So, it is a 2-channel (stereo) amplifier with 4 parallel outputs. (channels of amplification). The problems I have with the circuit are the following: No fuse on secondary or primary transformer side. No chassis ground connection. No proper stretch relief on the mains cable. No protection against chafing from the chassis metal on the mains cable. The lack of fusing is the most serious problem.
Nice video, but this not a surround sound amplifier, the 5.1 decoder is missing, also using the 5 v supply from the same transformer output will give a beeping sound for the BT.
its a 4 multi chanel stereo Amplifier, for 5.1, you need a circuit that makes a 5.1 division at stereo signal, or a digital processor that have 5 +1 outputs
do you know what (5.1) surround system is ? you have made amp but it will work as stereo. 1). you haven't install any any any low frequency filter for sub. 2). you have no option to give 5.1 signals as input, Bluetooth (USB , micro sd card, FM) only only support stereo (2.0)
It's not surround 8.1 but it's mono 8.1 (4ch stereo inside = 8 ch mono, and 1sub ch outside). If u want a 5.1 surround, u need: Front L, Front R, Surround L, Surround R, Center and 1 SUB
I suggest you introduce some protections: general fuse on the alternating network, fuse on each amplifier. antibump circuit and protection for direct current in speaker output. variable gain buffer on each audio input. check the diode bridge if it has a high peak current ... with nearly 40,000 microfarads of smoothing, you can't imagine the initial charge current… it's scary. optimizes charging with a slow charging circuit. the two voltage regulators do not have to work like this, they need two 0.1 microfarad capacitors connected in input and output and an inverted diode between output and input. . between heatsink and power chip, it is better to use thermal paste. the convective motion of the air is wrong on the heat sink. regards.
This is a stereo setup but with more output, you wont get surrounding effect like 5.1 or dolby, you will get experience like normal amp or headphones, if you use any 5.1 or 7.1 decorder then you can get the real effects
Long ago I made 4 channel surround sound with one 4440 plate n two 6283 plates it was good as heat sink was big n two transformers of 4 amp each 12 0 12 ...
just making 5 1 port surround sound amplifier, not processor. good for using latest computer audio output which is deliver 5.1 audio process, input from gaming motherboard or mini surround sound capable audio decoder. good idea, cost effective. But need to more watts for Sub Woofer out.
Vidio accha hai,ager music n chala kr maukhik roop se btaya gya hota to chat chand lag jate End me sound quality check krani thi Aur sub boofer ke liye kya arrenge kiya,use bhi ed kiya jana tha,sab complet kr sound quality check jrur krani thi
precisamente eso mismo me preguntaba? en aliexpress venden decodificadores para 5.1 y 7.1. podrian haberse esforzado y colocarle uno y si pensaban hacer un amplificador multicanal pudieron haberle conectado un control de tonos
De acuerdo,8 canales o no pero El decoder lo compras tu, LOL,demostro que es barato y eficiente ensamblando ,donale otra pinza o stripper,talvez corrija El titulo y ya no se quejen.
Only for bass tube amplifier chahiye ghar ke liye. Mere pas 2 basstube hain but uske amplifier full dead ho gaye hain. Uske liye kaisa amplifier board chahiye aur ghar me kaise chala sakte hain? Please explain in details.......
এইটা পিউর ৫,১ সিস্টেম হয় নাই। সাব ওফার লো পাস ফিল্টার সারকিট নাই। এটা থেকে স্টোরি ও সাউণ্ড পাওয়া যাবে। ৫,১ সারাউন্ড সাউন্ড পেতে হলে অডিও ডিকোডার লাগাইতে হবে।
দাদা আমি একটা এম্লিলিপার বানিয়ে ছি ওটাই সাউন্ড সিস্টেম বাড়াতে হবে ও ব্যেস বাড়াতে হবে কি কি পাস পাল্টাতে হবে যদি আপনি একটু প্লিজ বলেন তবে ভালো হয় । 9134901253 এটা আমার ওয়াসব নাম্বার
Make it with 4 bord or 4 different bords....and put a passive crossover which are inbuild....one bord for sub, one bord for Mid, one bord for Woofer, one ford for tweeter, And do bord design same size and different types like 30w, 50w,100w,150w,200w etc and then do the magic ... Change the perticular bord if need more power or just simply pick bords of customers choice like 100w sub and 200w mid and 50w tweeter....at same power supply Power supply 12v 4amp...and put power enhancer with protection in each bord or customer change power supply if he/she need 2 bord or 3 bord as per as required.
Bom dia meu amigo da ELectronics Help Care ! Queria saber de vc. Onde vc conseguiu estas plaquinhas amplificada. Teria como me passar o site onde se vende elas. Com este TDA7297 devem ser poderosoas?
what you make is a amp with 2 ch input and 2 x 4ch output not an 8 ch amplifier. And also that is not surround Amp because you dont use sound processor, for 5.1 at least you must use sound processor like Dolby Digital system or better
if you use independent signal input for each amplifier you can make suround system, but you will need suround input signal. For 5.1 you can use 1x 2.1 amp, 1x stereo amp and 1x mono amp ( center channel).
Laga sakte ho lekin generally 10% se kam ripple voltage ke liye capacitor ki value decide ki jaati hai. 12 volt ke output ke liye minimum 2000 MFD capacitance per ampere load use kiya jata hai. 10,000mfd ka ek capacitor bahut sahi value hai music system ke liye.
Sir I have a doubt that i have a resistor but i do no its value pls tell me the value its colour code is (red, black, black, black, brown) pls sir tell me the value
For the circuit diagram please visit here
shorturl.at/FNS56
So, it is a 2-channel (stereo) amplifier with 4 parallel outputs. (channels of amplification). The problems I have with the circuit are the following: No fuse on secondary or primary transformer side. No chassis ground connection. No proper stretch relief on the mains cable. No protection against chafing from the chassis metal on the mains cable. The lack of fusing is the most serious problem.
Yes. This guy is a dumb. He only makes easy power supply circuit and connects with pre-made different circuits 😂
Not 5.1 ?
0 Tt
@@minhdang108 no is not
I could be or he might be right hoping they are operating at different frequencies
Nice video, but this not a surround sound amplifier, the 5.1 decoder is missing, also using the 5 v supply from the same transformer output will give a beeping sound for the BT.
Yes
Ya
Yes
V good bahut accha amplifier banaya hai wiring bhi acchi ki hai
its a 4 multi chanel stereo Amplifier, for 5.1, you need a circuit that makes a 5.1 division at stereo signal, or a digital processor that have 5 +1 outputs
Can u help me in getting a best quality circuit pcb board
@@sekhardakuaskd µPC1892 - Matrix Surround Sound Processor With Sound Processor
इसका आवाज भी सुनाइए।एतना बड़ा वीडियो बनाया सो पीस के लिए।
This guy is genius!! Wish I had the knowledge he has.. 👍👍
Un ora della solita musichetta senza una parola! Pazzesco!
do you know what (5.1) surround system is ?
you have made amp but it will work as stereo.
1). you haven't install any any any low frequency filter for sub.
2). you have no option to give 5.1 signals as input, Bluetooth (USB , micro sd card, FM) only only support stereo (2.0)
All you need to add 5.1 prelogic board and 4558 subwoofer circuit board to make it 5.1 amplifier .
This is only a 4 channel speaker system..
Nice video dada love form Kolkata.
I think it is not surround amplifier,, but amplifier 4 chanel
Only 2 chanel
Is not 4 its 8 channels no way
Stupid it's 4 amps with a channels.... Go harvest and shut up
Agree
yes it's not 5.1 sorund but 4chanel power ... I just agreed
It's not surround 8.1 but it's mono 8.1 (4ch stereo inside = 8 ch mono, and 1sub ch outside). If u want a 5.1 surround, u need: Front L, Front R, Surround L, Surround R, Center and 1 SUB
Good job with all the best information
Good work bro💖💖💖💖💖💖💖💝💝💖💝💝💝💝💝 sri lanka 🇱🇰
I suggest you introduce some protections: general fuse on the alternating network, fuse on each amplifier. antibump circuit and protection for direct current in speaker output. variable gain buffer on each audio input. check the diode bridge if it has a high peak current ...
with nearly 40,000 microfarads of smoothing, you can't imagine the initial charge current… it's scary. optimizes charging with a slow charging circuit. the two voltage regulators do not have to work like this, they need two 0.1 microfarad capacitors connected in input and output and an inverted diode between output and input. .
between heatsink and power chip, it is better to use thermal paste. the convective motion of the air is wrong on the heat sink. regards.
yes i agree with u
Good information
Proper biasing is also required
Magnifico trabajo, felicidades y gracias por compartirlo.
Tda7297 its max 15 + 15 w with 10% thd, and max power dissipation 33 w not 60w
Yes it is the ic used in tv for N 10 watts speaker 😂😂
পুরা ভিডিও দেখতে অনেক সময় গেলো রে ভাউ
I prepared this how much costs and when you deliver
Yours video amazing 😍
Thank you so much 😁
Whatsapp= +8801980060190
electronicshelpcare.net/how-to-calculate-wire-gauge-for-transformer/
....???
I TINK NOT WORK 5.1 AND I'M WATCING YOUR VIDEO ONE HOUR ....????
Fantastic work super explanation keep it up
Nice Project👏👏👏
This is a stereo setup but with more output, you wont get surrounding effect like 5.1 or dolby, you will get experience like normal amp or headphones, if you use any 5.1 or 7.1 decorder then you can get the real effects
woh perfect 2ch video hai 👍
Instead of playing background music you might have explain/ describe about each components other details
Wowwww amazing
Great video
I like
Long ago I made 4 channel surround sound with one 4440 plate n two 6283 plates it was good as heat sink was big n two transformers of 4 amp each 12 0 12 ...
just making 5 1 port surround sound amplifier, not processor. good for using latest computer audio output which is deliver 5.1 audio process, input from gaming motherboard or mini surround sound capable audio decoder. good idea, cost effective. But need to more watts for Sub Woofer out.
I need an amplifier 5.1 can u tells us cost ..and I want to talk to u..
Very instructive thanks for your video.
Very nice DIY amplifier! Congratulations! Dean Simic, an Electronics Engineer
Let me know the cost and 7.2 model or M500 which place in TN
you are doing a great work. I will follow your project.
Vidio accha hai,ager music n chala kr maukhik roop se btaya gya hota to chat chand lag jate
End me sound quality check krani thi
Aur sub boofer ke liye kya arrenge kiya,use bhi ed kiya jana tha,sab complet kr sound quality check jrur krani thi
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Thank you so much for giving us this kind of knowledge 👍👍👍
Excellent work sir
trafo 20A dioda 6A ?
Is is stereo system is it possible to make 5.1 output decoder for amplifier
Wire you purchase this chooser
30+ 30 amplifier mein kitne inch ke speaker chal sakte hain
What are you making bro..
Why did you short all input audio..??
How much piece
what's the blast radius tho
Hi sir transformer 12 0 12 h kya 5 amp ya ...
eso no es un amplificador 5.1 solo son varios amplificadores en paralelo. menuda perdida de tiempo. donde esta el decodificador 5,1?
precisamente eso mismo me preguntaba? en aliexpress venden decodificadores para 5.1 y 7.1. podrian haberse esforzado y colocarle uno y si pensaban hacer un amplificador multicanal pudieron haberle conectado un control de tonos
De acuerdo,8 canales o no pero El decoder lo compras tu, LOL,demostro que es barato y eficiente ensamblando ,donale otra pinza o stripper,talvez corrija El titulo y ya no se quejen.
Only for bass tube amplifier chahiye ghar ke liye. Mere pas 2 basstube hain but uske amplifier full dead ho gaye hain. Uske liye kaisa amplifier board chahiye aur ghar me kaise chala sakte hain?
Please explain in details.......
Bro what music you use at the first.
How get line out in stk 4141
Enth raite varum
Kitna whatt ka woofer lage ga
I think you have lots of fun
Super work 5.1 amp excellent
It's not a 5.1 it's 2x4ampli
Thanks and i agree with you
Bro did you put rubber gasket between IC and heat sink?
yea its better to use the rubber protection
can we play 4440 boad in ups 12 volt transformer...but its heavy amp...in transformer...so can we us it...plz reply
Nice work!..but get a fuse to each single Amp vcc and powersuply.. Just to safe your work ...;)
Bhai poora set kitne ka pdega agr mgana hai to kese mgay
சூப்பர் வீடியோ ❤️👍🙏
How to fix ON & OFF sound in 2.1 amplifier ?
Lol
Explain your problem sir
Send me where to buy the kit
Kiya karrahahey Sara audio grid 2 input mey jorrahahey via....comsecom opem drivde use kar...vai....4558ic sey
এইটা পিউর ৫,১ সিস্টেম হয় নাই। সাব ওফার লো পাস ফিল্টার সারকিট নাই।
এটা থেকে স্টোরি ও সাউণ্ড পাওয়া যাবে।
৫,১ সারাউন্ড সাউন্ড পেতে হলে অডিও ডিকোডার লাগাইতে হবে।
Hmm
ai jono sound test kore nai
দাদা আমি একটা এম্লিলিপার বানিয়ে ছি ওটাই সাউন্ড সিস্টেম বাড়াতে হবে ও ব্যেস বাড়াতে হবে কি কি পাস পাল্টাতে হবে যদি আপনি একটু প্লিজ বলেন তবে ভালো হয় । 9134901253 এটা আমার ওয়াসব নাম্বার
Vai 2 ta 15" voice coil 4" er speaker jonno koto watt er amplifier lagbe ektu bolte parben please?
Bom vídeo...Parabéns...
Could you tell me the name of the music group? Thank you
Ye sab saman kha se milega...?
It’s an Multi stereo Amplifier not 5.1 and it’s not 20A transformer. But good job 👍
Excelente trabajo maestro felicitaciones,hágame el favor de enviarme el diagrama,saludos cordiales desde Colombia.
Can we use a 12v 20amp SMPS instead of the transformer.
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Bhai saund to sunao
Kapistaer ke sath aap ne Jo black chij legai hai uska name kya hai
Ciao elettronics volevo chiederti cosa è quella pasta bianca che usi
What is the name of the back sound?
What is number of diode bridge use your power supply
can One Bluetooth module run 4 amplifier board without humming
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Para iniciar un proyecto está bien, la música de fondo es deprimente.
Make it with 4 bord or 4 different bords....and put a passive crossover which are inbuild....one bord for sub, one bord for Mid, one bord for Woofer, one ford for tweeter,
And do bord design same size and different types like 30w, 50w,100w,150w,200w etc and then do the magic ... Change the perticular bord if need more power or just simply pick bords of customers choice like 100w sub and 200w mid and 50w tweeter....at same power supply
Power supply 12v 4amp...and put power enhancer with protection in each bord or customer change power supply if he/she need 2 bord or 3 bord as per as required.
this video has no end
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Good job ❤️❤️
Haloo nice to meet you
Kalau mau beli pesan dimana ya ?
Bom dia meu amigo da ELectronics Help Care ! Queria saber de vc. Onde vc conseguiu estas plaquinhas amplificada. Teria como me passar o site onde se vende elas. Com este TDA7297 devem ser poderosoas?
How much cost it's coming and can you supply for me one piece
No sound , how good will it be if you could give out with the sound which you've assembled.
Gained a subscription by this video
Super అన్నయ
এতগুলা আউটপুট কোন কাজে লাগবে তারচেয়ে 4 ট্রানজিস্টর দিয়ে বানালে ভালো হবে
what you make is a amp with 2 ch input and 2 x 4ch output not an 8 ch amplifier. And also that is not surround Amp because you dont use sound processor, for 5.1 at least you must use sound processor like Dolby Digital system or better
if you use independent signal input for each amplifier you can make suround system, but you will need suround input signal. For 5.1 you can use 1x 2.1 amp, 1x stereo amp and 1x mono amp ( center channel).
power supply mai 4 capacitors ki jagah 6 capacitors lga diye jayen to kya voltage same rahegi...?
yes bro.full dc
Capacitor does not change Voltage, it only smoothening supply ripples.
Yes
Same rahaka
Laga sakte ho lekin generally 10% se kam ripple voltage ke liye capacitor ki value decide ki jaati hai. 12 volt ke output ke liye minimum 2000 MFD capacitance per ampere load use kiya jata hai. 10,000mfd ka ek capacitor bahut sahi value hai music system ke liye.
Kiya Kiya memorial lagega
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
ভাই এই মেশিন দিয়ে কত ইঞ্চি স্পিকার চালানো যাবে আর এই মেশিনে বানাতে কত টাকা খরচ হবে
Sir stk 4141 me se line out kese nikale please make a video
Sir I have a doubt that i have a resistor but i do no its value pls tell me the value its colour code is (red, black, black, black, brown) pls sir tell me the value
Transformer 20amp ? ? ?
Sound sunaye please
Is it 5.1 or 51 surround?
Parfact working 👍🏽
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Why y use 8 filter capasitor in the rectifier circuit
Sar muje microfon lage aesi baas tarbal bt banani he is me knse rajistar konse prat large