SELKIRK SUPERVENT Chimney Flu through the wall kit install pt2 Drill Hole
Вставка
- Опубліковано 1 лис 2013
- SELKIRK Supervent chimney flue build pt2. Drilling through the wall to install a wood stove. DIY howto build SELKIRK Supervent chimney flue from basement wood / coal, pellet stove. Masonry drill bits and tips on drilling a hole in concrete wall large enough to install insulated double wall chimney pipe to vent wood stove / potbelly coal stove or pellet stove. www.rockntv1.com/2013/10/thru... Home Heating appliance, how to build video. Selkirk supervent stainless steel chimney flue installation from basement for wood, coal, pellet stove how to drill a hole in concrete. Install wood stove, diy build Selkirk Supervent chimney kit.
- Навчання та стиль
This guy’s accent is awesome! “2 and three carta!” 👍🏻👍🏻
thanks for watching
the through hole came out great on both sides of the wall, the long side of the 30 degree triangle nears 11" on 12" bit, easy to let up pressure, sds bit are grinders not cutters, yes vid on way to explain.
Nice educational video....it did help me a lot...thank you !!!
welcome
Pretty close to the vinyl siding, maybe install aluminum flashing about 12 inches wide with a right angle lip say 2 inches wide and about 2 feet long that will cover the siding to protect from heat. Heat rules and that could be a sensitive area. Great job.
Vinny
It is looking good. I did that 5 years ago but i used the same pipe but it was galvinised on the outside saved a lot of money on the total install.If anyone else is attempting this look in to it instead of the stainless steel pipe.
I thought I was the only one still using the old skill 1/2 drive drills. Workhorses I use for going through posts, concrete, and soil. I have a couple...probably outlast my Makita intended for this.
milwaukee
i would love a stone faced chimney but for now i take shiny stainless steel, thnx 4 watch n.
Hire a diamond core drill next time you''ll get a MUCH smoother hole, quicker , and with much less grief and less chance of straining your hands/wrists!! I have all sizes up to 152mm. My 220/150mm s/s flue is outside the house so, no walls to drill through!!
Diy for me, no hiring i bought the sds hammer drill ua-cam.com/video/2oWCiNP5ivM/v-deo.html
I'm doing this exact install. About to cut the hole. Did you drill a 9" hole for some extra room? Just curious since yours looks pretty good.
yes
Why did you use the 30 degree elbow it looks like you would still had room to clean out and get a brush under the T with a straight joint ?
tht t is straight ,, you clean top down
Question for you....Selkirk's installation instructions specifically say not to offset the T-Joint to go around a soffit. I notice you did and I am thinking of doing the same (24"). Yours has been installed now for over a year, have you had any problems having done that?
no i did'nt, its a straight shot up past the shingles
Also if you have a drill without a clutch pump the trigger to stop it pulling your wrist out.
is youtube deleting my comments? thanks for watching
you are putting a sds+ drillbit in a normal drilling machine ?
what I do is use a thin drillbit, 8mm in the middle and when it reaches the inside I make a cord on it with a pencil, draw the same circle on the inside and drill arround the edge with a small drillbit, that prevents the explosion in the inside (most of the times).
but your hole (in the wall) looks great, just perfect
no, video about the bit .. > ua-cam.com/video/XHdQfIB-A0A/v-deo.html and the new drill ---> ua-cam.com/video/2oWCiNP5ivM/v-deo.html
what was the make of the stainless vent pipe looks nice?
.Selkirk super vent
What is 3 cottas?
3x .25
0.250... a cotta
three cotta inch drill bit. recodded real time.
and you edited that comment??
2 And 3 cotter inches? ha ha right on
thanks for watching
Drill tru da concrete
drill through the wall yes?
@@ROCKNTV1 Yes sir! 👍
all righty then, i'LL bring my tools,, LOL ;-)
Get a Hilti hammer drill you won't have to worry about it twisting your arm off.
i did ua-cam.com/video/2oWCiNP5ivM/v-deo.html
Why do you need such a big device to vent the furnace?
wood / coal stove flue pipe
building code
Couldn't you have just used an electric stud finder instead of peeling the siding ?
I wanted dead center of the wall stud, finders will find misses. Vynle siding is easy to unzip.
Boston accent?
nope
Dude, where the hell are you from??
my neck of the woods north of Boston
ROCKNTV1 I’m in Portsmouth, NH. An hr north of Boston. I’ve never heard that accent before
born nyc
2 and 3 carter
Thats a measurement, I strive to be accurate, ;-)
Sorry bro it's not your measurements it is the way you pronounce quarter. Lol just poking fun
no worries,, its colokyal,, lol
You don't even have the "hammer" engaged on the drill
here ua-cam.com/video/2oWCiNP5ivM/v-deo.html hammer drill
Hello, How can i contact you via email or a website? Thank you!
For what?
At 4:05...I don't know this word?! "Orientated"...???
Is that from some foreign language that means "Oriented" (which means to align or position something relative to a specified position).
yes
He is sooooooooooooo aggressive!
born to play defence
a hammer drill would work better!!!! work smarter than harder
ua-cam.com/video/2oWCiNP5ivM/v-deo.html sds hammer drill