great job put in these small components together, I have the same bored but I'm having problems with the radio the receiver is binding but the radio is not working. any help on this I appreciate it.
i hope you can help me... i solder for my fpv setup an adapter to the board but when i plug it in, it worked but after a second the transmitter and the f3 board goes off...
Salut Juste avoir une précision pour un branchement Flysky i6 récepteur 8A ver2. 0 . 4 fils rouge /noir : oka : +/- uart 2 Jaune ??? Blanc ?? Marci de votre aide... 😁😁
Hi my friend my. transmitters flysky fsi6, PPM is getting throtle and yaw commands when I connect but there is no movement on the pitch and roll side, what is the problem of working aux?
will this receiver " Flysky FS-A8S FS A8S 2.4G 8CH Mini Receiver with PPM i-BUS SBUS Output" work for this FC or the eachine tiny 32bit brushed FC. And if it does it should work with the turnigy evolution tx?
Hi, my V2.0 F3 EVO Brush Flight Controller will not come on. the red light lights up when usb plugged in. when i plug battery in, the round black copper coil thing gets hot but no lights come on. please help.
Being honest I do not have any Devo transmitters. What you can do is to ask online stores selling Devo 7E or get to the nearest RC shop. My SBUS receiver is as well radiolink receiver and it is compatible only with radiolink radios AT10 and AT9.
I have SBUS. If you have the same fight controller then DSM2 should be soldered to the top left soldering points. It is in the video (DSM or DSM2 is soldered to the same soldering points).
You should pay attention to the receiver type, Devo7 is 2.4Ghz radio as the most of other radios. My radiolink is 2.4Ghz radio but it can be linked with the different types or receivers: PPM, SBUS, PWM.
i cant get mine running on 2s as soon i plug the battery motors start spinning full speed i did solder the pin for 2s when i plug the 1s battery works fine
I was having this issue with 1S batteries. I tried something and it seems to have worked: If you motors start full power when plugging in your battery you have to set motor_pwm_rate to 16000. Go to your CLI and type: type: set motor_pwm_rate = 16000 hit enter type: save hit enter The issue I have now is my quad doesn't have enough power to take off. (even though I know it has)
thanks for taking your time out to make videos..great job learned alot
The best of all tutorial!all on details part by part!great work..sub u bro
Just the info I was looking for - thank you for the great info share.
you have to hook the fpv camera up to the lipo. The UARTS wont give you a constant 5v.
Great video to have. Added to my favorites.
Can we connect PWM reciever to it ? Like Flysky FS-A6 ?
great job put in these small components together, I have the same bored but I'm having problems with the radio the receiver is binding but the radio is not working. any help on this I appreciate it.
Nice informative video!! keep it up!
Can i use fsr6b reciever in this fc ??
nice video
if the camera has 4 wires. 5v. gnd. video in video out. alloy in uart rx and tx?
Is it possible for adding led?
Is it possible to connect battery and USB at the same time on this boar
if the jumper is on in 2s and using battery 1s is there a problem? it looks like my 1s jumper is defective
Where should I soilder for fpv camera
Olá muito bom sua explicação. Seu video muito bem explicado resolveu meus problemas.
Hi. Good video. a question, you know how to do the flash otherwise connect the card to the pc but it leaves USB NOT RECOGNIZED ..Thanks
Can a GPS module be added?
i hope you can help me... i solder for my fpv setup an adapter to the board but when i plug it in, it worked but after a second the transmitter and the f3 board goes off...
Salut
Juste avoir une précision pour un branchement Flysky i6 récepteur 8A ver2. 0 .
4 fils rouge /noir : oka : +/- uart 2
Jaune ???
Blanc ??
Marci de votre aide... 😁😁
Hi, this contoller is compatible with INAV Firmware? Tks
Where to squis ei ppm and ibus?
Hi my friend my. transmitters flysky fsi6, PPM is getting throtle and yaw commands when I connect but there is no movement on the pitch and roll side, what is the problem of working aux?
will this receiver " Flysky FS-A8S FS A8S 2.4G 8CH Mini Receiver with PPM i-BUS SBUS Output" work for this FC or the eachine tiny 32bit brushed FC. And if it does it should work with the turnigy evolution tx?
doubledigitdreams no
TheFastly WTF? Why not?
Did you solve it??
You will have to check the protocol of the receiver... If its "AFHDS A2" it will work with your turnigy evolution tx!
Thank you.
Please , type your Receiver ?
Hi, my V2.0 F3 EVO Brush Flight Controller will not come on.
the red light lights up when usb plugged in.
when i plug battery in, the round black copper coil thing gets hot but no lights come on.
please help.
Where to connect pwm receiver?
thanks dude for replying back i want to ask that can devo 7e be linked with DSM receiver pls reply back
coz i am using devo 7e
Being honest I do not have any Devo transmitters. What you can do is to ask online stores selling Devo 7E or get to the nearest RC shop. My SBUS receiver is as well radiolink receiver and it is compatible only with radiolink radios AT10 and AT9.
how did u get it to work im using radiolink as well but i cant get it going or even armed it
seu video me ajudou muito obrigado!!!
What is this TX2 pin for?
what is UART 1 for?
dude another question-which receiver you are using dsm or ppm or sbus coz i am using dsm2
I have SBUS. If you have the same fight controller then DSM2 should be soldered to the top left soldering points. It is in the video (DSM or DSM2 is soldered to the same soldering points).
whats the protocol for this FC?
which type of radio is devo 7e is it DSM or SBUS pls reply back i am stuck
You should pay attention to the receiver type, Devo7 is 2.4Ghz radio as the most of other radios. My radiolink is 2.4Ghz radio but it can be linked with the different types or receivers: PPM, SBUS, PWM.
Martin Puot dose this board have osd for rssi ?
Where to solder flysky a8s?
Transmiiter link pls
i cant get mine running on 2s as soon i plug the battery motors start spinning full speed i did solder the pin for 2s when i plug the 1s battery works fine
I was having this issue with 1S batteries. I tried something and it seems to have worked:
If you motors start full power when plugging in your battery you have to set motor_pwm_rate to 16000.
Go to your CLI and type:
type: set motor_pwm_rate = 16000
hit enter
type: save
hit enter
The issue I have now is my quad doesn't have enough power to take off. (even though I know it has)
thanks i will give this a try
it sill those the same thing :(
watch part number 4 it maybe about setting motor pwm rate. What board do you use? Is it from coretexrc?
micro naze32 brush i forgot the manufacture
Dose this have OSD ?
usefull
Dose this board support rssi and osd ?
Hello, do you know if the DSM2 receiver will plug into the DSM ports? I have a Dasmikro receiver I am trying to set up.
Thanks