Great job. Im not a mechanic either and I enjoy doing projects like this. Sometimes can be frustrating when you run into a problem here and there. I’ve learned that one project always turns into 5 other project. Next thing i know, I have a new stereo, new accessories, new headliner etc.
Looks nice, maybe it was the angle, but the SES and information center lights seemed a little fuzzy behind the stainless steel. But seems like a fairly simple mod, the stock GM setup is ultra cheapo and dim, so I guess I will probably try this out.
I'm alittle confused about the needle locations. Before you take the cluster out so you turn the key to accersry and then mark where the needles are at and then turn the keys off?
it seems like you could just lay the new face right over the stock one, seems like they would make it that way. looks good though, i will be doing the same.
Man you are lucky that yours has the replaceable bulbs and is generally just easy to customize Mine has the bulbs soldered on I’m not too good with soldiering circuit boards
How well do the needles glow at night? I have a different stainless steel gauge face and it doesn’t allow enough light to make the needles glow. Plz lmk
The blue needles with the aftermarket blue lights are not the best combination. I switched back to the orange needles and they look much better. But keep in mind that's with the blue LED lights. Not sure if you plan on both mods or not.
Hey bro great job i got the daytona white face but my question is how did you re-install the needles and take them out as im afraid of doing them and they wack out?
I changed my lights to the same LED lights but now they flicker and sometimes turn off for a few minutes have you experienced this and off so what is the remedy
After doing this. it looks great, however my internal turn signal indicators and cruise indicator no longer light up, even though the cruise control does work and the external turn signals flash. Been trying to run down a fuse but can't find one that's blown. Ugh so close
The bulb(s) for the warning indicators are probably burned out. If you decide to replace them, I would suggest to replace all of them. There are two different sizes . . . * Warning Indicators - Qty. 4 - Halogen Bulb - 74 or 2721 - LED Bulb - T5 - 3/8" Socket * Needle Gauge's - Qty. 6 - Halogen Bulb - 194, 195, 168 - LED Bulb - T5 or T10 - T10 sockets Hope this helps!
What tools did you use to take out all 4 screws? I have a small one i can take out the top 2 but the bottom 2 i can't do anything to because theres no room.
Medrano_ 59 if you don't have it yet look for a 1/4 extension. Or whatever size rachet you're using. Home depot should have them. If not either Sears, Lowe's, or Ace should have them as well
My Tahoe was a PPV (Police Pursuit Vehicle) before I bought it. It says Certified under the MPH and it goes up to 140 m.p.h. I've only picked it up a lil over 130 MPH. Tahoe is a beast anyway, it's been hard to find one for mine. Can Anyone help me finding one or a place that can make me a custom one. If not maybe I'll go with one of this but i wanna keep searching before I give up. Thanks and I will highly appreciate it 👍
So I installed this on my 02 avalanche but when I turn my truck on, the fuel and oil needles go way below the zero mark and won’t go up. Neither will the RPM and MPH needles
only if your battery is giving you issues. you can check your battery voltage with a multi-meter. if your battery is acting fine, then you need to check the alternator. To check your alternator, first, open the hood and start the car. While the engine is running, remove the negative cable from the battery. If the vehicle stalls or dies, the alternator is likely bad
You can buy one for your ride on Amazon - amzn.to/2FvkNXv
Great job. Im not a mechanic either and I enjoy doing projects like this. Sometimes can be frustrating when you run into a problem here and there. I’ve learned that one project always turns into 5 other project. Next thing i know, I have a new stereo, new accessories, new headliner etc.
i'm the exact same way.
Can you tell us where to get the stainless steel can you throw in the website
I really like how you make your videos. simple and clear but very informative with no bullcrap but still entertaining. keep it up!
You gave your self a quarter ofgas doing this mod awesome
LOL
I seen that to. Made me wonder if something went wrong.
Is there a way to change the color of the odometer?
How do you change color of gear selector
Looks nice, maybe it was the angle, but the SES and information center lights seemed a little fuzzy behind the stainless steel. But seems like a fairly simple mod, the stock GM setup is ultra cheapo and dim, so I guess I will probably try this out.
I have an 05 avalanche... I gotta do this. Thanx for the direction.
I'm alittle confused about the needle locations. Before you take the cluster out so you turn the key to accersry and then mark where the needles are at and then turn the keys off?
Looks clean. Great video!
thanks!
This is dope. Gottah do this to my Silverado
it seems like you could just lay the new face right over the stock one, seems like they would make it that way. looks good though, i will be doing the same.
No. You have to move your needles to the new face.
You are correct
you just saved me 150$ .Thanks brother 🤘🤘🤘
Man this is one beautiful gauge face you have bought and installed on the vehicle. The silver aluminum is likely a good fit for it. 💯
Thanks 👍
Came out good. Great job
thank you
Got a link for parts ?
So glad I found your channel.
Thanks for watching!
I went on super bright led and they don’t list the blue led dash lights any more.
Man you are lucky that yours has the replaceable bulbs and is generally just easy to customize
Mine has the bulbs soldered on I’m not too good with soldiering circuit boards
Looks amazing though
It's been a long time since I did this, but I did resolder them at some point after this video.
Found my next project “ thanks
I clicked the link but it’s showing me the ones with transmission temp I’m trying to find the same exact one you had
How well do the needles glow at night? I have a different stainless steel gauge face and it doesn’t allow enough light to make the needles glow. Plz lmk
The blue needles with the aftermarket blue lights are not the best combination. I switched back to the orange needles and they look much better. But keep in mind that's with the blue LED lights. Not sure if you plan on both mods or not.
@@TahoeSteve thank you! I’ll probably go with the white leds and see how that’s do.
Does the PRND321 screen illuminate in blue also? I cant tell if its blue or still green. Thank you.
strong work sir
Looks good. Looks like they dont sell it anymore on your Amazon link. How much did you buy it for?
Try this. www.usspeedo.com/
@@TahoeSteve thank you
We're can I get this gage
I have ah 01 chevy hd cluster where can i find the bright blue lds
www.superbrightleds.com/
Hey bro great job i got the daytona white face but my question is how did you re-install the needles and take them out as im afraid of doing them and they wack out?
i just followed the directions that came with it.
How much to do mine or to send me one? 2003 tahoe
How did you get the needle removing tool?
came with the kit
great job !
thanks!
I changed my lights to the same LED lights but now they flicker and sometimes turn off for a few minutes have you experienced this and off so what is the remedy
It's been a while but I think I eventually soldered them to the board and have not had a problem since.
Wish they made these in kmh.
give them a call, maybe they do ??
Is that blue or aqua blue
It's really hard for me to find the cluster needles in black n blue for my 2000 Tahoe..any suggestions?? Ty.
junk yard.
@@TahoeSteve HEY TY SO MUCH..LOL..ODK HOW WELL THAT WILL WORK OUT BUT, IT'S WORTH A SHOT
you have for silverado 99 and what is the cost?
I don't sell them, check out US Speedo
Wjat year is your because the position of my bulbs on the back of my gauge cluster is different and I have a 05 Z71
So i have the same gauge set up as you but i can only find the stainless face that has a trans temp gauge. What is the exact part number you got?
All i can do is send you directly to the source to make sure you get what you need: www.usspeedo.com/
After doing this. it looks great, however my internal turn signal indicators and cruise indicator no longer light up, even though the cruise control does work and the external turn signals flash. Been trying to run down a fuse but can't find one that's blown. Ugh so close
The bulb(s) for the warning indicators are probably burned out. If you decide to replace them, I would suggest to replace all of them. There are two different sizes . . .
* Warning Indicators - Qty. 4
- Halogen Bulb - 74 or 2721
- LED Bulb - T5
- 3/8" Socket
* Needle Gauge's - Qty. 6
- Halogen Bulb - 194, 195, 168
- LED Bulb - T5 or T10
- T10 sockets
Hope this helps!
Will this fit a 2000 Chevy Silverado?
Can i just change the bulbs to blue
sure
Johnny Riley same
Where did you get from
where can i find a guage face for my car an 07 ford focus se 2.0lt engine?
check www.usspeedo.com
What tools did you use to take out all 4 screws? I have a small one i can take out the top 2 but the bottom 2 i can't do anything to because theres no room.
Medrano_ 59 use an extension
JT King can't find the proper size i know its 9/32 but can't find the extended one im at home depot rn
Medrano_ 59 if you don't have it yet look for a 1/4 extension. Or whatever size rachet you're using. Home depot should have them. If not either Sears, Lowe's, or Ace should have them as well
Medrano_ 59 autozone should have them as well
Why the gloves and does this cluster have the adhesive on the back of it?
gloves protect from getting smudges on the stainless steel and yes
That was an amazing video I'll definitely have to do this to my duramax
Thanks so much for watching
How did you change the mileage and gears to blue from Green
I didn't, that's just how it ended up.
Is this same gauge face still available?
should be. check out www.usspeedo.com/
I'm on the website but can't find them. I have an 04 tahoe. so I need the ones you bought. please help.
04 was a new generation, correct? if so - it might not be available.
My Tahoe was a PPV (Police Pursuit Vehicle) before I bought it. It says Certified under the MPH and it goes up to 140 m.p.h. I've only picked it up a lil over 130 MPH. Tahoe is a beast anyway, it's been hard to find one for mine. Can Anyone help me finding one or a place that can make me a custom one. If not maybe I'll go with one of this but i wanna keep searching before I give up. Thanks and I will highly appreciate it 👍
thanks for watching!
So I installed this on my 02 avalanche but when I turn my truck on, the fuel and oil needles go way below the zero mark and won’t go up. Neither will the RPM and MPH needles
Did you follow the directions EXACTLY when you installed it?
@@TahoeSteve Just went back right now to reinstall the needles step by step. Fixed it now, thank you
Cool video
thanks
Excellent video! I'd like to add a little bit of flare to my boring dash. Where may I find this Dash kit? If you don't mine me asking..
1524mclovin google
What does the red battery mean mine has it every time to lol
means your battery voltage is down.
Steve's 5 C's what do i gotta do? Change the battery?
only if your battery is giving you issues. you can check your battery voltage with a multi-meter. if your battery is acting fine, then you need to check the alternator. To check your alternator, first, open the hood and start the car. While the
engine is running, remove the negative cable from the battery. If the vehicle stalls or dies, the alternator is likely bad
Steve's 5 C's yeah guess its the alternator but thanks ! Life saver subbed for sure.
great to hear, glad to help!
Fake I click on the link to buy the same one we site pops up and says restricted no account
Yo can you build me one of does?
buy it
How do you calibrate the needles?
items ships with template that you mark before removing and just put them right back where they were according to your template
My Dash Is lights is going out how can I change them
this is how i did mine ua-cam.com/video/Cf2b6nZvEsU/v-deo.html
Fuckn tight!
thanks for watching!
How much do u charge for this