenter so this is proper respect. Like everything it takes practice. I was massively impressed. I have a near perfect finish. I love the way you can work and rework. I have a couple of niggling criticisms maybe with the descriptions but minor over all massive thumbs up . Less cooks makes a better broth
Thanks David, I appreciate that. Yes I accept it wasn't perfect, and I omitted corners, which you can find in this video bit.ly/3c7SKio but overall it gets the hedge across. Really pleased it worked for you. It's no surprise to me that you were receptive to a new way of doing things - the hallmark of a good carpenter 👍🏻
@@CharlieDIYte So many folk can barely read instructions, let alone listen to someone trying to teach them a different way of doing things. It affects the industry and consumer detrimentally and QOL in the UK somewhat. My uncle designed a bathroom for Phil Collins down in Brighton so maybe thats where I get my difference from :)
Brilliant pro video, I've been building and fitting out houses for 40 years and although I thought I was pretty good I got several points from this that I'd never considered! Thanks for spending the time to do a great demo.
What a pleasure to watch - a breath of fresh air. Loads of common sense, and lots of received wisdom challenged clearly and eloquently. Who says a 20 minute video on applying silicone can't be interesting!
I have to say I consider myself a seasoned siliconist. After watching this video I am forced to rethink my self taught methods. I really take it as a positive though, so thanks for showing me where I may have been doing things incorrectly, and pointing me in the right direction. This really is a useful video. I know there are trades out there that will argue tooth and nail that their method is best, but you cant really argue with the detailed information in this video. In my humble opinion this is pure gold. Thanks Charlie
Have never used silicone in my life, my boyfriend attempted to silicone our bathroom a few months ago and did an awful job, so thought I’d do my research and show him I can do a better job! 😂 this video was amazing, I was about to just go for it and use my finger to smooth it out but quickly learnt from this vid, that this isn’t the way. My boyfriend came home and didn’t believe I’d done such a good job, so thank you so much 😁
Brilliant video thanks! I have bought the FUGI kit and it is great tool for the job. My only issue is I have quite an old house where lots of the angles of tiles etc that have previously been laid are not square to the wall, so the 90 degree FUGI tool would not sit in the joint. Gaps would appear as I would drag the tool along. I got around this by actually making my own tool from a credit card for these awkward places that the FUGI could not reach.
You can angle the tool slightly so a 90° tool it fits into an other than 90° edge to a wall. The similar tools I got from eBay have some angles greater than 90° and some less but all can be used on a 90° corner by angling and keeping both bottom and wall edges flat against the tool edges. The same would apply if the wall leans out or in although its probably best to have the tool at 90° to both bottom and side ideally.
Charlie, you're right. This is just about the opposite of what I've seen and learned and you explained why some of my project came out less than beautiful. Never realized how useful the silicone caulking tools are. Used to always use my finger. I'll be purchasing a set soon. Thanks.
Sir, I thank you VERY MUCH. Your tip to do the verticals first and to not spray with soap until the silicone seals everything it's supposed to was invaluable. I had the entire bathroom and toilet sealed wrong by the contractor, floor to ceiling. I spent 3 days removing all of that with countless razors and scrapers, in the end resorting to Knauf solvent remover for that perfect 'never touched by silicone' finish. Now I have to do it right and some trials showed me you taught us all well.
Hi Charlie, I just wanted to express my appreciation for this video and how helpful it’s been for a newbie to siliconing like me. I followed your dos and donts and the job got done with a much better result than I expected. I have now been able to re-silicone my shower tray and the bathtub. Thanks so much! My next project will be re-caulking my wooden window panes 💪🏻😃
Nice one Charlie, have been ‘caulking’ for years; watched your vid and purchased the 7 kit, what a game changer, brilliant results. So easy, working in short sections, first caulking job I have ever finished without swearing or going around the house shutting doors. Thanks Charlie, well done mate 👍🏼👍🏼👍🏼
Charlie: I thought I am a very competent DIY'er with many years of house building/renovation behind me. I am also Architecturally trained and so have an eye for details (poor siliconing has always bugged me y contractors). I just wanted to thank you for your informative video. I thought I always did a good siliconing job but after trying the Cramer kit (from your recommendation) I will for one NEVER go back to taping or using washing up liquids. I cant believe how such a simple set of tools does such an impressive/fast and neat job. All fillet depths are catered for and the semi flexible rubber tools allow total pick up of any overspill. The secret if there is one is to clean off the tool frequently every foot or so. If the silicone does snag (as some makes of silicone skin unbelievably fast) or there is a dip just fill again and go over. Thank you so much ! The best 20mins of my DIY life and £14 I have ever spent_All power to you for showing this so well. Anyone who promotes washing up liquid or a finger is a total hack. And now I can prove it. This knowledge is also now going on site with me, so sloppy mis-informed contractors beware !
This guy has to be one of the best on UA-cam. Very detailed step by step explanation & backs it up with a demonstration so how can you fault him? Thank you for taking the time to share your valuable skills.
You're very welcome, Harry. Thanks for the comment. Take a look at my corners video if you have a moment ua-cam.com/video/EErbuodMOAM/v-deo.html as I didn't really cover corners properly in this video 👍
Charlie. I am a professional bodger - if it can go wrong, it does. My shower and main bath were in desperate need of re-sealing and I was dreading the cursing and frustration that would inevitably lead to a shoddy result. Having found your video, I saw a glimmer of hope - could I possibly undertake the work without pain and end up with a decent finish? Well, yes and yes - I'm delighted. The only thing I would do differently would be to buy a silicone kit with the transverse joint attachment - mine didn't have this. Having subscribed and looked at some of your other videos, I am feeling confident at tackling more jobs around the house. Many thanks and keep up this great work. Adrian
Adrian Jarratt Hi Adrian. Thanks so much for taking the time to tell me how you got on - comments like yours are what inspires me to keep producing these videos! Absolutely delighted that you pulled out off! If you can silicone successfully the world of DIY is your oyster my friend! As my video has hopefully shown you the bodging had less to do with your ability and more with the preparation and application! Keep up the good work and many thanks for subscribing!
Genius, have just siliconed new bathroom using all the 'do not' use methods and, already experiencing the issues shown. Wish I had found this video first. Now going to redo and, use this video as my master guide, great work.
OMG! WHAT?? You are the most perfect example of what all the repairmen & carpenters etc keep constantly referring to as the "Retards that keep them in business"! All these dumbest humans in history, the dumbest humans possible that watch a home improvement show & try to do things themselves, completely mess it up & have to call a pro to fix it. & HOW can you have messed it up anyway when EVERYONE I know was "born" with Common-sense & will tell you that Silicone is the EASIEST thing u could possibly use! I mean HOW can you not even use "Glue", & not just any glue but "Rubber" based glue which is the Easiest possible, there is Only "3" steps that NOBODY should have to read instructions to know either, 1, make sure the surface is fairly clean (Which barely matters as Ive siliconed Many things that have been dirty, covered in sawdust or even "wet" when using most bathroom or plumbing silicone that clearly says it works on wet surfaces) 2, it literally just squirts out onto the surface & 3, smooth it out usually just with you finger! So HOW the hell could you FAIL at that? You realize its literally a well known fact that anyone with half a brain & common sense will tell you that its HARDER to brush your teeth than it is to use Silicone. I mean stupid, you just commented & used the word "Genius" for a video on HOW TO USE GLUE!! & the easiest glue in the world at that! Ive used silicone since I was 13 & its literally IMPOSSIBLE to mess it up! Its just Rubber based glue, thats it, & even easier than other glues it wont sudden;y dry on you fingers etc so u have ages to wipe it off & even plumbers & carpenters etc just use their fingers to spread it. WHAT is there to possible mess up? There is NO way the single dumbest humans in existence should ever be allowed to breed, Im TERRIFIED to think that you may have kids, people this insane & incredibly stupid should NEVER be allowed to breed, I mean if u cant use Rubber glue theres NO way you could ever drive a car, feed your children, I mean if u cant use silicone then u wouldnt be able to even brush you teeth, HOW is it even possible for supposed "humans" like you even exist? When humans are "Born" with Common-sense, Im not joking or exagerating when I say I dont think someone this dumb could even come close to being called a "human", Im TERRIFIED for my kids & Every single other child out there to know people out there as braindead or retarded as you exist.
@@VirusOfCyrus Your comments say more about you than about anyone else. Very aptly named - "Virus". By including your friends in your rant, you are also insulting them. Pity you have so much time on your hands to attempt to insult others, than doing something useful with your own life.
Watched this again earlier today as I had another bathroom to do. It really helped me. I have to say I was very pleased with the tips about cutting the nozzle straight rather than at 45% and also cutting the nozzle at the same measurement as the tool you use to finish. Very good tips and I was able to do a real good job of my mastic thanks to this video - nice one.
Thanks Bill, really glad you found it useful. There's also this one bit.ly/3c7SKio for corners of you have a second, as I didn't cover corners particularly well in the vid you've seen. 👍🏻
I always enjoy watching your vids. Even though you did this 5 years ago, you always reply to questions. A class act. I'm the DIY'er in our house as my husband hasn't a clue! Been married almost 52 years. As he says, more than 3 life sentences. I have always liked to be able to "sort" things out. Keep up the good work.
These are just the best DIY videos I’ve ever watched. Charlie is a real quality guy and it shows in all the detail he goes to as he explains what to do. I also like the fact that he’s open and prepared to diss some old views on how to do things as he explains why with clear logic and demonstration. Top of the class to me.
Thanks so much David. Check out my corners video if you have a moment as I didn't really cover them properly in this one ua-cam.com/video/EErbuodMOAM/v-deo.html
Just watched your video again now that I wanted to renew my shower cubicle tray sealant which had been installed by a professional 6 yrs ago. I have always hated doing sealant repairs as in your video there are lots of ways suggested by people. I purchased the Cramer 7 kit which comes with the removal tool and blades---what a worthwhile buy, used the tool with one of the sharp blades(not the grout one) honestly it just sliced through the old sealant and then cleaned up any remaining bits. The blade point and angle is just ideal and if used carefully does not damage the tray. I followed your advice about the sealant gun nozzle width(the gap between the shower tray and shower wall was really small) so using the 10 mm blue tool(a similar gap to the old I removed) I successfully finished it off and only needed 2 passes and although it does waste some sealant I was amazed at the finish, there was a small bit near one end that had a slight mark but decided not to tamper with it ! The Video and the kit has mad me more confident to deal with sealant jobs in the future. I have watched several of your videos over the years and find them clear and concise and very informative.
Resealed the bath today, after watching this video a couple of times and buying a Fugi tool. WOW ! Can't believe how good it looks, amazing. Never thought I'd ever get to do it like the pro's, but seriously impressed with the results.Can't wait to do another one. Cheers Charlie!
Best advice ever, i have just re sealed my shower / bath and it looks amazing, never thought i'd ever get such a finish. lot of nonsense advice on YoutUbe BUT NOT this video, thumbs up
OMG... Your comment has made me TERRIFIED! Like I so scared for all the children in thew world knowing that there are "somehow" actually humans like you out there that actually werent born with "Common-Sense"! U didnt know how to use Silicone?!? That shouldnt be possible, its literally the EASIEST thing you can do in life besides breathing, its 200% easier than brushing your teeth (this is NO sarcasm or exaggeration at all either) There is literally "3" steps, make sure the surface is clean enough & isnt oily (it doesnt even have to be very clean or dry either, Ive used silicone on very dirty surfaces b4 or Subwoofer boxes with quite a lot of saw dust & it doesnt matter) then it literally just squirts out & u smooth it off usually with you finger, THATS IT! HOW can u mess that up or not know how to do it? I was 14 when I first used Silicone & I didnt even need to read they instructions, all I read was what ANYONE with half a brain would which is the drying time, Silicone is literally Rubber based GLUE! You cant use glue?? Firstly if your this terrifyingly braindead then you should own ANYTHING to even put silicone on! You wouldnt be able to drive a car or put a seat-belt on, this video is the single most pointless video in history, it should not need to exist as NOBODY should be even half this dumb, anyone that cant use a rubbery glue certainly should NEVER be allowed to breed, I cant imagine how terrifying it is to think people that somehow needed to watch this video could be allowed to have children! Those poor kids! They will never be able to listen to or learn a single thing from their father or mother or whoever it is that is too dumb to use glue. People this dumb shouldnt exist & Im VERY angry that you exist in my world when you dont deserve to, Common-sense is a "human" trait that ALL humans are "Born" with ok? This literally makes you not even human, do u think maybe your mum aborted you & u just never noticed??
Also, WTF do you mean "Like Everyone Else"?? Ive NEVER met ANYONE in my life & never will (besides u & other not even human morons that insanely need to watch the worlds dumbest & most pointless video on "how to use fu*king GLUE!") that couldnt use Silicone! How dare you imply that "Everyone" is this braindead!? I couldnt be more insulted for you to think All my friends & myself are literally the dumbest people in history, like me they dont even know you & your already giving them the biggest insult of their lives?? EVERYONE I know, including my 80 year old grandmother can use Rubber based GLUE without needing to be told how to, just like (Apparently UNLIKE You) they can wipe their own asses & brush their teeth without needing to be shown. Also, you should NEVER be using Silicone or ANY Glue based product, I cant think of ANYTHING I could be confisent that you could use as literally EVERYTHING in this universe is harder to use than Silicone, AKA the easiest thing in the world, so NEVER insult everyone else because stupidly (what a surprise, u had another stupid thought) think they are the most braindead life form in the world. Retard, wtf.
First of all, I am so happy I got trolled, this is the first time I ever got trolled by a real-life internet troll! I have to reply to it. So here goes Mr. Troll. Well, most people who do not work with or handle Silicone-based products and/or glue do not really know what they are doing. they believe glue = stick it on item 1 and attach to item 2, wait for two minutes and its done. This is the common sense you must mean to. Using silicone for the prevention of water/moisture into cracks in bathtubs can prevent a lot of monetary loss on account of having to suffer from water damage across your home. I believe you are not a homeowner, as you said, you have been doing silicone since you were 14 - what the hell? you mean you've been working at house renewal since you were 14? I was programming in basic, C, connecting Telnet and BBSs by the time I was 14. Since then I've been pretty good and I still believe that - yes, using Silicone is not a standard operation. When I came across the need in my house to repair the bathtub - I watched an experienced plumber placing the silicone as you said using your thumb and voila, looks like it worked. WRONG. three months later, there was leakage from that exact area. I decided upon myself to perform this simple task as you said, myself. So I bought silicon and was just about to do it as he did when I thought to myself: " Wait, if the expert guy used his skills and Magic Thumb and couldn't get it right, why should I think I know any better?" so I decided to research myself the best way and came across this amazingly good video which showed that using your thumb isn't really the BEST option when it comes down to stopping moisture and water from getting in through your sealing. I hope you saw this video, saw the error in your ways and learned how to seal with silicone in a better and more efficient way - so your customers (and I believe you are still doing this since you've been doing this since you were 14 as you said) will appreciate your hard-worked labor. I would like to also tell you to have a good day, enjoy your life, and keep writing these kinds of comments throughout UA-cam, spreading love and joy to all who read you. This enlightens me and makes me very happy and actually, I even paused my work just to go to your comment and reply back. But, I digress, so, to summarize I think Silicone sealing of housing sanitary items such as bathtubs - should not just be done because its obvious how it should be, but whoever does it, should know the full effects it may have on the house and not just man-handle the silicone with a Thumb because its CommonSense. I wish you all the best of luck and instead of replying to the second comment, I'll just leave this comment here for you to read. Besides, I'm sure your 80-year-old grandmother will be very happy to know this is what came out of her grandchild. I hope you find the best method of silicone sealing you can and be the best silicone sealer there is. Last note, please check your grammar and spell check your comments - not all people have CommonSense to know that "u" means "you", because please remember, "B" "C" "R" and "U" are letters, not words. Edited: Will not be replying further, I'm too busy working..
@@VirusOfCyrus Congratulations on being so clever. I thought it was a very useful video because I grew up believing that the way to put silicon around the bath was to cut the nozzle small, drag it along the gap between bath and tiles and then use your finger to smooth it. Maybe with a bit of washing up liquid on your finger to stop it sticking. So I learned something even if you feel it was all really obvious.
Your video has been absolutely invaluable! Just re-siliconed our shower, in an almost identical way to what you did here. Bought myself a FUJI kit - wow, what a game changer! Actually enjoyed the whole process thanks to you. No more dragging silicone or concave joints for me! Thank you so much!
Thanks so much for letting me know. So chuffed you aced it. And did you watch this one too do the corners ua-cam.com/video/EErbuodMOAM/v-deo.htmlsi=W9EhrXZdsmi5jYcr ? I could have explained corners better in the original video. 👌👊
Thanks Andy, I’ve had the Fugi ki for years but still opted to spit on my finger. I resealed our shower yesterday following your guide and it’s great. Thanks again
I really can’t thank you enough. I watched the video 3 times, bought all the kit and have just done it this morning. It is by far the best job of applying silicone I have ever done. I was dreading doing it as well but your tips made it really straight forward. Thanks again! Paul
Thank you! I have struggled with silicone for more years than I care to remember, and have probably tried every tool, every trick but never got good results. Fugi kit has been added to my toolbox and all the other crap is in the bin.
Okay, I did it !!!! Probably not up to Charlie’s standards, but far better than the professional who had originally done my shower. I bought the Cramer kit with the blades and handle, so easy to get into close corners to remove the old sealant. I was dreading that first use, as when I first used the shower post installation it had 2 areas that leaked, and despite a return from the plumber, it was never right. As I did this on a cold wet October day I let the sealant cure for 48 hours... no leaks. I am so impressed with this tutorial. Thank you.
Hi Charlie. Watched this a while back and ordered the set. Went on holiday for two weeks and mentally prepared myself to reseal our shower. Came back and went in all guns blazing. Most stressful few hours of my life. A comedy of errors but made good in the end. Looks ace now - like a brand new shower. Thanks for the pro tips. 🙏🏼🙏🏼🙏🏼
Man! This is definitely the most comprehensive and useful video on siliconing the right way. The science and thoughts behind doing a good job you share is priceless. Thanx.
This is an EXCELLENT video! Needed this for recaulking my shower stall. I had just watched another video that did it all wrong, including the soapy water! Glad I found this one.
I ordered these tools. Just used them and followed your tips…. OUTSTANDING RESULTS! I’ve never used silicone but I didn’t want to mess it up… I know how easy it is to mess up. This toolkit and your tips gave me the most professional looking results!! I did the vertical corners and where the tub meets the floor in the first day. Second day I did where the tub and tile meet! A+
Thanks Charlie for a really thorough and informative video tutorial. I was about to spend ages masking up my bath before applying a thin silicone bead and smoothing using my finger. Really useful to know why this is all wrong 😊
showing rather than preaching is brilliant teaching! Demonstrating how voids are created with a finger (ooh er Missus) is priceless and saved me from making similar mistakes. Sorry so many other professionals decried your techniques in earlier videos. Perhaps thy could watch and learn. Thanks for this and all your great videos,
Thanks Chris, you're very welcome. Thank YOU for taking the time to comment. Also check out my corners video ua-cam.com/video/EErbuodMOAM/v-deo.html if you have time as I didn't cover corners that well here.
BLOODY NORAH, by far the best DIY video on anything - not just siliconing. I've been siliconing quite regularly for some 25 years but I will now be using this method. Brilliant!!!
bearwoodcarpentry...Does your wife agree that dipping your tool in washing up liquid gives you better control?..or do you continue to spray into her jointed area?
Great video! I'd like to hear more about how you would avoid getting silicone on the inside corner. I think cutting at 90 degrees and pushing would make it more likely to fully fill the joint and seems opposite that goal.
Please don't apologise for going into detail. It's essential, and it's why myself and most of your other followers subscribed to your channel. Great video.
Thanks Dev. It's a constant battle to try and keep each vid as concise as possible. I just think sometimes, if I don't explain my thought process and why I arrived at a particular solution people might not appreciate why this is better than doing it another way. I really appreciate the feedback, and can't thank you enough for supporting the channel 👍
Hi Charlie, superb vid, love the fact that you put effort into researching these things and share your findings. I’ve been doing ok-ish diy siliconing for years but have just re-siliconed a shower enclosure using your tips, tool recommendations etc. with what I can only describe as professional results. Thank you!!!
Excellent video Charlie! I like your detailed and fully explained videos which even explaining the pitfalls. Your explanations about how using a finger makes thin peelable tapering edges and using tape makes stepped edges are so true and as for the soapy water causing a bad bond (or licked finger that I have heard can cause tongue cancer from the fungicide) - yes, in the bin with those ideas. This video on silicone sealant was interesting to me because I too discovered those plastic profiling tools and find they make a huge difference and a much stronger joint. I'm so glad you mentioned filling up the bath prior to caulking a bead as that's something I also discovered after examining why my joints were splitting off the bath side (whilst sat in the bath🤔). It's also important, especially with a thick bead to leave the bath filled for a day or two until the bead is fully cured all the way through to the back corner. That way when you remove the water the joint comes under elastic compression, relaxes when filled again and never goes into tension so won't pull away. If you empty the bath too soon after beading, the still internally soft bread will ooze into a relaxed shape and the surface profile can distort and set like that, but when you next use the bath the joint will be under tension which is what you don't want. I used to cut the nozzle of the tube at 90° to the desired bead size and press into the joint at 90° or slightly more to push the bead for a very slightly concave surface. Done right it works but you have to be really precise with flow and movement so as not to leave a gap or apply too much that needs careful removal with a knife blade and corners were a pain. These excellent plastic profiling tools do away with all that bother and are so quick there's little chance of skimming over before you are done. One other thing I'd like to suggest is degreasing with isopropyl alcohol (IPA). You can get it 99.99% pure (5L for
Hi…. This video is Fantastic, especially for those who DIY or are just starting to learn DIY like myself. I read your comments, and o have recently just put a post on this video, asking if Nail Varnish Remover could be used as a cleaning agent as well as Methylated spirit and Acetone…? Not that I will be using nail varnish remover as a cleanser but more so if you don’t have both methylated sprit or acetone and are unable to purchase any for any reason. The reason I ask, is because I believe that Nail Varnish remover contains acetone, or acetone can be used as nail varnish remover.
Bought one of the Fugi kits a couple of years ago and they are very good. Along with your helpful extra tips like cutting the mastic applicator at 90 degrees, very helpful 👍
Thank you so much I bought the kit you described and followed your tips. For someone who has never laid silicone before it looks excellent. I had been dreading this job and there was no need whatsoever.
Your right. That process does go against the norm. That being said, I'm converted. Well done, keep it going. I've been doing DIY for years and I thought I knew most things, lol
Thank you, beginner DIYer you should saved me from dozens of rookie mistakes, thank you for not presuming we knew half of the basics (common mistake for usual expert advisors)
Excellent - Excellent Video. I’ve installed kitchens & baths for 30 years, and I’ve made every ‘Don’t Do This’ mistake shown. In the cutting the tip too small department, sometimes it also causes the caulking gun material to curl up and away from the joint. I often check my guns clearance with a full tube in it, and the pushrod extended so I can find my difficult areas to reach before I start. I keep a nearly empty tube for tight spots like behind the water closet. I often shape the following edge of caulk tube tip into a cove or 90° so I don’t have to come back with a shaping tool. I cut the leading edge most of the way through with a wire cutter, then shape the following edge with a razor knife. For tight spots, there is a canned silicone with propellant (Flex Shot) which is great for tight spots and frequent small jobs. The tip is smaller than most unscrewable tube tips and easier to clear.
Thanks buddy. You've got some great tips there. There are also swivel nozzles for getting into tight spaces as mentioned in this video. 👊 ua-cam.com/video/EErbuodMOAM/v-deo.html
Thanks for your honesty on this mate. You're right - the spray method looks great initially, but what the spray evangelists who have got very angry with my video don't see is the aftermath 6 months or so down the line when the joint starts to fail. They probably don't get many call backs because their customers just assume that silicone is only meant to last that long.
Manual: The surface of Mapesil AC must be finished off with a damp tool, preferably moistened with soapy water, before a superficial film has formed. Thanks
@@polrze Hi, novice here (me, not you). Perhaps this is a general rule, not necessarily required to be followed with the tools demonstrated in the video due to their material (this is a guess). I also guess that a damp tool shouldn't be confused with spraying the silicone directly. I would guess a damp tool might glide better if it's made of a material that the silicone is likely to grab to, without the adverse effects of spraying directly.
Thanks for the video. I´m former sanitary serviceman and now I realized what I was doing wrong.(not cutting the tip to wide of tool and using detergent water) My tomorrow job at customer´s shower corner will be an easy job now. Many thanks.
Rather than that plastic scraper thing to get the old stuff out, I use a sharp wood chisel. Satisfyingly successful, but it DOES have to be sharp. Great video! I’ve been siliconing for years but still learned a lot from this. Nice one chum 👍
Hi Phil, thanks for the comment - much appreciated, particularly given how long you've been siliconing for! Yes I can see the merit of using a sharp chisel - you get enough power into it to totally scoop clear the silicone, in a way that you never can with a scraper tool or even a Stanley blade.
After watching a lot of "how to" videos which turned out to be "how not to" I'm so glad I found your video. You deserve a PhD in siliconing because you've actually applied some science and experimentation to the subject! The "don't make it concave" section was particularly enlightening and makes perfect sense, yet everyone seems to do the concave. I've always questioned the wisdom of soapy water but always got the response "that's how it's done" - now I know I'm not going mad, so, thank you !!
Been joint sealing for 20 years inside and out. I agree with most points and disagree with only a few. Use a sharp chisel to remove old silicon, especially when it's hardened. It cuts through it faster, less effort and last a lot longer than any Stanley blade does like in your video. When time is money and you have to get 10 duplexes done in a day with two full size bathrooms, wash room, laundry, kitchen and entire down stairs if they're tiled swapping out Stanley blades 2-3 times a house is just a waste of time & money, especially when your doing the initial sealing when the grout and tiling glue is jutting in and out of every joint which is how tilers leave it these days. About the spray bottle. It's the preparation and application of the joint and silicon that matters, if you apply it badly it won't stick whether you use the spray or a spade (what we call your kit thingo) or God forbid your finger. Sprays help make clean up a hell of a lot easier when things get messy to. We've all accidently dropped our bit or let the gun run a little too long in one spot etc and all you gotta do it wipe it off. When it comes to the spade kit, it's a waste of money for 95% of all applications. You WILL lose them and they just aren't worth it, for just a diyer sure but not on a job site, shit always happens. You won't be using 90% of the other angles on them but it is nice to keep in your truck if youre given it. It may seem odd but a simple but a spray and a paddle pop (ice cream stick) does the job as good as anything. You can manipulate it to any angle you need, inexpensive you can get a pack of a 1000 in a crafts shop or online for a $2 and you have a constantly supply of you like ice cream like I do XD. Another trick is with your joints and many others I've seen is you take off the raw silicon with a tool/bit/spade whatever the tool with always leave a wavy look to it like in your video when you show how you do it. Thats obviously because a number of things: tool is worn down in places, tiles arent level across, hand movement, friction etc. What I found that gave me perfectly smooth run was after taking off the initial run (this will sound weird and yeah I've got looks before from clients and supervisors) lick a finger and run it along the joint moderately lightly. Your not trying to push the silicon into the joint you're just smoothing it. Again as long as you're not using tape or God forbid only your finger then youll be good as gold mate and some of my tips or disagreements only apply to on site working where time is paramount. But preparation and application is the absolute top tip you can give to a new comer not so much technique. But it's better to be good with all three steps. And if you do sealing alot or as a job. Get a battery silicon gun. I wish I got one sooner but that thing will save your arse when its only just above 5*c in a house or outside and you got a full day ahead of you, it's easy to heat up a silicone tub but its bloody annoying and if gotta keep working then trying to squeeze out cold silicon is a right prick to do all day. Anyways I typed to much, Great vid.
I do an absolute shed load of siliconing at work, fitting kitchens and bathrooms etc and although I don’t have this specific fugi tool kit I do have another variant. After watching this though I’ve just ordered one as I like the attachments for them. Once your used to them you get just as quick with the formers as u would just using your finger trust me! Great video👍
Marc Gray Thanks Marc. Great comment, and it's nice to hear from a pro siliconer who is open minded enough to use a profiling tool and to acknowledge the benefits of the FUGI. I get a few old school finger siliconers commenting who just cannot accept their technique is flawed and outdated! Thanks again.
Not a problem matey... I’m 27 and always looking for new ways of doing things... upset the older ones! don’t get me wrong some old methods of doing things really are the best, but not in this case!
I watched this video after my first botched attempt at siliconing around my new bath. I bought the Cramer kit and with a bit of care and following Charlie's advice my bath seal now looks great. The cramer tools are a cinch to use, even for a dolt like me. Get the profiling kit 7 that comes with the scraping blade tool - it's marvellous!
I have been a handyman for years and own my own maintenance business , sad to say I was taught the completely wrong way by another tradesman. Just purchased a set of profiling tools :)
Finally someone who took the time to show how it's suppose to be done. Will be doing a kitchen renovation and installing backsplash now I know how to do better than most professionals that just use fingers and tape. Thanks
@@CharlieDIYte No problem - as @DAVAD M DAVAD said, I appreciate the proof you supply with your logic. I have a problem that I hope you can help me with, though. I can see the benefits of using the FUGI Kit where the top of the bath is flat and at right angles to the wall. Do you have any tips for coping with a bath that has a raised shoulder before it drops down again to meet the wall?
This is a very good guide to do a quality job. However everybody has their own methods of doing things that have some variations. I have caulked hundreds if not thousands of shower/tub surrounds over the 35+ years of owning a solid surface company and many of the caulking jobs I've done have lasted for 20 years or more. To add my 2¢ into the equation, if you follow this guys method you will get a good result, however I would refrain from using any acetone. It leaves a residue which over a short period can result in an adhesion failure and soon turn black from mold and goo. Use the Denatured Alcohol. I used an industrial spray bottle, it allows for applying a mist instead dumping it out of the can. Industrial spray bottles can be found at most hardware stores, they are usually dark grey. The standard Windex bottle trigger pump will fail quick from the alcohol. Next, I recommend removing all/any old silicone. There is a reason that you're replacing it and why chance having it fail because of an existing issue. It can be very time consuming to do but the key is to have it last. Then, once you have got the joint/crack cleared of any bad/existing material clean it good. Use the Denatured Alcohol to prep the surfaces for good silicone adhesion. Spray the areas with Alcohol Just mist them wet not drenched and use white paper towels as wipes. Do not use towels with fancy colored patterns on them as many times the ink will bleed and leave a slight hue to a finished job. Let the ares sit for at least an hour to completely dry. Alcohol does dry quick. Apply the silicone as instructed in the video plus only do about a 2 foot stretch at a time because if the silicone starts to dry (even slightly)it will develop a "skin" and it will pull the bead and make tooling difficult. Now the guy does make an extremely valid point about getting good penetration into the seam and full adhesion without gaps or bubbles in the caulk is important, although if it happens you can always spot fill. Tooling the joint. I have use the fancy caulking tools he shows and they do work well, but if you are doing this just one time save the $10 - $15 and go over to the kitchen department and grab a few of those Formica chip color samples. I used those for years. You can use them as they are or sand down the corners to make any profile you want. Plus they are thin and make tooling a corner easier then a thick tool. Regardless, either works well. I've even used my finger on a lot of jobs, just make sure they are clean first. Now the biggest difference with my final method is how to do the tooling. After running my silicone as smooth and without voids, I use the alcohol spray bottle to lightly mist the bead before I touch it. They guy is right about not using soapy water, Only use alcohol. Besides silicone is waterproof even before it dries. The reason for this is because you want no silicone to stick anywhere but where you put it and to just tool it dry can lead to it smearing and leaving a minute film that can eventually peal and possibly affect the finished bead over time. Also if you get some silicone somewhere accidentally, the alcohol with a paper towel makes it easier to clean up. Now, even the best professionals don't always do the job without a spot or two that the silicone didn't stick well or came out of while tooling, so just allow the alcohol a little while to dry and go back and spot fill. My biggest piece of advise when you do any silicone work is to keep it clean. Always have at least a full roll of paper towels within easy reach and an open garbage bag to throw them in. Don't skimp on the towels because once you get silicone anywhere other then where you want it then you've got a nightmare (cleaning silicone finger prints is not fun).I never liked using rubber gloves doing this because you lose the feel of the small areas. It doesn't take much to go everywhere and clean up (especially once it dries) can be labor intensive. Also wear clothes you don't care about because this stuff won't wash out.
Terry Dillon You give some great tips, but I must say in Charlie’s defense he did cover some of them. In regards to caulking over caulk (silicone), the caulk that he was caulking over was in great shape. You are correct though that one should never caulk over moldy or dirty caulk. That’s just gross and disastrous. I do appreciate your wealth of information. Thank you for sharing :) Between you and Charlie I’m ready to tackle my project.
@@louised6790 Many times when there is an issue of mold or contamination most of it is usually behind silicone that appears perfectly sound. Many times as I have removed existing sealant, mold and such are exposed on the back side of the bead you are removing. The contaminants in most cases work their way out from behind the surface instead of from the surface inward. I believe they are caused by a failure or void in a small location and as moisture penetrates it does not dissipate deep inside the bead and the contaminant remains and leads to future failure, hence the need for frequent spot repairs.
Terry Dillon YIKES! That makes total sense. I actually knew but it didn’t dawn on me in this instance. Well I feel silly! Thank you for bringing that to my attention. I’m getting ready to tackle a shower where they laid a grout line between the tile wall and the tub and they did it again outside of the tub and the tile flooring. I haven’t had a problem at the floor but the grout inside the shower in molding. I can’t believe they did that! I’ll keep my eyes peeled for anything deep inside.
@@louised6790 Once you get all the horrible gunk Out Karen, make sure to go at it with a 'Hard' Level Toothbrush (or any old ones you've got laying about !) And give the Whole area a really good Disinfectant Clean - evening time, before bed is good for leaving it 'overnight' ! As I expect you're like myself - once Started, don't Stop !! After a lot of years, It dawned on me - like one of those new LED lights ! - that I was Missing things, or promising to get Back to Bits, that weren't quite right ! In order to be Finished ! Due to Chronic illness I can't do Any of the DIY things I used to, but it Pains me to watch some (¥£€¥₩) take 2days to paint & wallpaper a room - things I used to do (start to clean up!) In a Day and a Half ! But, as my wife pointedly remarked after a few moans about "so-called Pros"! That THEY had Working Hours, which meant they, unlike me, didn't get finished at 5am, or go to bed reeking of White Spirit.!! So, do What you Know you Can do, and get someone in for the Stuff you Can't ! Or another good trick is to offer a "helping hand" because you really want to see How to Do It, because you're thinking of taking a Course ! Most of All....Be Proud...🤗. Of What You've Already Achieved !👍 HOPING 2019 BRINGS U & Urs: PEACE✌HEALTH💛 &😊HAPPINESS😃 🍀POD🖖
What's excellent about your presentation is you give the reasons behind every point. The explanation of how the pre-application of soapy water prevents a good bond was especially helpful. Thanks!
Charlie, thank you so much for sharing your great knowledge! I used the Cramer Pro Guide and got perfect results. Again, thank you for sharing! Best regards, John Ellis. Aldie, Virginia. USA
Hi John, I'm blown away that my little vid has reached as far as Virginia. So glad you found it useful and I can't thank you enough for taking the time to comment - it's what keeps me doing these vids 👍
🛠Charlie DIYte Amazon Tool Store amzn.to/3fcLnY4 - all my tried, tested and much loved DIY tools. Help support me on Patreon -www.patreon.com/charlieDIYte (includes Discord access).
Best caulking demo ever!! Thank you so much - this was so helpful! The fact that you took the time to explain how the standard techniques could cause problems, and you even showed close-ups - to me, that made all the difference & convinced me your way is the best way. I appreciate you sharing this. Thanks again!!👍💗✌️
So this isn't a SALESMAN?
Thank you so much for such detail in the "don't do's" This is the first video I clicked...Worth every minute...
As a professional builder for over years, This is one of the best explanation videos I have ever seen on the subject. Thank you so much for the time you have put into this and thank you so much for the quality content, you rock!
Thanks so much mate, I always think it speaks volumes when a professional builder is humble enough to tell me I'm doing something right. 😉 Shows you're still hungry to learn and therefore that you're clearly very good at your job (after all, we never stop learning)!! Take a look at this one if you've got a moment as I didn't tackle corners properly in the vid you've watched, but clearly it's not always practical for you guys to wait for a joint to set before finishing it. Thanks again 👊 ua-cam.com/video/EErbuodMOAM/v-deo.htmlsi=OMqy7xUv2Mvcx8vp
This is my go-to every time.
Wish I'd seen this years ago! Just about to do my shower tray. I did buy the tape to go around, but it didn't work. VERY good explanation. I've always used detergent and my finger, with the results you described. I'll now buy the tool recommended. Fingers crossed! Thanks again
❤@@CharlieDIYte
The painters tape caulking trick never worked for me n i used to sit n cry n redo it again n again for two decades. Finally a person who shows the same flaws in the technique which i experienced. Thank you
One of the most crystal clear presentations I've ever seen on any topic on YT. The first seven minutes, explicating in meticulous detail how NOT to apply silicone, is invaluable. (I have for years followed as standard practice almost every single one of these DONT's.) I am a professional finish carpenter, with a keen interest of late in improving my caulking game. This video delivered more useful content, accompanied by an incredible degree of logical explanation of underlying principles, than I could have imagined exists. Thank you!
Thanks so much Michael, I really appreciate that. As I always say, a professional tradesman who is still receptive to learning new skills or challenging what he's learnt over the years is clearly very good say his job 👏 If you have a moment just check out this video too ua-cam.com/video/EErbuodMOAM/v-deo.html as I didn't cover corners very well in the one you've watched.
It's funny as I just watched a video on Home Depot and they used tape to mask and their finger to smooth out.
Crystal clear presentation?? WTF? Folks making caulking how to videos and making up their own bullshit nonsense. I was in real caulker for many years and none of these utube videos are anything even close to “ pro “ actually he’d be fired so fast just like So many others. I worked for one guy who already Fired 12 Mostly Real Caulkers who all of which were way more skilled and knowledgeable than this wanker
As a girl who has never DIY'ed anything in her life, let me say, this video was amazing. As someone else said, who knew a 20-minute video on silicone could be interesting! You really do make it interesting and easy to understand, though. I now feel ready to redo my landlord's awful silicone job. Many thanks, sir!
Aw, thanks so much for that! One thing, if you've got any vertical sections to do/ corners, check out this video too, if you haven't already ua-cam.com/video/EErbuodMOAM/v-deo.html 👍
How did it work?
@S. O. You posted your comment 2 years ago about redoing your landlord’s awful silicone / caulking job, so maybe you can’t answer this, but do you remember how you removed the caulking? Did you just cut it with a razor? If you recall how difficult the removal process was, please let me know!
@@saraohara2504 get a caulking tool kit.
You can also use a Stanley to remove old/mouldy caulking.
I am not a diy person, have never siliconed anything in my life, followed this video to the letter and am very pleased with the outcome, many thanks.
That's awesome news Stuart. Great work and thanks so much for letting me know. 👊
@@CharlieDIYte sick and tired of seeing people using the tool the wrong way round and this fekin spray,,, as you've pointed out quite clearly the soapy spray goes behind the silicone, as an engineer and Builder now in my 50s, when this tool first came out many years ago the rep described the silicone tool as the ultimate tool for silicone and you must use a soap spray, and I am probably 80% certain he used the tool chamfered going against the silicone, then many years later on another job seeing this guy using one of these tools, no spray and the sharnford Edge behind the flow of Direction, as in the video,,,,, yep we've all used fingers and tape, and to think back in the day we used to lick our finger and run it over the silicone then again and run it over the silicone,, dow Corning silicone in Barry South Wales, fabrication company I worked for at the time we did a job inside there, pesticide fungicide and chemicals that went into the silicon, the industrial silicone mice likes the stuff apparently hence the pesticide, I told this guy i used to lick the silicone for smoothness he said I'm surprised I've not got an extra toe growing,, good video man...
Dave
14 years I've been a Floor Layer and I've always hated siliconing. I came across your channel when trying to find the right drill and this came up in my suggested yesterday. I tried this technique today and its so much easier with such a professional finish. For any tradesmen reading, you get a lot of waste as Charlie shows but you just need to add the cost onto the job. Nothing worse than a decent looking vinyl or luxury vinyl tile job and poor sealant finish. Thank you so much for this great demo, and if you haven't already, I would highly recommend subscribing to this awesome channel 😊
Aw, thanks so much John, I really appreciate that. As you say, you do get waste by virtue of the way it works but don't forget the waste was amplified in my case because I was applying such a wide bead, and if the waste upsets people, as long as they're quick, they can tool it into the next run before smoothing with the tool. Plus the bead is so much stronger so you're doing your clients a massive favour, particularly on a floor that they'll be cleaning often. I always think a tradesman who is prepared to embrace new techniques (ie prepared to innovate) is clearly very good at their job 👍 Thanks again.
Holy cow this is a game changer! I've just done the bathroom in about an hour with no swearing or covering myself/the room/kids/dog/wife in sealer. Thank you
Lol 😂 that's always good
I’ve worked in construction for 30 years and what i love about this video is the open mindedness to question supposed tried and tested methods like the fairy liquid in a bottle. UA-cam is such a great resource
Thanks so much Steven. Can I throw that back at you and say that anyone who has worked in the industry as long as you but who is still receptive to new ideas/ processes is clearly good at what they do👏 If that guy hadn't trolled me I'd probably never have done this video but I was so perplexed at how the soap bottle brigade had got away with this for so long I felt something had to be done about it.. Thanks again!
Hi Charlie, i’ve been a homeowner for 35 years and I’ve made every caulking mistake possible. With your help, I now have the knowhow and skills to create a waterproof and good looking caulk seal.
As a science fan, I appreciate the cutaway view of what’s happening. I also appreciate how you have put aside convention (45° tip) for what you know to be true! Thank you 1000x!!!
Thank you for this tutorial Charlie. I followed your instructions to the nth degree and everything slotted into place. I’m 76 years old and I’ve been a DIY enthusiast for most of my life. I’ve lost count of the number of bathrooms I’ve refurbished and never as Silicone been so uncomplicated and easy to apply. You are amazing! Thank you.
Kenneth, thank you so much for your wonderful comment! I'm so chuffed it worked so well, which of course it would as you implemented it so meticulously! You've probably already seen it, but for future reference I also have a corners video ua-cam.com/video/EErbuodMOAM/v-deo.html Thanks again 👍🏻
I know this is an old video but being a pretty naff diy'r, you have inspired me to seal my own bathroom...being 41 and scared to make a mess I watched this, subscribed to your channel and did my bathroom...thanks mate, truly, thank you
So pleased to hear it went well, Daniel and massive thanks for subscribing 👊🏻
I bet it looks awesome! Good for you trying something new even if it was a little intimidating at first.
I just wanted to thank you for this video, I'd been putting off resiliconing a shower tray that had a slight leak but watching this allowed me to approach the job with a plan and do it correctly.
Thanks so much for getting in touch. Really glad to hear it's gone well 👍
I have just done the nearest thing to a perfect seal that I've ever done in my life. Why did I not find this guide and this tool 40 years ago? Absolutely brilliant!
If I had a company, I'd hire you as the VP of Quality! I love the attention to detail and the power of keen observation! Thank you for taking the time to educate all of us.
I like that you go with what you know works with reasoning to back it up..
Many tradesmen are taught the one way and never consider there could be a better technique.
Peer pressure/ridicule among onsite colleagues ensure they never try a different method.
Keep up the good videos.
That's exactly right, Joey, but the really good tradesmen are the ones who have commented on here that they've watched this technique and realised they've been doing it won't all these years. Someone who is receptive to new techniques is, I think, clearly conscientious and good at his job!
I've just done my bath following your instructions and I'm delighted. A more clumsy and hapless individual than me would be difficult to find, so it was a bit traumatic and there was as much silicone on me as on the bath, but it looks good and strong. We did it the "traditional" way last time and everything that you said could go wrong, did go wrong. So thank you Charlie (and hubby can do it the next time).
Yup, this is the best video on this subject by far.
So many videos on youtube repeating things without any explanation, like “cut your nozzle at 45 degree angle - just because...”
Never made sense to me, when a 90 degree angle is much easier to work with.
And the soapy water spray always fucks up my silicone beads.
The Gordon Ramsey of silicon application.
Ha, thanks 😉
Watching a silicone video but can’t spell it 😂😂,or is it an American version of English 😮
The ultimate insult.
This is a really great, no BS, plain English explanation and demonstration of what I've been doing wrong but didn't really understand 'why'! Just Ordered the Cramer tool - omg they're so good; my 'grouter's-sealant finger' was delighted! Thank you so much for this Charlie; massive shout-out.
You're very welcome Jules. The Cramer tool is awesome isn't it. Check out my corners video too ua-cam.com/video/EErbuodMOAM/v-deo.html if you've got a moment as I didn't really cover corners in the vid you've watched. 👍
Agree, good content but the verbosity…… I won’t go on.
I like how you explain, why, knowing why is very important. Adults need a reason. Keep up the great training videos.
Absolutely, it drives me insane when the host of a tutorial video gives instructions but doesn’t tell you WHY something needs to be done. It leaves you in the crappiest position for troubleshooting.
I never leave comments on YT but I've just followed Charlie's instructions to the letter and the result is incredible. Absolute game changer
Cheers mate, really appreciate the comment. So chuffed you nailed it. For corners check out this vid ua-cam.com/video/EErbuodMOAM/v-deo.htmlsi=I5IY3FNcqOe5vxYZ as I didn't cover corners properly in the original vid. 👊
@@CharlieDIYte Thanks Charlie, I did struggle with the corners a little. Will definitely check this out before my next silicone adventure.
This was amazing - I made a proper stuff up of my bathroom about a year ago (it looked alright, but the silicon lifted quite quickly after applying). I watched this video before doing it last week, and went out and made sure I was properly prepared this time. Thank you so much for making this freely available - you're helping millions of people (by the view count), and I hope your business is blessed and booming.
So glad to hear that, Tim. Did you see my corners vid too ua-cam.com/video/EErbuodMOAM/v-deo.html (in case you've got any other siliconing to do). Business is fine thanks. It's never as easy as it looks to make money from this, which is why I've set up my Buy me a Coffee channel now I'm doing this full time, but I'll get there in the end 👍🏻
This honestly makes sense. I always thought the detergent spray method would ruin the caulk that was just applied. Thanks for the lesson.
I don't usually comment, but the level of work, thought and information you provided here is worth at least taking a second to say thank you!!
Aw, thanks Siva. I'm blown away by that. If you're planning a silicone project check this video out ua-cam.com/video/EErbuodMOAM/v-deo.html as I didn't mention corners in the one you've watched. 👍
I just did my GF'S Landlords shower following your methods step by step, and it's turned out amazing.
Some of the tile joints were over 10mm away from the shower tray, and some touching it, uneven tiles, the lot.
I've probably done something like this about ten times in my 48 years (for myself) and it's never been close to looking as good as this.
Many thanks for making this video Charlie.
That's fantastic. Well done buddy and thanks so much for getting in touch. 👊
Wow- I've been remodeling homes for over 40 years, and thought I knew how to caulk. This video took my scale to a whole new level. Bravo, Charlie! Now I'm going to have to look at your other videos and see what else I need to learn from you?!
Thanks Karl, really appreciate that. You might take a look at this one ua-cam.com/video/EErbuodMOAM/v-deo.html for doing corners. 👍
Great video, I'm a DIYer and have been using the Fuji tools for a few years now, but still learnt a couple of things from your video. One tip I have, if you have the luxury of time, is never to do both sides of a corner on the same day. I do one side and then come back next day and do the other side after the first side has dried. Gives a perfect mitre joint. Maybe need 3 days for a 3-way joint.
Genius. I like the idea of not simply explaining why or why not to do something but demonstrating, that really helps.
Quickblood1 Thanks - really appreciate that!
Wow! Thank you for the educating us on how to properly caulk a bathroom.
I used this product and method. I am a trained carpenter so this is proper respect. Like everything it takes practice. I was massively impressed. I have a near perfect finish. I love the way you can work and rework. I have a couple of niggling criticisms maybe with the descriptions but minor over all massive thumbs up . Less cooks makes a better broth
Thanks David, I appreciate that. Yes I accept it wasn't perfect, and I omitted corners, which you can find in this video bit.ly/3c7SKio but overall it gets the hedge across. Really pleased it worked for you. It's no surprise to me that you were receptive to a new way of doing things - the hallmark of a good carpenter 👍🏻
@@CharlieDIYte So many folk can barely read instructions, let alone listen to someone trying to teach them a different way of doing things. It affects the industry and consumer detrimentally and QOL in the UK somewhat. My uncle designed a bathroom for Phil Collins down in Brighton so maybe thats where I get my difference from :)
Brilliant pro video, I've been building and fitting out houses for 40 years and although I thought I was pretty good I got several points from this that I'd never considered! Thanks for spending the time to do a great demo.
What a pleasure to watch - a breath of fresh air. Loads of common sense, and lots of received wisdom challenged clearly and eloquently. Who says a 20 minute video on applying silicone can't be interesting!
Thanks so much Chris!
Well said Chris
I have to say I consider myself a seasoned siliconist.
After watching this video I am forced to rethink my self taught methods. I really take it as a positive though, so thanks for showing me where I may have been doing things incorrectly, and pointing me in the right direction.
This really is a useful video. I know there are trades out there that will argue tooth and nail that their method is best, but you cant really argue with the detailed information in this video.
In my humble opinion this is pure gold. Thanks Charlie
Have never used silicone in my life, my boyfriend attempted to silicone our bathroom a few months ago and did an awful job, so thought I’d do my research and show him I can do a better job! 😂 this video was amazing, I was about to just go for it and use my finger to smooth it out but quickly learnt from this vid, that this isn’t the way. My boyfriend came home and didn’t believe I’d done such a good job, so thank you so much 😁
Perfect advice, thank you! I really didn't like doing silicone before, I've now completed a near perfect silicon application throughout my bathroom.
Fantastic news Andrew. Thanks for letting me know 👍
Brilliant video thanks! I have bought the FUGI kit and it is great tool for the job. My only issue is I have quite an old house where lots of the angles of tiles etc that have previously been laid are not square to the wall, so the 90 degree FUGI tool would not sit in the joint. Gaps would appear as I would drag the tool along. I got around this by actually making my own tool from a credit card for these awkward places that the FUGI could not reach.
You can angle the tool slightly so a 90° tool it fits into an other than 90° edge to a wall. The similar tools I got from eBay have some angles greater than 90° and some less but all can be used on a 90° corner by angling and keeping both bottom and wall edges flat against the tool edges. The same would apply if the wall leans out or in although its probably best to have the tool at 90° to both bottom and side ideally.
Charlie, you're right. This is just about the opposite of what I've seen and learned and you explained why some of my project came out less than beautiful. Never realized how useful the silicone caulking tools are. Used to always use my finger. I'll be purchasing a set soon. Thanks.
Thanks for that. Yes, go for it, you won't be disappointed!
Sir, I thank you VERY MUCH. Your tip to do the verticals first and to not spray with soap until the silicone seals everything it's supposed to was invaluable.
I had the entire bathroom and toilet sealed wrong by the contractor, floor to ceiling. I spent 3 days removing all of that with countless razors and scrapers, in the end resorting to Knauf solvent remover for that perfect 'never touched by silicone' finish.
Now I have to do it right and some trials showed me you taught us all well.
I am chemist and i wondered about surfactants being used on caulk. It would never stick… and there you have it. Exactly. Many thanks
Hi Charlie, I just wanted to express my appreciation for this video and how helpful it’s been for a newbie to siliconing like me. I followed your dos and donts and the job got done with a much better result than I expected. I have now been able to re-silicone my shower tray and the bathtub. Thanks so much! My next project will be re-caulking my wooden window panes 💪🏻😃
Nice one Charlie, have been ‘caulking’ for years; watched your vid and purchased the 7 kit, what a game changer, brilliant results. So easy, working in short sections, first caulking job I have ever finished without swearing or going around the house shutting doors. Thanks Charlie, well done mate 👍🏼👍🏼👍🏼
😂 That made me laugh!
Short sections? Why? You can either run the gun or you cannot you can either knife ( tool) or you cannot And NONE OF THESE U TUBE IDIOTS HAS A CLUE!!
Charlie: I thought I am a very competent DIY'er with many years of house building/renovation behind me. I am also Architecturally trained and so have an eye for details (poor siliconing has always bugged me y contractors). I just wanted to thank you for your informative video. I thought I always did a good siliconing job but after trying the Cramer kit (from your recommendation) I will for one NEVER go back to taping or using washing up liquids. I cant believe how such a simple set of tools does such an impressive/fast and neat job. All fillet depths are catered for and the semi flexible rubber tools allow total pick up of any overspill. The secret if there is one is to clean off the tool frequently every foot or so. If the silicone does snag (as some makes of silicone skin unbelievably fast) or there is a dip just fill again and go over. Thank you so much ! The best 20mins of my DIY life and £14 I have ever spent_All power to you for showing this so well. Anyone who promotes washing up liquid or a finger is a total hack. And now I can prove it. This knowledge is also now going on site with me, so sloppy mis-informed contractors beware !
This guy has to be one of the best on UA-cam. Very detailed step by step explanation & backs it up with a demonstration so how can you fault him? Thank you for taking the time to share your valuable skills.
You're very welcome, Harry. Thanks for the comment. Take a look at my corners video if you have a moment ua-cam.com/video/EErbuodMOAM/v-deo.html as I didn't really cover corners properly in this video 👍
Charlie. I am a professional bodger - if it can go wrong, it does. My shower and main bath were in desperate need of re-sealing and I was dreading the cursing and frustration that would inevitably lead to a shoddy result.
Having found your video, I saw a glimmer of hope - could I possibly undertake the work without pain and end up with a decent finish?
Well, yes and yes - I'm delighted. The only thing I would do differently would be to buy a silicone kit with the transverse joint attachment - mine didn't have this.
Having subscribed and looked at some of your other videos, I am feeling confident at tackling more jobs around the house.
Many thanks and keep up this great work. Adrian
Adrian Jarratt Hi Adrian. Thanks so much for taking the time to tell me how you got on - comments like yours are what inspires me to keep producing these videos! Absolutely delighted that you pulled out off! If you can silicone successfully the world of DIY is your oyster my friend! As my video has hopefully shown you the bodging had less to do with your ability and more with the preparation and application! Keep up the good work and many thanks for subscribing!
Thanks Dennis
Genius, have just siliconed new bathroom using all the 'do not' use methods and, already experiencing the issues shown. Wish I had found this video first.
Now going to redo and, use this video as my master guide, great work.
OMG! WHAT?? You are the most perfect example of what all the repairmen & carpenters etc keep constantly referring to as the "Retards that keep them in business"! All these dumbest humans in history, the dumbest humans possible that watch a home improvement show & try to do things themselves, completely mess it up & have to call a pro to fix it. & HOW can you have messed it up anyway when EVERYONE I know was "born" with Common-sense & will tell you that Silicone is the EASIEST thing u could possibly use! I mean HOW can you not even use "Glue", & not just any glue but "Rubber" based glue which is the Easiest possible, there is Only "3" steps that NOBODY should have to read instructions to know either, 1, make sure the surface is fairly clean (Which barely matters as Ive siliconed Many things that have been dirty, covered in sawdust or even "wet" when using most bathroom or plumbing silicone that clearly says it works on wet surfaces) 2, it literally just squirts out onto the surface & 3, smooth it out usually just with you finger! So HOW the hell could you FAIL at that? You realize its literally a well known fact that anyone with half a brain & common sense will tell you that its HARDER to brush your teeth than it is to use Silicone. I mean stupid, you just commented & used the word "Genius" for a video on HOW TO USE GLUE!! & the easiest glue in the world at that! Ive used silicone since I was 13 & its literally IMPOSSIBLE to mess it up! Its just Rubber based glue, thats it, & even easier than other glues it wont sudden;y dry on you fingers etc so u have ages to wipe it off & even plumbers & carpenters etc just use their fingers to spread it. WHAT is there to possible mess up? There is NO way the single dumbest humans in existence should ever be allowed to breed, Im TERRIFIED to think that you may have kids, people this insane & incredibly stupid should NEVER be allowed to breed, I mean if u cant use Rubber glue theres NO way you could ever drive a car, feed your children, I mean if u cant use silicone then u wouldnt be able to even brush you teeth, HOW is it even possible for supposed "humans" like you even exist? When humans are "Born" with Common-sense, Im not joking or exagerating when I say I dont think someone this dumb could even come close to being called a "human", Im TERRIFIED for my kids & Every single other child out there to know people out there as braindead or retarded as you exist.
@@VirusOfCyrus
Your comments say more about you than about anyone else. Very aptly named - "Virus". By including your friends in your rant, you are also insulting them.
Pity you have so much time on your hands to attempt to insult others, than doing something useful with your own life.
I want to cry right now. I also just did a lousy job on my bath and now I found this video.
@@VirusOfCyrus talking about missing the point
... and some very important points while you're at it raving on about common sense.
Watched this again earlier today as I had another bathroom to do. It really helped me. I have to say I was very pleased with the tips about cutting the nozzle straight rather than at 45% and also cutting the nozzle at the same measurement as the tool you use to finish. Very good tips and I was able to do a real good job of my mastic thanks to this video - nice one.
Thanks Bill, really glad you found it useful. There's also this one bit.ly/3c7SKio for corners of you have a second, as I didn't cover corners particularly well in the vid you've seen. 👍🏻
I always enjoy watching your vids. Even though you did this 5 years ago, you always reply to questions. A class act. I'm the DIY'er in our house as my husband hasn't a clue! Been married almost 52 years. As he says, more than 3 life sentences. I have always liked to be able to "sort" things out. Keep up the good work.
Absolute genius, I had no idea about fugi tools or low/high modulus sealants, I was about to do it all wrong. Looks amazingly neat. Thank you.
Thanks mate. Check out my corners video too if you have any of them to do bit.ly/3c7SKio
These are just the best DIY videos I’ve ever watched. Charlie is a real quality guy and it shows in all the detail he goes to as he explains what to do. I also like the fact that he’s open and prepared to diss some old views on how to do things as he explains why with clear logic and demonstration. Top of the class to me.
Thanks so much David. Check out my corners video if you have a moment as I didn't really cover them properly in this one ua-cam.com/video/EErbuodMOAM/v-deo.html
What are the tools called were can u get them from.
All these caulking videos on utube are absolutely horrible and completely clueless on caulking and everything related to it
Being an electrical engineer, one of my heroes is Michael Faraday.
You are the Michael Faraday of the DIY: logical, precise, elegant & simple!
Just watched your video again now that I wanted to renew my shower cubicle tray sealant which had been installed by a professional 6 yrs ago. I have always hated doing sealant repairs as in your video there are lots of ways suggested by people. I purchased the Cramer 7 kit which comes with the removal tool and blades---what a worthwhile buy, used the tool with one of the sharp blades(not the grout one) honestly it just sliced through the old sealant and then cleaned up any remaining bits. The blade point and angle is just ideal and if used carefully does not damage the tray. I followed your advice about the sealant gun nozzle width(the gap between the shower tray and shower wall was really small) so using the 10 mm blue tool(a similar gap to the old I removed) I successfully finished it off and only needed 2 passes and although it does waste some sealant I was amazed at the finish, there was a small bit near one end that had a slight mark but decided not to tamper with it ! The Video and the kit has mad me more confident to deal with sealant jobs in the future. I have watched several of your videos over the years and find them clear and concise and very informative.
Resealed the bath today, after watching this video a couple of times and buying a Fugi tool. WOW ! Can't believe how good it looks, amazing. Never thought I'd ever get to do it like the pro's, but seriously impressed with the results.Can't wait to do another one. Cheers Charlie!
Get in!! Well done, and thanks so much for taking the time to feedback how you got on!
Best advice ever, i have just re sealed my shower / bath and it looks amazing, never thought i'd ever get such a finish. lot of nonsense advice on YoutUbe BUT NOT this video, thumbs up
Bang on!
@Francis Rodrigo Ceblano hahaha
qqqqiiioqjkjjjjjikiiu
P
Wow. Like everyone else, was just about to do my bath in the "don'ts way" - now changing the plan. Thank you a million!
Ha ha me too
OMG... Your comment has made me TERRIFIED! Like I so scared for all the children in thew world knowing that there are "somehow" actually humans like you out there that actually werent born with "Common-Sense"! U didnt know how to use Silicone?!? That shouldnt be possible, its literally the EASIEST thing you can do in life besides breathing, its 200% easier than brushing your teeth (this is NO sarcasm or exaggeration at all either) There is literally "3" steps, make sure the surface is clean enough & isnt oily (it doesnt even have to be very clean or dry either, Ive used silicone on very dirty surfaces b4 or Subwoofer boxes with quite a lot of saw dust & it doesnt matter) then it literally just squirts out & u smooth it off usually with you finger, THATS IT! HOW can u mess that up or not know how to do it? I was 14 when I first used Silicone & I didnt even need to read they instructions, all I read was what ANYONE with half a brain would which is the drying time, Silicone is literally Rubber based GLUE! You cant use glue?? Firstly if your this terrifyingly braindead then you should own ANYTHING to even put silicone on! You wouldnt be able to drive a car or put a seat-belt on, this video is the single most pointless video in history, it should not need to exist as NOBODY should be even half this dumb, anyone that cant use a rubbery glue certainly should NEVER be allowed to breed, I cant imagine how terrifying it is to think people that somehow needed to watch this video could be allowed to have children! Those poor kids! They will never be able to listen to or learn a single thing from their father or mother or whoever it is that is too dumb to use glue. People this dumb shouldnt exist & Im VERY angry that you exist in my world when you dont deserve to, Common-sense is a "human" trait that ALL humans are "Born" with ok? This literally makes you not even human, do u think maybe your mum aborted you & u just never noticed??
Also, WTF do you mean "Like Everyone Else"?? Ive NEVER met ANYONE in my life & never will (besides u & other not even human morons that insanely need to watch the worlds dumbest & most pointless video on "how to use fu*king GLUE!") that couldnt use Silicone! How dare you imply that "Everyone" is this braindead!? I couldnt be more insulted for you to think All my friends & myself are literally the dumbest people in history, like me they dont even know you & your already giving them the biggest insult of their lives?? EVERYONE I know, including my 80 year old grandmother can use Rubber based GLUE without needing to be told how to, just like (Apparently UNLIKE You) they can wipe their own asses & brush their teeth without needing to be shown. Also, you should NEVER be using Silicone or ANY Glue based product, I cant think of ANYTHING I could be confisent that you could use as literally EVERYTHING in this universe is harder to use than Silicone, AKA the easiest thing in the world, so NEVER insult everyone else because stupidly (what a surprise, u had another stupid thought) think they are the most braindead life form in the world. Retard, wtf.
First of all, I am so happy I got trolled, this is the first time I ever got trolled by a real-life internet troll! I have to reply to it. So here goes Mr. Troll.
Well, most people who do not work with or handle Silicone-based products and/or glue do not really know what they are doing. they believe glue = stick it on item 1 and attach to item 2, wait for two minutes and its done.
This is the common sense you must mean to. Using silicone for the prevention of water/moisture into cracks in bathtubs can prevent a lot of monetary loss on account of having to suffer from water damage across your home. I believe you are not a homeowner, as you said, you have been doing silicone since you were 14 - what the hell? you mean you've been working at house renewal since you were 14? I was programming in basic, C, connecting Telnet and BBSs by the time I was 14. Since then I've been pretty good and I still believe that - yes, using Silicone is not a standard operation. When I came across the need in my house to repair the bathtub - I watched an experienced plumber placing the silicone as you said using your thumb and voila, looks like it worked. WRONG. three months later, there was leakage from that exact area. I decided upon myself to perform this simple task as you said, myself. So I bought silicon and was just about to do it as he did when I thought to myself: " Wait, if the expert guy used his skills and Magic Thumb and couldn't get it right, why should I think I know any better?" so I decided to research myself the best way and came across this amazingly good video which showed that using your thumb isn't really the BEST option when it comes down to stopping moisture and water from getting in through your sealing. I hope you saw this video, saw the error in your ways and learned how to seal with silicone in a better and more efficient way - so your customers (and I believe you are still doing this since you've been doing this since you were 14 as you said) will appreciate your hard-worked labor. I would like to also tell you to have a good day, enjoy your life, and keep writing these kinds of comments throughout UA-cam, spreading love and joy to all who read you. This enlightens me and makes me very happy and actually, I even paused my work just to go to your comment and reply back. But, I digress, so, to summarize I think Silicone sealing of housing sanitary items such as bathtubs - should not just be done because its obvious how it should be, but whoever does it, should know the full effects it may have on the house and not just man-handle the silicone with a Thumb because its CommonSense. I wish you all the best of luck and instead of replying to the second comment, I'll just leave this comment here for you to read. Besides, I'm sure your 80-year-old grandmother will be very happy to know this is what came out of her grandchild. I hope you find the best method of silicone sealing you can and be the best silicone sealer there is. Last note, please check your grammar and spell check your comments - not all people have CommonSense to know that "u" means "you", because please remember, "B" "C" "R" and "U" are letters, not words.
Edited: Will not be replying further, I'm too busy working..
@@VirusOfCyrus Congratulations on being so clever. I thought it was a very useful video because I grew up believing that the way to put silicon around the bath was to cut the nozzle small, drag it along the gap between bath and tiles and then use your finger to smooth it. Maybe with a bit of washing up liquid on your finger to stop it sticking. So I learned something even if you feel it was all really obvious.
Your video has been absolutely invaluable! Just re-siliconed our shower, in an almost identical way to what you did here. Bought myself a FUJI kit - wow, what a game changer! Actually enjoyed the whole process thanks to you. No more dragging silicone or concave joints for me! Thank you so much!
Thanks so much for letting me know. So chuffed you aced it. And did you watch this one too do the corners ua-cam.com/video/EErbuodMOAM/v-deo.htmlsi=W9EhrXZdsmi5jYcr ? I could have explained corners better in the original video. 👌👊
Thanks Andy, I’ve had the Fugi ki for years but still opted to spit on my finger. I resealed our shower yesterday following your guide and it’s great. Thanks again
I really can’t thank you enough. I watched the video 3 times, bought all the kit and have just done it this morning. It is by far the best job of applying silicone I have ever done. I was dreading doing it as well but your tips made it really straight forward. Thanks again! Paul
Paul that's the best news! Thanks so much for taking the time to let me know how you got on. Makes doing all of this worth while!
Thank you! I have struggled with silicone for more years than I care to remember, and have probably tried every tool, every trick but never got good results. Fugi kit has been added to my toolbox and all the other crap is in the bin.
Okay, I did it !!!! Probably not up to Charlie’s standards, but far better than the professional who had originally done my shower. I bought the Cramer kit with the blades and handle, so easy to get into close corners to remove the old sealant.
I was dreading that first use, as when I first used the shower post installation it had 2 areas that leaked, and despite a return from the plumber, it was never right.
As I did this on a cold wet October day I let the sealant cure for 48 hours... no leaks. I am so impressed with this tutorial. Thank you.
Jane that's awesome news. I'm so chuffed you've fixed it, and thanks so much for letting me know! 👍
Hi Charlie. Watched this a while back and ordered the set. Went on holiday for two weeks and mentally prepared myself to reseal our shower. Came back and went in all guns blazing. Most stressful few hours of my life. A comedy of errors but made good in the end. Looks ace now - like a brand new shower. Thanks for the pro tips. 🙏🏼🙏🏼🙏🏼
Does it still hold up?
@@Jonas_Aa Yeah still looks great!
Man! This is definitely the most comprehensive and useful video on siliconing the right way. The science and thoughts behind doing a good job you share is priceless. Thanx.
This is an EXCELLENT video! Needed this for recaulking my shower stall. I had just watched another video that did it all wrong, including the soapy water! Glad I found this one.
You're welcome - thanks for the comment 👍
I ordered these tools. Just used them and followed your tips…. OUTSTANDING RESULTS! I’ve never used silicone but I didn’t want to mess it up… I know how easy it is to mess up. This toolkit and your tips gave me the most professional looking results!! I did the vertical corners and where the tub meets the floor in the first day. Second day I did where the tub and tile meet! A+
Brilliant Mark! So glad you aced it, and sounds like you watched my corners vid for the tip about doing the vertical section first. Great work 👊
well done! as an engineer i appreciate these insights
as a pastry baker I also appreciate these insights
As a fireman I appreciate these insights
Just re-siliconed my bath and shower following your steps, so glad I watched the video before I started. Thank you.
That's great news Stuart. Thanks for letting me know!!
Thanks Charlie for a really thorough and informative video tutorial. I was about to spend ages masking up my bath before applying a thin silicone bead and smoothing using my finger. Really useful to know why this is all wrong 😊
showing rather than preaching is brilliant teaching! Demonstrating how voids are created with a finger (ooh er Missus) is priceless and saved me from making similar mistakes. Sorry so many other professionals decried your techniques in earlier videos. Perhaps thy could watch and learn. Thanks for this and all your great videos,
Thanks Chris, you're very welcome. Thank YOU for taking the time to comment. Also check out my corners video ua-cam.com/video/EErbuodMOAM/v-deo.html if you have time as I didn't cover corners that well here.
BLOODY NORAH, by far the best DIY video on anything - not just siliconing. I've been siliconing quite regularly for some 25 years but I will now be using this method. Brilliant!!!
Thanks Guy - LOVE that comment! Get yourself one of those FUGI kits. You won't regret it! Thanks again.
Already ordered one on the strength of your video - you should be on commission! Will check out your other videos in due course!
guy submarinerguy Yes, I definitely missed a trick there! Great stuff - let me know how you get on!
I tend to dip my tool in the washing up liq mix this works sooo much better than spraying onto jointed area. Better control.
bearwoodcarpentry...Does your wife agree that dipping your tool in washing up liquid gives you better control?..or do you continue to spray into her jointed area?
Thanks again for your help and support and help
Thanks
Great video! I'd like to hear more about how you would avoid getting silicone on the inside corner. I think cutting at 90 degrees and pushing would make it more likely to fully fill the joint and seems opposite that goal.
Please don't apologise for going into detail. It's essential, and it's why myself and most of your other followers subscribed to your channel. Great video.
Thanks Dev. It's a constant battle to try and keep each vid as concise as possible. I just think sometimes, if I don't explain my thought process and why I arrived at a particular solution people might not appreciate why this is better than doing it another way. I really appreciate the feedback, and can't thank you enough for supporting the channel 👍
Hi Charlie, superb vid, love the fact that you put effort into researching these things and share your findings. I’ve been doing ok-ish diy siliconing for years but have just re-siliconed a shower enclosure using your tips, tool recommendations etc. with what I can only describe as professional results. Thank you!!!
Excellent video Charlie! I like your detailed and fully explained videos which even explaining the pitfalls.
Your explanations about how using a finger makes thin peelable tapering edges and using tape makes stepped edges are so true and as for the soapy water causing a bad bond (or licked finger that I have heard can cause tongue cancer from the fungicide) - yes, in the bin with those ideas.
This video on silicone sealant was interesting to me because I too discovered those plastic profiling tools and find they make a huge difference and a much stronger joint.
I'm so glad you mentioned filling up the bath prior to caulking a bead as that's something I also discovered after examining why my joints were splitting off the bath side (whilst sat in the bath🤔). It's also important, especially with a thick bead to leave the bath filled for a day or two until the bead is fully cured all the way through to the back corner. That way when you remove the water the joint comes under elastic compression, relaxes when filled again and never goes into tension so won't pull away. If you empty the bath too soon after beading, the still internally soft bread will ooze into a relaxed shape and the surface profile can distort and set like that, but when you next use the bath the joint will be under tension which is what you don't want.
I used to cut the nozzle of the tube at 90° to the desired bead size and press into the joint at 90° or slightly more to push the bead for a very slightly concave surface. Done right it works but you have to be really precise with flow and movement so as not to leave a gap or apply too much that needs careful removal with a knife blade and corners were a pain. These excellent plastic profiling tools do away with all that bother and are so quick there's little chance of skimming over before you are done.
One other thing I'd like to suggest is degreasing with isopropyl alcohol (IPA). You can get it 99.99% pure (5L for
Hi…. This video is Fantastic, especially for those who DIY or are just starting to learn DIY like myself.
I read your comments, and o have recently just put a post on this video, asking if Nail Varnish Remover could be used as a cleaning agent as well as Methylated spirit and Acetone…? Not that I will be using nail varnish remover as a cleanser but more so if you don’t have both methylated sprit or acetone and are unable to purchase any for any reason.
The reason I ask, is because I believe that Nail Varnish remover contains acetone, or acetone can be used as nail varnish remover.
Bought one of the Fugi kits a couple of years ago and they are very good. Along with your helpful extra tips like cutting the mastic applicator at 90 degrees, very helpful 👍
Thank you so much I bought the kit you described and followed your tips. For someone who has never laid silicone before it looks excellent. I had been dreading this job and there was no need whatsoever.
Your right. That process does go against the norm.
That being said, I'm converted.
Well done, keep it going. I've been doing DIY for years and I thought I knew most things, lol
Thanks!!
Thank you, beginner DIYer you should saved me from dozens of rookie mistakes, thank you for not presuming we knew half of the basics (common mistake for usual expert advisors)
What a great tutorial, thank you. Always used my finger as thats how my dad and others i know have used!!! Will invest in a set of tooling for sure...
Excellent - Excellent Video. I’ve installed kitchens & baths for 30 years, and I’ve made every ‘Don’t Do This’ mistake shown.
In the cutting the tip too small department, sometimes it also causes the caulking gun material to curl up and away from the joint.
I often check my guns clearance with a full tube in it, and the pushrod extended so I can find my difficult areas to reach before I start. I keep a nearly empty tube for tight spots like behind the water closet.
I often shape the following edge of caulk tube tip into a cove or 90° so I don’t have to come back with a shaping tool. I cut the leading edge most of the way through with a wire cutter, then shape the following edge with a razor knife.
For tight spots, there is a canned silicone with propellant (Flex Shot) which is great for tight spots and frequent small jobs. The tip is smaller than most unscrewable tube tips and easier to clear.
Thanks buddy. You've got some great tips there. There are also swivel nozzles for getting into tight spaces as mentioned in this video. 👊 ua-cam.com/video/EErbuodMOAM/v-deo.html
I was spray bottle guy aswell. Was the way we were shown. Good results for short periods of time. I am glad to watched your video.. Excellent.
Thanks for your honesty on this mate. You're right - the spray method looks great initially, but what the spray evangelists who have got very angry with my video don't see is the aftermath 6 months or so down the line when the joint starts to fail. They probably don't get many call backs because their customers just assume that silicone is only meant to last that long.
Manual: The surface of Mapesil AC must be finished off with a damp tool, preferably moistened with soapy water, before a superficial film has formed.
Thanks
@@polrze Hi, novice here (me, not you). Perhaps this is a general rule, not necessarily required to be followed with the tools demonstrated in the video due to their material (this is a guess). I also guess that a damp tool shouldn't be confused with spraying the silicone directly. I would guess a damp tool might glide better if it's made of a material that the silicone is likely to grab to, without the adverse effects of spraying directly.
@@craigcunningham9297es, how about a little water on a gloved finger? Someone did that on one of the other videos. (I am also a novice.)
Thank you for explaining everything so well, I'm about to take the plunge and do my bathroom! Am feeling more confident now.
Hope you used the crema silicon kit it’s the best one out there
I've just down my bathroom following your way and it looks great, thank you
Thanks for the video. I´m former sanitary serviceman and now I realized what I was doing wrong.(not cutting the tip to wide of tool and using detergent water) My tomorrow job at customer´s shower corner will be an easy job now. Many thanks.
So glad I watched this video as I was about to do most of the ‘dont’s’ thanks to other videos. Well done on a really well made video
This is by far the best and most informative video I've watched about caulking! Thank you for being so thorough and sharing!
You're very welcome Taralyn. Thanks for letting me know!
Rather than that plastic scraper thing to get the old stuff out, I use a sharp wood chisel. Satisfyingly successful, but it DOES have to be sharp. Great video! I’ve been siliconing for years but still learned a lot from this.
Nice one chum 👍
Hi Phil, thanks for the comment - much appreciated, particularly given how long you've been siliconing for! Yes I can see the merit of using a sharp chisel - you get enough power into it to totally scoop clear the silicone, in a way that you never can with a scraper tool or even a Stanley blade.
I also use a sharp chisel .. works brilliantly
After watching a lot of "how to" videos which turned out to be "how not to" I'm so glad I found your video. You deserve a PhD in siliconing because you've actually applied some science and experimentation to the subject! The "don't make it concave" section was particularly enlightening and makes perfect sense, yet everyone seems to do the concave. I've always questioned the wisdom of soapy water but always got the response "that's how it's done" - now I know I'm not going mad, so, thank you !!
Been joint sealing for 20 years inside and out. I agree with most points and disagree with only a few. Use a sharp chisel to remove old silicon, especially when it's hardened. It cuts through it faster, less effort and last a lot longer than any Stanley blade does like in your video. When time is money and you have to get 10 duplexes done in a day with two full size bathrooms, wash room, laundry, kitchen and entire down stairs if they're tiled swapping out Stanley blades 2-3 times a house is just a waste of time & money, especially when your doing the initial sealing when the grout and tiling glue is jutting in and out of every joint which is how tilers leave it these days.
About the spray bottle. It's the preparation and application of the joint and silicon that matters, if you apply it badly it won't stick whether you use the spray or a spade (what we call your kit thingo) or God forbid your finger. Sprays help make clean up a hell of a lot easier when things get messy to. We've all accidently dropped our bit or let the gun run a little too long in one spot etc and all you gotta do it wipe it off.
When it comes to the spade kit, it's a waste of money for 95% of all applications. You WILL lose them and they just aren't worth it, for just a diyer sure but not on a job site, shit always happens. You won't be using 90% of the other angles on them but it is nice to keep in your truck if youre given it.
It may seem odd but a simple but a spray and a paddle pop (ice cream stick) does the job as good as anything. You can manipulate it to any angle you need, inexpensive you can get a pack of a 1000 in a crafts shop or online for a $2 and you have a constantly supply of you like ice cream like I do XD.
Another trick is with your joints and many others I've seen is you take off the raw silicon with a tool/bit/spade whatever the tool with always leave a wavy look to it like in your video when you show how you do it. Thats obviously because a number of things: tool is worn down in places, tiles arent level across, hand movement, friction etc. What I found that gave me perfectly smooth run was after taking off the initial run (this will sound weird and yeah I've got looks before from clients and supervisors) lick a finger and run it along the joint moderately lightly. Your not trying to push the silicon into the joint you're just smoothing it.
Again as long as you're not using tape or God forbid only your finger then youll be good as gold mate and some of my tips or disagreements only apply to on site working where time is paramount. But preparation and application is the absolute top tip you can give to a new comer not so much technique. But it's better to be good with all three steps.
And if you do sealing alot or as a job. Get a battery silicon gun. I wish I got one sooner but that thing will save your arse when its only just above 5*c in a house or outside and you got a full day ahead of you, it's easy to heat up a silicone tub but its bloody annoying and if gotta keep working then trying to squeeze out cold silicon is a right prick to do all day.
Anyways I typed to much, Great vid.
9
I've never seen "hardened silicone", didn't think that was possible.
Awesome additional info .. Thanks
Best tutorial ever! Thanks for the work you put into this.
I do an absolute shed load of siliconing at work, fitting kitchens and bathrooms etc and although I don’t have this specific fugi tool kit I do have another variant. After watching this though I’ve just ordered one as I like the attachments for them. Once your used to them you get just as quick with the formers as u would just using your finger trust me! Great video👍
Marc Gray Thanks Marc. Great comment, and it's nice to hear from a pro siliconer who is open minded enough to use a profiling tool and to acknowledge the benefits of the FUGI. I get a few old school finger siliconers commenting who just cannot accept their technique is flawed and outdated! Thanks again.
Not a problem matey... I’m 27 and always looking for new ways of doing things... upset the older ones! don’t get me wrong some old methods of doing things really are the best, but not in this case!
Marc Gray y
I watched this video after my first botched attempt at siliconing around my new bath. I bought the Cramer kit and with a bit of care and following Charlie's advice my bath seal now looks great. The cramer tools are a cinch to use, even for a dolt like me. Get the profiling kit 7 that comes with the scraping blade tool - it's marvellous!
So pleased to here that Scott. Excellent work and thanks for letting me know how you got on. 👍🏻
Thanks! This kit worked exactly for me as it did in this video..... and it was my very 1st shower / silicon job - ever.
I watched your video. I took your advice ...and the job turned out perfectly. Thanks!
Well I feel humbled because I have been doing this for a long time and your methods are brilliant and now my new methods ! Thanks for the video....
Thanks Marcus - I really appreciate that!
I have been a handyman for years and own my own maintenance business , sad to say I was taught the completely wrong way by another tradesman. Just purchased a set of profiling tools :)
Questions please
Lol
Finally someone who took the time to show how it's suppose to be done. Will be doing a kitchen renovation and installing backsplash now I know how to do better than most professionals that just use fingers and tape. Thanks
Thanks Lucio, and if you have any corners to do, check out this vid ua-cam.com/video/EErbuodMOAM/v-deo.html
Hi Charlie, thanks so much for this. I've been a finger-bodger for years but have now seen the light. Subscribed.
Thanks mate. Really appreciate the comment and the sub!
@@CharlieDIYte No problem - as @DAVAD M DAVAD said, I appreciate the proof you supply with your logic. I have a problem that I hope you can help me with, though. I can see the benefits of using the FUGI Kit where the top of the bath is flat and at right angles to the wall. Do you have any tips for coping with a bath that has a raised shoulder before it drops down again to meet the wall?
"-Don't use tape"
"-Don't use fingers"
DAMNIT DAD! That's was the two advices he gave me!
It's SO annoying when you find out your parents were right. Again.
@@bluesky7838 No, he gave the opposite advice.
And the tape just got in the way.
@@slitor oh, right. I mis-read.
This is a very good guide to do a quality job. However everybody has their own methods of doing things that have some variations. I have caulked hundreds if not thousands of shower/tub surrounds over the 35+ years of owning a solid surface company and many of the caulking jobs I've done have lasted for 20 years or more.
To add my 2¢ into the equation, if you follow this guys method you will get a good result, however I would refrain from using any acetone. It leaves a residue which over a short period can result in an adhesion failure and soon turn black from mold and goo. Use the Denatured Alcohol. I used an industrial spray bottle, it allows for applying a mist instead dumping it out of the can. Industrial spray bottles can be found at most hardware stores, they are usually dark grey. The standard Windex bottle trigger pump will fail quick from the alcohol.
Next, I recommend removing all/any old silicone. There is a reason that you're replacing it and why chance having it fail because of an existing issue. It can be very time consuming to do but the key is to have it last.
Then, once you have got the joint/crack cleared of any bad/existing material clean it good. Use the Denatured Alcohol to prep the surfaces for good silicone adhesion. Spray the areas with Alcohol Just mist them wet not drenched and use white paper towels as wipes. Do not use towels with fancy colored patterns on them as many times the ink will bleed and leave a slight hue to a finished job. Let the ares sit for at least an hour to completely dry. Alcohol does dry quick.
Apply the silicone as instructed in the video plus only do about a 2 foot stretch at a time because if the silicone starts to dry (even slightly)it will develop a "skin" and it will pull the bead and make tooling difficult. Now the guy does make an extremely valid point about getting good penetration into the seam and full adhesion without gaps or bubbles in the caulk is important, although if it happens you can always spot fill.
Tooling the joint. I have use the fancy caulking tools he shows and they do work well, but if you are doing this just one time save the $10 - $15 and go over to the kitchen department and grab a few of those Formica chip color samples. I used those for years. You can use them as they are or sand down the corners to make any profile you want. Plus they are thin and make tooling a corner easier then a thick tool. Regardless, either works well. I've even used my finger on a lot of jobs, just make sure they are clean first.
Now the biggest difference with my final method is how to do the tooling. After running my silicone as smooth and without voids, I use the alcohol spray bottle to lightly mist the bead before I touch it. They guy is right about not using soapy water, Only use alcohol. Besides silicone is waterproof even before it dries. The reason for this is because you want no silicone to stick anywhere but where you put it and to just tool it dry can lead to it smearing and leaving a minute film that can eventually peal and possibly affect the finished bead over time. Also if you get some silicone somewhere accidentally, the alcohol with a paper towel makes it easier to clean up. Now, even the best professionals don't always do the job without a spot or two that the silicone didn't stick well or came out of while tooling, so just allow the alcohol a little while to dry and go back and spot fill.
My biggest piece of advise when you do any silicone work is to keep it clean. Always have at least a full roll of paper towels within easy reach and an open garbage bag to throw them in. Don't skimp on the towels because once you get silicone anywhere other then where you want it then you've got a nightmare (cleaning silicone finger prints is not fun).I never liked using rubber gloves doing this because you lose the feel of the small areas. It doesn't take much to go everywhere and clean up (especially once it dries) can be labor intensive. Also wear clothes you don't care about because this stuff won't wash out.
Terry Dillon You give some great tips, but I must say in Charlie’s defense he did cover some of them. In regards to caulking over caulk (silicone), the caulk that he was caulking over was in great shape. You are correct though that one should never caulk over moldy or dirty caulk. That’s just gross and disastrous. I do appreciate your wealth of information. Thank you for sharing :) Between you and Charlie I’m ready to tackle my project.
Methylated spirit IS denatured alcohol. We colour it purple in the UK to deter homeless people from drinking it.
@@louised6790 Many times when there is an issue of mold or contamination most of it is usually behind silicone that appears perfectly sound. Many times as I have removed existing sealant, mold and such are exposed on the back side of the bead you are removing. The contaminants in most cases work their way out from behind the surface instead of from the surface inward. I believe they are caused by a failure or void in a small location and as moisture penetrates it does not dissipate deep inside the bead and the contaminant remains and leads to future failure, hence the need for frequent spot repairs.
Terry Dillon YIKES! That makes total sense. I actually knew but it didn’t dawn on me in this instance. Well I feel silly! Thank you for bringing that to my attention. I’m getting ready to tackle a shower where they laid a grout line between the tile wall and the tub and they did it again outside of the tub and the tile flooring. I haven’t had a problem at the floor but the grout inside the shower in molding. I can’t believe they did that! I’ll keep my eyes peeled for anything deep inside.
@@louised6790 Once you get all the horrible gunk Out Karen, make sure to go at it with a 'Hard' Level Toothbrush (or any old ones you've got laying about !) And give the Whole area a really good Disinfectant Clean - evening time, before bed is good for leaving it 'overnight' ! As I expect you're like myself - once Started, don't Stop !!
After a lot of years, It dawned on me - like one of those new LED lights ! - that I was Missing things, or promising to get Back to Bits, that weren't quite right ! In order to be Finished !
Due to Chronic illness I can't do Any of the DIY things I used to, but it Pains me to watch some
(¥£€¥₩) take 2days to paint & wallpaper a room - things I used to do (start to clean up!) In a Day and a Half !
But, as my wife pointedly remarked after a few moans about "so-called Pros"! That THEY had Working Hours, which meant they, unlike me, didn't get finished at 5am, or go to bed reeking of White Spirit.!!
So, do What you Know you Can do, and get someone in for the Stuff you Can't !
Or another good trick is to offer a "helping hand" because you really want to see How to Do It, because you're thinking of taking a Course !
Most of All....Be Proud...🤗.
Of What You've Already Achieved !👍
HOPING 2019 BRINGS U & Urs:
PEACE✌HEALTH💛
&😊HAPPINESS😃
🍀POD🖖
What's excellent about your presentation is you give the reasons behind every point. The explanation of how the pre-application of soapy water prevents a good bond was especially helpful. Thanks!
Thanks I really a appreciate that and there's a corners video you ought to watch too ua-cam.com/video/EErbuodMOAM/v-deo.htmlsi=1aj_63S5icyshxso 👊
I'll admit I've done nearly all of those things you shouldn't do when applying silicone.
And this video is beautiful.
Aw, thanks mate!
Incredibly well done in content and form. Brilliant work on a common task. Thank You!
You're being welcome Mark - massive thanks for the comment!
Charlie, thank you so much for sharing your great knowledge! I used the Cramer Pro Guide and got perfect results. Again, thank you for sharing! Best regards, John Ellis. Aldie, Virginia. USA
Hi John, I'm blown away that my little vid has reached as far as Virginia. So glad you found it useful and I can't thank you enough for taking the time to comment - it's what keeps me doing these vids 👍