In 1:51, please describe how to use these screws. I want to add a little bit more water with every fill-up. Which screw do I turn and which direction? Thank you for the video. Very helpful.
No frost refrigerator, direct cool refrigerator, deep freezers And many more, Can't explain the cooling system on comment, it is a lengthy topic. Will make a video on it in future.
what do the three adjustment screws near the terminals do. I.E. what happen if you turn the very centre screw anit clcokwise ? etc can u expalin please
Should any of the rattle when you shake them? I am researching the one at 5:03 with three terminals. Should the reading not change when pressure is applied? Like continuity from 1 and 3 should switch to 1 and 2 or 2 and 3?
Excellent!!!!! This would explain part of the 4C error code which is not filling; if the water level sensor is damaged, then this will cause the machine to automatically drain and stop operation, let alone if the machine has been restarted so many times, it will overfill. This is basically like having an EFI for washers. Learned the hard way with my Samsung Machine.
That would have confused me hunting for a switch when in reality, there is a variably resonant tank ... ie f = 1 / (2π × √(L × C)) ... thanks for that info!
Yes the motor works after the water level in the drum reaches a level you selected. The water pressure stops the water inlet valve to flow water. And the motor receives signals to work. And start the wash process.
@@forevertechenglish just want to make sure please. Is one of the 3 wires on the pressure switch send signal to motor to wash. Not a wire on water valve?
@@forevertechenglish yes that i know, but isnt the pressure switch give the signal to the circuit board after closeing the water valve. If the pressure switch not close the water valve. The circuit board will not get a signal to wash motor. Isnt it?
Yes, What you said is correct, first the pressure switch send signals to the circuit board. and the circuit board closes it. Then the circuit board sends signals to the motor to operate.
very nicely explained. Good job. My siemens 7kg fully automatic front load wash machine is 13 years old. The problem with it is - now it is always complaining about low water pressure with F17 error code. I checked the water pressure from inlet pipe. It looks good pressure to me. Any thoughts on what could be the problem sir?
The Water tray could have dirt or soap scum which is blocking the water, as I have experienced it, Clean the tray, Check for blockages in the water pipes, clean the filter attached with the water inlet valve. And I think the problem could be resolved
@@forevertechenglish sir appreciate your quick reply on this. I figured out the problem. As you said i opened and cleaned the soap tray. But the actual problem was in the water pressure here in my top floor flat. Since this is top floor, there is very less water pressure at the inlet of washing machine. Hence I added a pressure booster pump.
I have Samsung washer .. the problem is not stopping filling water . I changed the water inlet valve and still not working . So when I disconnect power the water shuts off . What do you think ? It may be the water pressure sensor ?
@@johnxu6477 so I tried to do the washing cycle test ( washing and spinning) and it went well . But I use normal wash or quick wash the water keeps filling with no stop . Did you try to fix yours ?
Very well explained, I'm not into electrical stuff at all, but after a explanation like this, even my child will be able to do it.
Thanks Man
Great video with clear explanation and demonstration - thank you!
Glad it was helpful!
thank you from Uganda Kampala Africa
OMG, such a good explanation!
Excellent explanation for washing machine level switch details
@@AbdulRashidGhulam thanks
In 1:51, please describe how to use these screws. I want to add a little bit more water with every fill-up. Which screw do I turn and which direction? Thank you for the video. Very helpful.
I'll watch all your videos!
Thanks
Beautiful explanation. Thanks a lot.
I am glad you enjoyed it!
Very informative and clear... Tq
Thanks alot, I am glad It was helpful.
Well explained👍
Thanks so much. Very Very useful.
Teşekkürler hocam. Sevgi ve selamlar.
Excellent explained
Glad it was helpful!
Thank you for explaining the topic in english 👍
GREAT EXPLINATION.
Nice and apricated your all videos but last time I asked you to tell me about types of refrigerator and the way how to cool tnx for your help
No frost refrigerator, direct cool refrigerator, deep freezers And many more, Can't explain the cooling system on comment, it is a lengthy topic. Will make a video on it in future.
what do the three adjustment screws near the terminals do. I.E. what happen if you turn the very centre screw anit clcokwise ? etc can u expalin please
Should any of the rattle when you shake them?
I am researching the one at 5:03 with three terminals.
Should the reading not change when pressure is applied? Like continuity from 1 and 3 should switch to 1 and 2 or 2 and 3?
Good luck sir 🎉
Thank you for your very good explanation.
You are welcome!
Thank you very much.
You are welcome!
tyvm for sharing this. great explaination
Glad it was helpful!
Good ,thank you for all
Excellent! If coil resistance is approximately 21ohm, between 1 and 3, is it ok?
Hello thanks for this informations are very important good job thanks 🙏
Glad it was helpful!
Grate video
thanks sir for sharing,God bless.
Always welcome
What 330mf capacitor do in there
What value are the capacitors? Interested.
Thanks
Welcome
Thanks a lot Bhai
This's so good man you've explained very well thanks man.
Glad you liked it!
Great video,just one question,my washing machine's water level changed for some reason on one cycle,do you maybe know why?🤨
How did it changed, I didn' got what you are trying to say, can you explain how did it changed.
Clear info
Amazing
Thanks
Excellent!!!!! This would explain part of the 4C error code which is not filling; if the water level sensor is damaged, then this will cause the machine to automatically drain and stop operation, let alone if the machine has been restarted so many times, it will overfill. This is basically like having an EFI for washers. Learned the hard way with my Samsung Machine.
But this basically work with air pressure, and adjust the level of the water accordingly
Maestro.
Thanks sir
where to buy 2 wire haier sensor?
You can buy it from haier service center.. If one in your city.
@@forevertechenglish jazakallah
That would have confused me hunting for a switch
when in reality,
there is a variably resonant tank ...
ie f = 1 / (2π × √(L × C)) ... thanks for that info!
Wery good.welcome you
When pressure sensor switch close water inlet valve is the pressure sensor switch wire switch on motor to wash?
Yes the motor works after the water level in the drum reaches a level you selected. The water pressure stops the water inlet valve to flow water. And the motor receives signals to work. And start the wash process.
@@forevertechenglish just want to make sure please. Is one of the 3 wires on the pressure switch send signal to motor to wash. Not a wire on water valve?
No, the signals are passed through the circuit board.
@@forevertechenglish yes that i know, but isnt the pressure switch give the signal to the circuit board after closeing the water valve. If the pressure switch not close the water valve. The circuit board will not get a signal to wash motor. Isnt it?
Yes, What you said is correct, first the pressure switch send signals to the circuit board. and the circuit board closes it. Then the circuit board sends signals to the motor to operate.
👌
1:54 got em
very nicely explained. Good job. My siemens 7kg fully automatic front load wash machine is 13 years old. The problem with it is - now it is always complaining about low water pressure with F17 error code. I checked the water pressure from inlet pipe. It looks good pressure to me. Any thoughts on what could be the problem sir?
The Water tray could have dirt or soap scum which is blocking the water, as I have experienced it, Clean the tray, Check for blockages in the water pipes, clean the filter attached with the water inlet valve. And I think the problem could be resolved
@@forevertechenglish sir appreciate your quick reply on this. I figured out the problem. As you said i opened and cleaned the soap tray. But the actual problem was in the water pressure here in my top floor flat. Since this is top floor, there is very less water pressure at the inlet of washing machine. Hence I added a pressure booster pump.
So if the terminal 2 and 3 gives a reading that mean the pressure switch is faulty .the one for top loader with three pin.
Also want to know 🤔🤔🤔
I have Samsung washer .. the problem is not stopping filling water . I changed the water inlet valve and still not working . So when I disconnect power the water shuts off . What do you think ? It may be the water pressure sensor ?
same issue here
@@johnxu6477 so I tried to do the washing cycle test ( washing and spinning) and it went well . But I use normal wash or quick wash the water keeps filling with no stop . Did you try to fix yours ?
Same company same presure switch using
So these are basically LC circuits?
LG washing machine filter where is it?
Saan po pwedeng bumili ng water level
Hi sir, can you tell me about the main board cold water is not lightning only hot water ligthning what is the problem?
Which Washer is it?
I measure frequency are 25.xx khz durung no water pressure
Yes... see deez nutz! lololol
hahahhaha,
1:54 came to comment this 😂
@@ydnar71 These are screws, I got it wrong, Lol..
Can you give me an explain for my laundry Samsung that take water unlimited , without end, what can happened with my laundry...?
Check the water pressure switch or the water inlet, fault they might be faulty.
@ 154 See deez nuts
IMMEDIATE DISLIKE for the use of that AI voice. Shame, because the video itself is good.
Very helpfull thanks
thanks