Hey, Have you figured out your problem yet. I just installed a Shelly Plus 1 on the same CO-Z gate motor. We have the same control board, but my manual has a slightly different DIP switch set up. That worked for me. Try turning OFF only switch 1 (DOWN) and leaving 2 & 3 ON (UP). That did the trick for me. before, all I could do was close the gate when open as the common and close pins were used, so that is the only way the gate will run, however with DIP switch 1 (ONLY) in the DOWN position. it works just like the control fob. open, Stop, Close etc. Hope it helps with your situation.
You may not have configured your magnet right..... also the wifi thing comes with a magent-selonoid sensor that you need to place at the right place. It could be just that.
Do you know which terminal I should use to power my Wi-Fi gate opener… you vid help out a lot this whole time my dip switch were on smh. Right work fine fine but I heard you can get power directly from gate control board to power on Wi-Fi gate opener came with 2 wire red and black.
About the switches. You only need the first one to be down the other 2 are for your gate go close automatically after a certain time. I just installed my motor and I have noticed the same problem where some times It doesn’t open or close. It does it just like yours only moves like half an inch. But mine does it with the original remote controller. I checked my magnets with a multimeter to make sure that they are in the right position and they are. Did you found out what causes your gate to not close after opening all the way?
Unfortunately I still have that problem with it not closing when open all the way. But the alarm status and notifications fixed it self and I have real time notifications. I really haven't had time to look into it, but when I do I'll post something. Thanks
Well shortly after that video one of my dogs chewed up the exposed wires and I kind of gave up. It's been a while so maybe I'll try again. Lol. On a side note the gate opener has not failed me once 🔥. It's a workhorse, that thing opens at least 6 to 10 times daily. Sorry I don't have an answer for you.
Hey, Have you figured out your problem yet. I just installed a Shelly Plus 1 on the same CO-Z gate motor. We have the same control board, but my manual has a slightly different DIP switch set up.
That worked for me.
Try turning OFF only switch 1 (DOWN) and leaving 2 & 3 ON (UP).
That did the trick for me.
before, all I could do was close the gate when open as the common and close pins were used, so that is the only way the gate will run, however with DIP switch 1 (ONLY) in the DOWN position. it works just like the control fob. open, Stop, Close etc.
Hope it helps with your situation.
You may not have configured your magnet right..... also the wifi thing comes with a magent-selonoid sensor that you need to place at the right place. It could be just that.
The reason why your garage is getting stuck it's because the sensor is pushed too much to the back try play with it so you don't have that issue.
I think you have to grease the flux capacitor the muffler bearing and change the fuse on the thermal coupler you should be OK after that.
You could be right, lmao
Pinché enano 🤣🤣
No problem…Thanks
Do you know which terminal I should use to power my Wi-Fi gate opener… you vid help out a lot this whole time my dip switch were on smh. Right work fine fine but I heard you can get power directly from gate control board to power on Wi-Fi gate opener came with 2 wire red and black.
I'd have to look into that. Thanks
About the switches. You only need the first one to be down the other 2 are for your gate go close automatically after a certain time. I just installed my motor and I have noticed the same problem where some times It doesn’t open or close. It does it just like yours only moves like half an inch. But mine does it with the original remote controller. I checked my magnets with a multimeter to make sure that they are in the right position and they are. Did you found out what causes your gate to not close after opening all the way?
Unfortunately I still have that problem with it not closing when open all the way. But the alarm status and notifications fixed it self and I have real time notifications. I really haven't had time to look into it, but when I do I'll post something. Thanks
Which appt can I use for the CO-Z gate opener?
Did you ever find the answer to ur problem because I can’t get mine to work with the Wi-Fi module that it came with
Where did you get your gate painted? I want my old gate painted that color but not sure where or what color is it called? Thanks!
It's actually a powder coated Bronze. It was done before it was installed. Thanks
@@elfocker oh looks nice thanks for the info
First u need a repeater close by n seconds u need connect limit switch normally close to work right
Have wifi repeater close by so can get better signal
Do you do house calls?
🤣
Did you ever figure the problem out when is was opened and you went to close it
Well shortly after that video one of my dogs chewed up the exposed wires and I kind of gave up. It's been a while so maybe I'll try again. Lol. On a side note the gate opener has not failed me once 🔥. It's a workhorse, that thing opens at least 6 to 10 times daily. Sorry I don't have an answer for you.
The chains are twisted