Great video! You make it look easy. I'm in the middle of replacing my ALH due to a spun rod bearing. I'm going to refresh my injectors and this video was perfect. BTW, where'd you get that t-shirt? It's bad-ass.
Thanks As for the tshirt I had it made I did a small run of them a little while ago. I have been considering doing an other run if there’s enough interest
Hello, very good and educative video! 👍 do stock injectors need balancing or setting up? Is this replacement plug and play? Are they just fine with stock tune? Or stage one? Thanks, looking forward on changing the nozzles from 0.216 from my 2.5 tdi ael , they are pretty much the same injectors, but 5 instead of 4
@@ERAutomotive thanks so much. Car was hardly running so I stayed up and changed tips. Freaked out afterwards thinking I screwed myself. Appreciate your time and information.
its all carbon deposits inside of the holes. No need to worry if some of it falls into the cylinder. chunks of carbon fly into cylinder anyway cause of the egr.
what about checking set pressure spry formation etc after installation??
All those mods you doing I did to my car already it is awesome or should I say they are awesome models including the Kerma Tdi tuning box
Great video! You make it look easy. I'm in the middle of replacing my ALH due to a spun rod bearing. I'm going to refresh my injectors and this video was perfect. BTW, where'd you get that t-shirt? It's bad-ass.
Thanks
As for the tshirt I had it made
I did a small run of them a little while ago. I have been considering doing an other run if there’s enough interest
@@ERAutomotive Put me down for two.
I would buy a couple shirts
Hi, please tell whixh way do you put the washers?
What's your reason for that intake considering the stock airbox is used on the VR6?
Customers car
great video, thanks for doing it! --did you notice much of a change in throttle response and acceleration with the new nozzles?
Yes definitely notice improvements in power
The tune really helps dial it all in
How did you get the stuck crush washer out of the chamber? I have one that wont come out by lifting it with a pick and its not sealing right either.
I used a long flat heat screw driver that just doesn’t fit inside the washer hole and
Gave it a push with my hand to wedge it in and lifted it out
Hi can i put nozzles fromael 2.5 tdi 103kw to ALH
I believe they are different
Not sure
Look up nozzles for both and cross the numbers and see if they match
Hello, very good and educative video! 👍 do stock injectors need balancing or setting up? Is this replacement plug and play? Are they just fine with stock tune? Or stage one? Thanks, looking forward on changing the nozzles from 0.216 from my 2.5 tdi ael , they are pretty much the same injectors, but 5 instead of 4
Injectors should be checked and balanced afterwards
Ideally tune to properly accommodate for the new nozzles
@@ERAutomotive Is the balancing done via ECU/VAGCOM or is it mechanical?
Mechanical
How do you crank the engine without starting it
It won’t start until it’s bled
So it's running on the stock tune?
That's good to know
Yes started and ran on stock tune
Then had a tune flashed on ecu a couple days later
@@ERAutomotive will it run around for a bit till able to get turned?
Yes
@@ERAutomotive thanks so much. Car was hardly running so I stayed up and changed tips. Freaked out afterwards thinking I screwed myself. Appreciate your time and information.
I have a fault code for cylinder 3 would replacing the nozzles fix my loss of power issue
Would have to do diagnosis to find the actual issue
how did you clean the injector holes without getting stuff in cylinder?
Clean the area as best u can b4 removing injectors and blow and vacuum area before and after removal is what I did
I took the risk
@@ERAutomotive yeah, pretty risky😅
I’m more then fine with it personally
its all carbon deposits inside of the holes. No need to worry if some of it falls into the cylinder. chunks of carbon fly into cylinder anyway cause of the egr.
Does injector 3 use a different tip or the same. Power line to it, not sure how that works?
Same tip
The wire is for needle lift sensor
@@ERAutomotive great thank you
How many nm do you normally lock the nozzle cap?
www.myturbodiesel.com/d2/1000q/multi/nozzle-install-TDI.htm
Specs are listed here
The t-shirt, nice job.
The car's still running?
Thanks I had a bunch made a while ago
Yes cars running great! No issues and great fuel mileage
1:29 video starts