Sir, I have to say thank you so much for an excellent video you showed step-by-step how to put together the entire throttle cable. I’ve been looking for a video all day and yours explained it fantastic and you took your time. Thank you thank you thank you you should be the only one on UA-cam, making videos for go kart and dirtbike engines
Hey, I put on a new throttle cable and bike wont start. I remember there being a clear plastic piece covering the cable on the carburetor end. Do u think that's the problem?
So listen I need a little help bro… I got a pwk 21mm and I need it to fit the 13mm 80cc port with a boot..anyone know what I can get to make this happen or work?
Where can I buy a throttle kit for my 50 I have been looking and almost every one I buy does not have that spring and needle at the end where can I buy?
I tried this two years ago on a JAWA 50cc and it was a diarrhea mess. I assembled and disassembled it like four times and it simply WAS Not right. The throttle cable was like real loose and didn’t snap back after a twist. It was just an assAnine diahretic mess for me. MMmmmmmmmmmm, mmmmmmmmmm
I had to rotate the part under the spring it wasn't aligned with the pin as showed in the beginning of the video I thought it was but I was aligning it with the wrong part
Sir, I have to say thank you so much for an excellent video you showed step-by-step how to put together the entire throttle cable. I’ve been looking for a video all day and yours explained it fantastic and you took your time. Thank you thank you thank you you should be the only one on UA-cam, making videos for go kart and dirtbike engines
Thanks man I realized after watching the video that I installed that grey piece upside down you saved me like 2 hours of tinkering tysm
Not bad bro. I know how hard it is to work on something and hold it in focus at the same time. I could see what you were doing clearly. 👍
Thanks man , it was not an easy task 🤣
Thanks very much... I didn't know there was a small point inside the carburator to match where the cable lock
Helped out a bunch. Thank you
Thank you very much on the segment about installing a throttle cable. That's a 5 star plus bonus !
Good video been trying to find a video to show me how to replace throttle cable on cam am ds 70 and this helped. Thanks
Thanks for this video, man. I didn't know what I was doing, but this really helped me.
Thanks bro, this video just saved me a long day
Thank you! I actually needed to learn that
Thank you Sir, certainly helped me finish my project
Great video: looks like you got it! Expert!! Great video man
awesome video i liked and subscribed
Life saver man
Very helpful .. EXACTLY what I needed ..... GD Tractor
I tried to do this for 5 hours on my DT50MX before I found this video and fixed it after 3 minutes😂
Thank you.
Thanks!
Hey, I put on a new throttle cable and bike wont start. I remember there being a clear plastic piece covering the cable on the carburetor end. Do u think that's the problem?
I Just need to get the end that rond thing off but help
There's a little piece that goes on top of the carb that I didn't show in the video
Thnxxxxxzzzzzzz❤❤❤❤❤❤❤❤❤❤❤
So listen I need a little help bro… I got a pwk 21mm and I need it to fit the 13mm 80cc port with a boot..anyone know what I can get to make this happen or work?
Where can I buy a throttle kit for my 50 I have been looking and almost every one I buy does not have that spring and needle at the end where can I buy?
Amazon
I'll try to find a link to it for you
@@icft6183 thank you
I assembled like in the video but my dirt bike just low idles and doesn't have any power and then will just shut off. Any idea why this might be?
Adjust your tic over screw
What happens if you don’t slide it into the little groove
I tried this two years ago on a JAWA 50cc and it was a diarrhea mess. I assembled and disassembled it like four times and it simply WAS Not right. The throttle cable was like real loose and didn’t snap back after a twist. It was just an assAnine diahretic mess for me. MMmmmmmmmmmm, mmmmmmmmmm
Same thing happened to me how do you fix it
I had to rotate the part under the spring it wasn't aligned with the pin as showed in the beginning of the video I thought it was but I was aligning it with the wrong part
Did ya fix it ?
awesome video i liked and subscribed