410A needs to have the bottle inverted upside down to charge properly as a liquid. If you charge it upright, it will fractionate the near-azeotropic mixture. R22 is a single component and can be charged as a gas.
R410A and R22 is two different types of refrigerant (Gas). R22 is older type refrigerant and R410A is modern refrigerant. R410A is more environmental friendly than the R22 refrigerant. Because R22 has chlorine atoms which dangerous to ozone layer but R410A doesn't have any chlorine atoms. The modern AC systems are replacing the R22 refrigerant with R410A refrigerant. R22 Refrigerant will not be available in the future due to environmental concerns.
@@DaveMavrik-ki7xb R22 and R32 are single refrigerant and their composition does not change. Thus both liquid charging and gas charging is possible. Liquid charging of R32 all at once from the low - pressure side may cause the compressor to malfunction. Working pressures for R32 are very similar to R410A and when charging, R32 is easier to handle as it can be charged in both a gas and a liquid state. This why R32 is classified as A2L “mildly flammable” while safety data sheets say it is extremely flammable but it really is very low flammability.
The low-pressure line is typically used for charging refrigerant gas, whereas the high-pressure line is used for charging refrigerant liquid. Liquid charging generally takes less time compared to gas charging.
This is a very good video. Please my question is I added refrigerant to my 1hp Samsung spit AC when the power was turned off and I waited 10 hours to put the power on. Is it okay?
If we open the High Pressure On/Off Valve, Refrigerant will start going from AC Unit to Refrigerant Cylinder. Because the pressure in the High Pressure Side of the AC Unit is more than the pressure in the Refrigerant Cylinder.
No you can't fill through the red hose. Because the red hose in connected the high pressure side. If you try to charge through the red hose. Instead of the refrigerant going into the unit, the refrigerant will return to cylinder from the unit because of the pressure difference.
Hi, thanks for the video. Is it necessary to attach the red hose to the air conditioner in order to fill it? I have simpler manifold gauge, with only blue and yellow hose (without red hose, and without red gauge).
Brother it's totally half knowledge about gas charging it's not the way we have to first leakage check and fill leakage than vaccum after all process gas charging 😊😊
No vacuum pump, no scales, not even a drop of environmental protection. We do not flush with refrigerant!!! The other is that it is not possible to connect to the discharge line. Sorry, but this is how don't do that.
@@ujjawalkamboj2965 Yeah sure, in this channel I will upload only English video. I have opened a separate channel for Hindi. In that channel I will start to upload videos in Hindi.
You tell everything about gas charging step by step . Now No question is remain .
Full guide 👍💡
I am glad. But there are many things about refrigerant charging. I will explain everything in a video.
@@zebralearnings oka sir I will be wait 😊
Suchionline contened dis ..chergd lind contactinv yelow chwfgjnv cylinder valvropon cylindef R420 cylimdef up fosn anc cherhrinv ues fighte allthsnkyou gues wdlcome purgdaftef yes testing fixing checkinv znd oneby meghec ok
@@zebralearningscan I get ur number
410A needs to have the bottle inverted upside down to charge properly as a liquid. If you charge it upright, it will fractionate the near-azeotropic mixture. R22 is a single component and can be charged as a gas.
What is 410a? What is r22?
It's depends on the cylinder. Before charging the refrigerant we should check the instruction on the cylinder how to charge.
R410A and R22 is two different types of refrigerant (Gas).
R22 is older type refrigerant and R410A is modern refrigerant.
R410A is more environmental friendly than the R22 refrigerant.
Because R22 has chlorine atoms which dangerous to ozone layer but R410A doesn't have any chlorine atoms.
The modern AC systems are replacing the R22 refrigerant with R410A refrigerant.
R22 Refrigerant will not be available in the future due to environmental concerns.
Does r22 and r32 also need to turn the cylinder upside down too?
@@DaveMavrik-ki7xb R22 and R32 are single refrigerant and their composition does not change. Thus both liquid charging and gas charging is possible. Liquid charging of R32 all at once from the low - pressure side may cause the compressor to malfunction.
Working pressures for R32 are very similar to R410A and when charging, R32 is easier to handle as it can be charged in both a gas and a liquid state. This why R32 is classified as A2L “mildly flammable” while safety data sheets say it is extremely flammable but it really is very low flammability.
Nice explanation sir 👍thank you
Always welcome 😊👍
The low-pressure line is typically used for charging refrigerant gas, whereas the high-pressure line is used for charging refrigerant liquid. Liquid charging generally takes less time compared to gas charging.
Hi. Why need to connect high pressure line if we are not use that during charge refrigerant?
What a man you are very grateful 💓
Thank you for this good animation! 👍🏼
Thank you
Brdr how can we connect valve in high pressure and low pressure units?
What is the need of connect high pressure guage????
To know High pressure
To get readings of sub cooling
This is a very good video. Please my question is I added refrigerant to my 1hp Samsung spit AC when the power was turned off and I waited 10 hours to put the power on. Is it okay?
Can you show other techniques? Please
Yeah, sure. I'll upload.
Could you explain to me what happens if we open high-pressure on-off valve when we charge refrigerant ( GAS ) in an AC UNIT ?
If we open the High Pressure On/Off Valve, Refrigerant will start going from AC Unit to Refrigerant Cylinder. Because the pressure in the High Pressure Side of the AC Unit is more than the pressure in the Refrigerant Cylinder.
@@zebralearnings I have always charged a AC system with high and low side
can you fill using the red hose to the low pressure side?
No you can't fill through the red hose. Because the red hose in connected the high pressure side. If you try to charge through the red hose. Instead of the refrigerant going into the unit, the refrigerant will return to cylinder from the unit because of the pressure difference.
one question, is the red hose to high pressure line, complete shut off all the process?
Yes, it will be completely shutoff through out the process.
why have it connected then? can't you just have the blue hose connected to fill ?@@zebralearnings
Please i want to know using my single guage, on the PSI scale, what number should be the jogjest I'll let the gas reach in a 1.5hp inverter AC
A very helpful tip is to add 50ml of purified water to the compressor before regassing. This reduces corrosion and no need to vacuum
How to know when its time to close the blue vlv after letting air out
Nice question. You can see that easily when the refrigerant comes out. It will come out like spraying water.
Pls produce video about electrical connections.
Hi, thanks for the video. Is it necessary to attach the red hose to the air conditioner in order to fill it? I have simpler manifold gauge, with only blue and yellow hose (without red hose, and without red gauge).
Very good sir ji....exvelenttt
How do we know how much gas need to be refill
We can check that with the pressure gauge.
Please i need more information about Refrigeration and ac
I m instrctor r/ac..but your mathed very Excelent.......
very clear video🎉🎉
Glad to hear that
How i know that i charged enough gas? What is the right pressure i looking for?
Nice video
Thank you 😊
new friends please friends me
Thanks a lot very usefull ❤
How much refrigerant should charge
please tell us before charging gas required vacuum full machine required time and -psi value
Don’t you usually charge with the jug inverted ? Liquid not vapour
How much time will it take to transfer gas from cylinder to ac outdoor unit
How to use claim meter to recharge
Why discharge valve on guage was closed thought-out
THANK you
You're welcome!
This is not discharge line,it is liquid line.Its after the condenser and before the expansion valve.
I was charging 410a while charging compressor and fan shut down itself, I checked breaker and thermostat both were on , what could have gone wrong
Thanks !
Why does nobody ever show you what you do if you have a recovery cylinder I don’t know whether to hook it through the red or the blue
Very good
Thank you
And unit offff what is prociger
Sub presiune manometre control valve
Brother it's totally half knowledge about gas charging it's not the way we have to first leakage check and fill leakage than vaccum after all process gas charging 😊😊
It's just a basic concept of gas charging method. I'll make a detailed process of gas charging video and will upload it.
Nice
Thank you
Gas charging ka Hindi me animation
I will upload soon.
bravo
Thank you 😊
👍👍👍
👍👍👍
Should shut down the unit en perform a vacuum test 24 hours prior charging the system to be sure the system is leak free and all the air is out.
In hindi translation plz
I am making in Hindi also. I will upload soon.
রিদয় নাড়া দেওয়ার মতো একটি নাটক।
My name is teja
THis is for Brampton boys not the proper way thanks but no thanks
Soon, I will explain it detailly..
WRONG NEED SCALE,AFTER VACUUMING R410 OR R32 IN LIQUID STATE BEFORE RUNNING THE SYSTEM WITH EXACT WEIGHT.NOT OLD SYSTEM YOU ARE TUTORING.
Hi
No vacuum pump, no scales, not even a drop of environmental protection. We do not flush with refrigerant!!! The other is that it is not possible to connect to the discharge line. Sorry, but this is how don't do that.
Hindi video
main hindi video bana raha hoon aur jald hee upload karoonga.
Please continue in english
@@ujjawalkamboj2965 Yeah sure, in this channel I will upload only English video. I have opened a separate channel for Hindi. In that channel I will start to upload videos in Hindi.
Very good