AEM Water Methanol Injection Kit | Full Installation Guide

Поділитися
Вставка
  • Опубліковано 5 лис 2024

КОМЕНТАРІ • 34

  • @GeovaniGarcia-pg7si
    @GeovaniGarcia-pg7si 8 місяців тому +1

    Amazing video! I have been watching a lot of installation videos and your is probably the best one I watched. Thanks for the walk down

    • @hyde_official
      @hyde_official  8 місяців тому

      Glad to hear your feedback. thank you.

  • @ALTF26
    @ALTF26 Рік тому +3

    Hey brother, I've watched many of your videos. Just want to say that I love your videos. Keep up the great content!

    • @hyde_official
      @hyde_official  Рік тому +1

      Thanks, bro. I appreciate it and thank you for the support.

  • @dr.gintoki8206
    @dr.gintoki8206 10 місяців тому +1

    Thanks for the tutorial. I’m watching this one before installing the same kit on my turbo jeep wrangler jk.

  • @VideoClubstar
    @VideoClubstar 11 місяців тому +1

    Super awesome install video 🎉

    • @hyde_official
      @hyde_official  11 місяців тому

      Glad you liked it! More to come! There is a little easter egg on how I "manage" safe mode when the the WMI fails. I'll be a short. so stay tuned.

  • @brentsowell7144
    @brentsowell7144 21 день тому +1

    Need to see how you installed the filter. Having a hard time

    • @hyde_official
      @hyde_official  20 днів тому

      I ended up not using the filter anymore. It was on the way and didn't like the way it looked on the engine bay. it was tacky.
      if you really want to want. Just get any inline filter that uses a quick push and lock disconent.
      In all, I revised my line, which I am now happy using the AN6 line instead without the filter.
      you certainly can get away with it if you want as it's optional.

  • @illwil1005
    @illwil1005 9 місяців тому +1

    Outstanding job bro!!!

  • @elitecol69
    @elitecol69 3 місяці тому +1

    solenoid is meant top go to ignition supply not to permanent power from the battery directly.

    • @hyde_official
      @hyde_official  3 місяці тому

      correct, and that is how it is connected. In fact, in this setup, the WMI controller sends power to the solenoid. there is no direct permanent power to the solenoid. It is activated by the WMI controller.

  • @sabz_bhp
    @sabz_bhp 3 місяці тому +1

    Hi bro great video. You know the pump u bolted it to the plate. How did u then bolt it to the boot floor?

    • @hyde_official
      @hyde_official  3 місяці тому

      bolt is at the same place where the negative cable of the battery bolts to the chassis. Unscrew the bolt. Put the plate and the battery terminal and bold it. details are in the video.

  • @myrx2
    @myrx2 8 місяців тому

    Unless the car is retuned for water meth it wont make more power. In some cases it might lose power. Also water meth isn't what makes more power. It gives the tuner options to add more boots or adjust the timing.

    • @hyde_official
      @hyde_official  8 місяців тому +2

      just like using e85. if your car is not tuned for e85, you gain no power. After you've set up the kit, the ECU must be tuned to make an account of the additional fueling. This topic isn't part of this video. this video is for installation only. There was no proper video that could have detailed the installation as I did. Either way, your statement is correct.

  • @TheBeastgp
    @TheBeastgp Рік тому +1

    The kit comes with a non return valve at the injector. That’s why it doesn’t come with a solenoid.

    • @hyde_official
      @hyde_official  Рік тому +1

      it is still advised. if you can, please do so.

  • @jeremybrea1910
    @jeremybrea1910 2 місяці тому

    What’s the green cable connects to?

    • @hyde_official
      @hyde_official  2 місяці тому

      the green cable is used for fail safe. some EUCs can use that to trigger on the fly map change in the event of meth system failure. if I had b48 or B58 this would have been a great way to utilize it since the platform supports multimap.

    • @jeremybrea1910
      @jeremybrea1910 2 місяці тому

      @@hyde_official so you need to connect that one to the ecu?

    • @hyde_official
      @hyde_official  2 місяці тому +1

      an ecu that is capable of reading this signal. my car does not have this capability, so I didn't use it

  • @hollywood2177
    @hollywood2177 2 місяці тому

    Methanol doesn’t add power it’s a safety net for when you do add more power or boost to keep temps low. Also helps clean ++ nice vid! This with e85 you might just be able to call it a freezer 🥶

    • @hyde_official
      @hyde_official  2 місяці тому +1

      Negative. that is the main purpose of this video to debunk the myth of those who don't know about this system. If you don't tune your car for WM, you end up losing power. Do you know why that is? that's your homework to find out if this video doesn't convince you.

    • @KillJD
      @KillJD Місяць тому

      Umm you are wrong lol. Water/meth cools intake and cylinder temps and increases your effective octane rating. It creates a denser air charge and suppresses knock. This you can run more boost and timing for a given setup.

  • @oldfashionedwrx3574
    @oldfashionedwrx3574 4 місяці тому

    What metal size for bracket

    • @hyde_official
      @hyde_official  4 місяці тому

      could you please provide more information about what bracket you're referring to or the timestamp in the video?

    • @oldfashionedwrx3574
      @oldfashionedwrx3574 4 місяці тому

      @@hyde_official 6:20 ish

    • @hyde_official
      @hyde_official  3 місяці тому

      this should work, too amzn.to/4eZSxfd

  • @iamalittlefarmer
    @iamalittlefarmer 7 місяців тому +1

    In Canada it is a criminal chargeable offense to do this., to bad

    • @hyde_official
      @hyde_official  7 місяців тому +1

      you must always follow the law. Most racing applications don't have this restriction.

    • @KillJD
      @KillJD Місяць тому

      I'm in Canada and I don't give a fuck lol