Common Voltages are 120 (110/115), 208 (200), 230 (220/240), 460 (440/480), 575 (600), VAC (volts of alter- nating current) with a frequency of 50 or 60 Hz. Welding power source transformers are designed to work with these voltages. Most welding power sources are made to operate on more than one primary voltage value.
So what is the spark plug for? Why do you need a 30,000V insulator for something that operates on 24V? Why not just connect the wire straight to the welding rod? In fact, instead of wrecking two expensive batteries, why not buy a $50 stick welder?
My respects and praise to the op for this post You have handled the critics very well and politely congratulations Thank you for your post ive have heard of diy direct current welders being made and used successfully in the bush to get things repaired enough to get out of trouble and home safely To the critics here join the farkew
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
"Fantastic video! The demonstration of using spark plugs and a 12V battery for welding was incredibly detailed and easy to follow. I learned a lot about improvising welding techniques with simple tools. Thank you for sharing such valuable knowledge!"
Wonderful video. Using UA-cam I have managed to create an extensive collection of really useful tools.. My work as a part time brain surgeon would be impossible without the vast range of my new equipment.
Thank you for viewing and leaving a comment. If you don't understand, don't hesitate to write to me in the comments section of the video so I can help you
Ну возможно он обмазку пробил винтом когда закручивал ручку . Но я как то сомневаюсь в том что 4ку электрод варит от двух аккумов по 6в . Про технику безопасности с работой дуговой сварки он тоже не слышал
Ну наконец-то! Хоть один стоящий комент и на родном языке. А то все буржуйский и буржуйский...И все как один собираются свечи ломать. Кстати впервые вижу как дохлые акб работают в режиме КЗ. Буржуйская дешевая порнуха...Да ик чему здесь свечи?! Лохотрон...по буржуйски.
Amazing video! The welding technique is genius, and the way you break everything down makes it easy to understand. I’ll definitely give this a try. Can’t wait to see more from your channel!
Thank you for viewing and leaving a comment! Wishing you success and luck in life. If you are unclear, don't hesitate to write to me. I'm ready to support you
@@Tips365day Thank you for your interest in my comment. I hope you can come up with good and practical tips for the audience to apply. Wish you more and more success
@@TrendDIY Friends, I am talking about experience and the times I have tried This job only creates small sparks and can only weld very thin pieces of iron
تي الك عيوني سيف سوالي هل حاليا عمله التون الخاصه بالهامستر حاليا موجودة كعمله رسميه في منصات التداول يعني اكو عمله تون هامستر ويكدر مثلا شخص انو يحول عمله تون هامستر الى عمله اخرى لو لا لحد الان مامطروقه بمنصات التداول
It's not a fake, it's possible, but it doesn't make sense, because for the same price as the destroyed materials, you can buy an electric one that can be used for a very long time
با این دو باتری مدام نمیشه جوشکاری کرد اما به عنوان ایده برای مواقع اضطراری که دسترسی نیست و جوشکاری لازم هست بسیار کار گشا و عالی هست 👍👍👍@@Tips365day
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
24 Volts is low for stick welding . Not at all, it depends on the filler rod being used. Stick welding is done with a “constant current” power supply which means that the current output will be constant, but the voltage can float depending on the arc length
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
He would get better and more powerful results if he had kept the diesel engine from where the spak plug came. The bigger that diesel engine, the better the ground will be Specially if someone turn the drive shaft slowly. Then one by one the 16 spark plugs will ignite weld with plenty of time to cool off. Good work you did´ i´m impress. May be use of propane or butane gaz to avoid oxygen contamination would help your weld.
Dude , how many batteries you are going to damage before you finish a gate for a fence for example. Isn't better to to home Depot and buy a welder machine. Oh sorry maybe you don't have a Home Depot where you are from , but I'm pretty sure Amazon will deliver a cheap welder that it is going to work for you much better
He spot welded, with a few seconds cool down between each arc. Had he run a continuous bead he wouldn't have gotten very far before the batteries melted down! A cheap welder would be far superior and less costly than two new batteries.
Một ý tưởng đáng để học hỏi. Tận dụng đồ cũ tưởng chừng như bỏ đi, nhưng với những nhà sáng tạo nó lại là công cụ tuyệt vời. Cảm ơn bận đã chia sẻ video.
Thank you for watching the video and leaving your feedback. If you don't understand, don't hesitate to write to me below the video's comment section so I can assist you
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
They say when you jump start a car it is the battery with the most juice which is most reactive and therefore a case of standing clear just in case the internal plates warp leading to an internal short.
فعلاً. انا مش فاهم كثير في الكهرباء خصوصاً فكرة اللحام، ولكن توصيل السالب بالموجب لبطاريه ومدبله هذا يسبب انفجار وحريق والا ؟ غير عن ذلك، ليش بالاساس يستخدم انبوب الخزف اذا ريشة اللحام متصله مع المسمار ثم الى المقبض والسلك؟
The necessity of the spark plug escapes me. It's nothing more than window dressing. You could have done the same thing with any clamp arrangement! Wakodahatchee Chris
yeah i do not get what the point is of using that ceramic part of the plug like some kind of isolation, also i don't get how he established conductivity through the rod with the flux on it since he did not hook his wire to the back where the exposed metal tip is ,,all he does is give the same bs copy n paste reply to everyone and does not answer questions
Exactly what I was thinking from the beginning when the video referred to using 12-volt batteries: What is the purpose of the spark plug? And that is still my question!
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
how were you able to establish electric conductivity through the rod with the flux on it? because you did not hook your wire to the back exposed tip of the metal rod ,,and please give me an answer and not just repeat the same "thank you for watching etc" like you do for all the other replies
I believe the cable from the batteries was connected to the set screw, tapped into the spark plug base, that also clamped to the welding electrode. The problem with the whole setup, as I see it, is that if you tried to run a continuous bead, even for a couple of seconds, the voltage would decay rapidly, and you couldn't maintain the arc. That is why he spot welded with a cool down between each arc. Even using this spot-welding technique, the batteries would likely turn to garbage before very long.
@@rossk4864 yeah the batteries will def die fast but he simply fed the electrode through the ceramic holder then tightened a screw which i doubt broke through the flux on the rod to establish conductivity so i'm still puzzled
@@rossk4864 exactly and as i said i do not think the screw on the side of his gun holding the rod is breaking through the hard flux coating on the rod unless im wrong but that would be the only contact he can possibly have
У нас колхозники в поле так использовали. Аккумуляторы чтобы что-то заварить ещё семьдесят лет назад,потому что Сагов не было. А причём здесь свечи вообще не понял ....
Спасибо, что посмотрели видео и оставили комментарий! Если вы не понимаете, не стесняйтесь, напишите мне в комментариях к видео, чтобы я мог вам помочь.
Можно 50 или 52 метра провод купить. Толщина конечно от 0,8 до 1 см примерно. Замотать в виде эллипса.В ютюбе или на просторах интернета подробнее все описано. Конечно не профессиональный аппарат с силовыми транзисторами. Конструкция старая, но варить можно. Это когда нет денег человек выкручивается. А за 20 тыс. Рублей можно профессиональный аппарат купить.
Все заметили какой у него инструмент? На раскопках нарыл что-ли?. Как прокручивал провода к АКБ, показал. А как начал варить, не показал к какому сварочному аппарату подключил их. Лохотронщик.
@@zen_makerЛюди! Не говоріть на акумулятори АКБ. Бо розшифруйте всі три букви? Просто "Акумулятор". Або, як у книжках для радіоаматорів писалося просто "Б" або "Бат" - батарея. Якщо треба наголосити, що це саме акумуляторна батарея - тоді "АБ", без всякої букви "К".
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
I predict about two to four inches of bead and the batteries would need to be recharged or replaced. Batteries do not like to be shorted in this manner. I am also pretty certain that when the batteries are shorted, the voltage and current would collapse and you would not get enough heat for good weld penetration.
Thank you for watching the video and leaving a comment! If you don't understand, don't hesitate to write to me in the comments of the video so I can assist you
பொதுவாக கார்பன் ஆர்க் வெல்டிங் இம் முறையில் செய்யமுடியும். Intermittent dc.யில் தான் arc welding செய்ய முடியும். இறுதி காட்சி வெல்டிங் செய்யும் போது இணைப்பு முழுவதும் காட்டப்படவில்லை எனவே இந்த படக்காட்சி fake.திறமையான வேலைகள் மூலம் ஏமாற்ற முடியும்.
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
Que palhaçada 😮 Primeiro: Faz dos outros estúpidos... E alguns são realmente porque acreditam em tudo! Segundo: Compra-se máquinas de soldar fabricadas para o efeito, mais baratas que 2 baterias ! Esta treta de vídeos deveriam ser punidos... Não deixa de ser uma burla. Tentam ganhar algo à custa da estupidez de outros.
Also ich nehme statt der Zündkerze nur noch einen Isolan-Porzellator. Zur Reserve habe ich mir mit einem Trennschleifer mehrere von einem Freileitungsmast (20 kV) abgeschnitten. Kann ich empfehlen, wundervolles Feuerwerk 🎆🎇
The quality of your videos is outstanding, always making me learn something new!
Thank you so much
Е55е5ё🎉🎉🎉🎉🎉@@Tips365day
❤❤❤❤❤❤
گ@@Tips365dayضضضضضض۱۱12😮
Common Voltages are 120 (110/115), 208 (200), 230 (220/240), 460 (440/480), 575 (600), VAC (volts of alter- nating current) with a frequency of 50 or 60 Hz. Welding power source transformers are designed to work with these voltages. Most welding power sources are made to operate on more than one primary voltage value.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
How long does the soldering time with these batteries last??????? One hour, two hours more????? And is it charged? Can you clarify?
@@Tips365day
Creo que el voltaje no es tan importante como el amperaje
So what is the spark plug for? Why do you need a 30,000V insulator for something that operates on 24V? Why not just connect the wire straight to the welding rod? In fact, instead of wrecking two expensive batteries, why not buy a $50 stick welder?
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Sinung naka try na nito dito sa phillipines
Becaause he,s stupid
My respects and praise to the op for this post
You have handled the critics very well and politely congratulations
Thank you for your post ive have heard of diy direct current welders being made and used successfully in the bush to get things repaired enough to get out of trouble and home safely
To the critics here join the farkew
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
Папа Карло умер давно... А Буратино с дубом вместо мозга продолжаю рождаться😢😢😢
"Fantastic video! The demonstration of using spark plugs and a 12V battery for welding was incredibly detailed and easy to follow. I learned a lot about improvising welding techniques with simple tools. Thank you for sharing such valuable knowledge!"
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
😂😂😂😂
Они один хрен не поймут твоего Русского юмора😂😂😂можешь не стараться
@@Alexs_RPD_ Я тоже охренел с этой свечёй, 24 волька и пасатижами можно варить!...
Wonderful video. Using UA-cam I have managed to create an extensive collection of really useful tools.. My work as a part time brain surgeon would be impossible without the vast range of my new equipment.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
😂😂😂
Stick with surgery, this is not new equipment, get a welding machine instead!
It is very valuable to make new designs like this... I am from Sri Lanka🇱🇰🇱🇰🇱🇰
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
@@Tips365day 👍👍👍
Welche neuen Designs, du Spinner? Habt ihr hier nicht mehr alle Latten am Zaun?
Your idea of welding from 12v x2 = 24v battery with spark plug is really creative, I will definitely learn from you, thanks for sharing
Thank you for viewing and leaving a comment. If you don't understand, don't hesitate to write to me in the comments section of the video so I can help you
خیلی جالب بوداستادولی نمیدونم چرا نمیتونم باورکنم فکرمیکنم که غیرممکنه😮
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Нобелиевскую премию чуваку! Единственный в мире чел, который смог добиться прохождения тока через обмазку электрода.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Ну возможно он обмазку пробил винтом когда закручивал ручку . Но я как то сомневаюсь в том что 4ку электрод варит от двух аккумов по 6в . Про технику безопасности с работой дуговой сварки он тоже не слышал
This is suicidal device as battery can explode with current required for welding. Just like short circuit.
@@manager7532смотрел внимательно? Аккумуляторы оба по 12в ,последовательно 24в😂
Ну наконец-то! Хоть один стоящий комент и на родном языке. А то все буржуйский и буржуйский...И все как один собираются свечи ломать. Кстати впервые вижу как дохлые акб работают в режиме КЗ. Буржуйская дешевая порнуха...Да ик чему здесь свечи?! Лохотрон...по буржуйски.
Amazing video! The welding technique is genius, and the way you break everything down makes it easy to understand. I’ll definitely give this a try. Can’t wait to see more from your channel!
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Dude, according to my experience, it is impossible to solder with a 25.5V source.
Dude, you shouldn't fool the audience like that
Thank you for viewing and leaving a comment! Wishing you success and luck in life
Thank you for viewing and leaving a comment! Wishing you success and luck in life. If you are unclear, don't hesitate to write to me. I'm ready to support you
@@Tips365day Thank you for your interest in my comment.
I hope you can come up with good and practical tips for the audience to apply. Wish you more and more success
According to you, 24v current cannot be welded, have you tried it?
@@TrendDIY
Friends, I am talking about experience and the times I have tried
This job only creates small sparks and can only weld very thin pieces of iron
تي الك عيوني سيف سوالي هل حاليا عمله التون الخاصه بالهامستر حاليا موجودة كعمله رسميه في منصات التداول يعني اكو عمله تون هامستر ويكدر مثلا شخص انو يحول عمله تون هامستر الى عمله اخرى لو لا لحد الان مامطروقه بمنصات التداول
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
totally fake! in the end real welding machine is used
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Z betul broo palsu soalnya saya tukang las sejak 1996 sampai sekarang jdi tau klw itu setingan
It's true.Only 24V,36v, 48v. Ok
You can try 36V,48v.The best 🎉🎉🎉
It's not a fake, it's possible, but it doesn't make sense, because for the same price as the destroyed materials, you can buy an electric one that can be used for a very long time
در اخر از دستگاه جوش واقعی استفاده شد.. در اخر باطری ها رو نشون نداد.
This is not for security anyone with a magnet can open it
😂 есть гораздо тупее😢! Дело было вечером, делать было нечего!😮😅
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Una idea geniale bravissimo ❤una domanda una batteria che ha più vott è uguale lo stesso grazie
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
видео о том как угробить 2 акамулятора😁
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
با این دو باتری مدام نمیشه جوشکاری کرد اما به عنوان ایده برای مواقع اضطراری که دسترسی نیست و جوشکاری لازم هست بسیار کار گشا و عالی هست 👍👍👍@@Tips365day
Если пальцы уцелеют в процессе.😅
Your idea is wonderful. I don't think you can come up with those ideas. worth learning. 💞
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Жаль потраченного времени на просмотр
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Я пожалуй досмотрю хотя уже понял что ерунда
Зато поняли что автор видео полнейший даун😂
Да уж. Буржуи еще те.
Good Job 👍
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
24 Volts is low for stick welding . Not at all, it depends on the filler rod being used. Stick welding is done with a “constant current” power supply which means that the current output will be constant, but the voltage can float depending on the arc length
valójában a gyujtási fesz.-hez
45 V kell......
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
А каким боком эдесь свечу примазали? Чтобы понты создавать?! Гниль...
Ingenious!!!!!! So smart!
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
BuDiscarded spark plugs can still be used in welding machines, very good and useful tips
Thank you for viewing and leaving a comment! Wishing you better channel development
next time try to use coconut leave bone as electrode. its work well as mosquitos repelant
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
afterthat the butteries can never be used anymore.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Don't ever trust this video.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
2@@Tips365day
انا من مكه
nó lừa đảo
Nie oglądać naciagacza
Wow amazing ideas 🎉🎉🎉
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
I was a professional welder for thirty years and this is a crock of.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
This question is for the real welders. What would be the pros and cons of this? Does this actually work? Please respond.
Thank you
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
@@Tips365day Thank you may God bless you as well.
The positive connection buffles me, the welding rod must be clamped on the tip not on the body,
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
面白い！
溶接機を買った方が早いけれど無駄な時間をかけるのが最高の贅沢。😊
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Está ótimo. Agora mostra a máquina de solda escondida! Esse arco de solda não é dessas pequenas baterias. Nem todos são tolos!
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
На сколько электродов хватит этого заряда?!😢
It is real and works.. All you need is some rods, jumper cables and car battery
He would get better and more powerful results if he had kept the diesel engine from where the spak plug came. The bigger that diesel engine, the better the ground will be
Specially if someone turn the drive shaft slowly. Then one by one the 16 spark plugs will ignite weld with plenty of time to cool off. Good work you did´ i´m impress. May be use of propane or butane gaz to avoid oxygen contamination would help your weld.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
I don't think anybody who can weld or work on diesels read your comment yet!!!
@@maxwebster7572we never know, even with my silly comment😊
Battery will be discharged within minutes
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Finally You are just showing the welding by hiding the entire circuit,
so, not everyone are fools.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Dude , how many batteries you are going to damage before you finish a gate for a fence for example. Isn't better to to home Depot and buy a welder machine. Oh sorry maybe you don't have a Home Depot where you are from , but I'm pretty sure Amazon will deliver a cheap welder that it is going to work for you much better
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
He spot welded, with a few seconds cool down between each arc. Had he run a continuous bead he wouldn't have gotten very far before the batteries melted down! A cheap welder would be far superior and less costly than two new batteries.
He visto que está de moda arruinar baterías en UA-cam. EL SPONSOR es chino o alemán?
Это так,что-то тоненькое приварить точечной сваркой.На сколько хватит аккумулятора?
Откуда вы беретесь такие )
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
I didn't expect that there were so many types of tools, each with its own function.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
I like this idea.its smart.❤
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Ok terimakasih berbagi ilmunya,, ini sangat menginspirasi saya,
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Một ý tưởng đáng để học hỏi. Tận dụng đồ cũ tưởng chừng như bỏ đi, nhưng với những nhà sáng tạo nó lại là công cụ tuyệt vời. Cảm ơn bận đã chia sẻ video.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Ang galing
Great tip dear friend.The video presents an excellent welding technique using spark plugs and a 12V battery.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
К чему здесь свеча зажигания?! Один идиот собирает вокруг себя таких же...
really amazing, unbelievable but true 👍🏻, thank you so much!
Thank you for watching the video and leaving your feedback. If you don't understand, don't hesitate to write to me below the video's comment section so I can assist you
in last your are in set one rod .you have to show it is plain or welding rod
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Wow amazing are those welds strong?? Let’s say to weld a motor cycle frame or a gocart frame???
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
Güzel yapmışsiniz alternatif olarak güzel olmuş emeğine yüreğine sağlık kardeşim
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Você é fera
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Зря смотрел, теперь не могу спать.😂
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Свечей подкинуть? Иль буржуйская халявная сварка из дохлых АКБ спать не дает?!
Covered electrode Dia. 2.6mm need 60A and 21V at least to keep stable arc(V) and melt(A) tip of electrode and base metal
They say when you jump start a car it is the battery with the most juice which is most reactive and therefore a case of standing clear just in case the internal plates warp leading to an internal short.
Hatur nuhun telah berbagi pengalaman ilmu nya
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
✅Padu Bossku
❤Sukaaaaaa
👍
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
يحاولون دائما الخداع من اجل كسب المشاهدات والاموال
والله صدقت هدا معقول ماهو معقول البطاريه ماتتحمل تنفجر هدا يبقى له 50 امبير و 220 فولت لدلك حط
Unlike فيديو فاشل والابلاغ عنه شكرا
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
@@Tips365dayA Internet deveria bloquear esse tipo de vídeo de enganação. Só serve para vizualições, nada mais do que isso. 👎👎👎👎👎👎👎
فعلاً. انا مش فاهم كثير في الكهرباء خصوصاً فكرة اللحام، ولكن توصيل السالب بالموجب لبطاريه ومدبله هذا يسبب انفجار وحريق والا ؟
غير عن ذلك، ليش بالاساس يستخدم انبوب الخزف اذا ريشة اللحام متصله مع المسمار ثم الى المقبض والسلك؟
🇹🇷🇹🇷Türkiyeden Selamlar....Videolarınız bilgilendirici Teenkü
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Hello, your content is very good and useful, thank you👍👍👍
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Я тоже хочу попробовать эту идею спасибо тебе друг
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
D'accord, tu moi as donné une nouvelle technique attrayante ! Merci beaucoup de t'excelente création attrayante
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
The necessity of the spark plug escapes me. It's nothing more than window dressing. You could have done the same thing with any clamp arrangement!
Wakodahatchee Chris
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Cerdas
yeah i do not get what the point is of using that ceramic part of the plug like some kind of isolation, also i don't get how he established conductivity through the rod with the flux on it since he did not hook his wire to the back where the exposed metal tip is ,,all he does is give the same bs copy n paste reply to everyone and does not answer questions
Exactly what I was thinking from the beginning when the video referred to using 12-volt batteries: What is the purpose of the spark plug? And that is still my question!
It’s just a Asian big booger welding video !👎👎👎
SUPER INVENTION .MERCI
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
Very nice weldan 🎉🎉🎉🇳🇪👍
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Good time, teacher, your works are really beautiful 💖🤌👍🌹 and unique 💖💖
A craftsman who loves his job with effective sharing
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Потом аккумуляторы выбросит в мусор)
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Тупее видео поискать надо.
Samsun havzadan izliyorum kolay gelsin dileyiyle
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Sayın hemşehrim bu arkadaş gereksiz bir uğraş yapmış.yapilan işe de tabi ki saygımız vardır.bu fevkalade durumlar için değerlendirilir
how were you able to establish electric conductivity through the rod with the flux on it? because you did not hook your wire to the back exposed tip of the metal rod ,,and please give me an answer and not just repeat the same "thank you for watching etc" like you do for all the other replies
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
I believe the cable from the batteries was connected to the set screw, tapped into the spark plug base, that also clamped to the welding electrode. The problem with the whole setup, as I see it, is that if you tried to run a continuous bead, even for a couple of seconds, the voltage would decay rapidly, and you couldn't maintain the arc. That is why he spot welded with a cool down between each arc. Even using this spot-welding technique, the batteries would likely turn to garbage before very long.
@@rossk4864 yeah the batteries will def die fast but he simply fed the electrode through the ceramic holder then tightened a screw which i doubt broke through the flux on the rod to establish conductivity so i'm still puzzled
@@ARCSTREAMS Actually, I did notice that and then forget that he wasn't clamping the bare end of the electrode. Good point.
@@rossk4864 exactly and as i said i do not think the screw on the side of his gun holding the rod is breaking through the hard flux coating on the rod unless im wrong but that would be the only contact he can possibly have
Wire connection by Nut&Bolt -not Twisting -Thanks for Experiments. .
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
У нас колхозники в поле так использовали. Аккумуляторы чтобы что-то заварить ещё семьдесят лет назад,потому что Сагов не было. А причём здесь свечи вообще не понял ....
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Thank you bro.. very good idea...
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
You didn't need to use a spark plug. Too Leeds would have done.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
What to do when the welding rod heats
Ich bin begeistert von diesem Mist! Wie kann man mit einem Trennschleifer so umgehen und die dilettantischen Kabel-Verknotungen😂😂😂😂
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
бред, просто провода к элетроду сложно подключить?
Спасибо, что посмотрели видео и оставили комментарий! Если вы не понимаете, не стесняйтесь, напишите мне в комментариях к видео, чтобы я мог вам помочь.
poser assistindo o video pensando em uma coisa do outro mundo, dsq simplis só encosta o fio no eletrodo
Muito bom
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Saya jadi pengamat aja.mendukung postinganmu
Gostei muito dá sua ideia vou tentar fazer isso ☺️
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
-А я хотел сварочник купить за 20 000р. Как хорошо что я вовремя это посмотрел. Может и от батарейки сварить получится?
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Натуральный колхоз.
Можно 50 или 52 метра провод купить. Толщина конечно от 0,8 до 1 см примерно. Замотать в виде эллипса.В ютюбе или на просторах интернета подробнее все описано. Конечно не профессиональный аппарат с силовыми транзисторами. Конструкция старая, но варить можно. Это когда нет денег человек выкручивается. А за 20 тыс. Рублей можно профессиональный аппарат купить.
Ellerine sağlık kardeşim 🇹🇷🇹🇷
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
How about the chance that you make the batteries explode by doing so ?
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Tu es un génie mon frère.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Not safety at all ,why ppl do not use protection on cutter disks
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Lol...this is how it's done in the real world. Safety be damned...that's right.
Galing ah.
Все заметили какой у него инструмент? На раскопках нарыл что-ли?. Как прокручивал провода к АКБ, показал. А как начал варить, не показал к какому сварочному аппарату подключил их. Лохотронщик.
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
от двух автомобильных акб вполне можно варить , но конечно с обычным электрододержателем.
@@zen_makeril a utilisé le céramique de la bougie comme porte-électrode
@@zen_makerЛюди! Не говоріть на акумулятори АКБ. Бо розшифруйте всі три букви? Просто "Акумулятор". Або, як у книжках для радіоаматорів писалося просто "Б" або "Бат" - батарея. Якщо треба наголосити, що це саме акумуляторна батарея - тоді "АБ", без всякої букви "К".
@@СтудіяЛесь АКкумутятерна Бавторейка !
вполне лагишно ! имхо. 🤔
Excelente 👍 gracias por la enseñanza
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
No entiendo inglés, quise reenviar para pedir que alguien me lo traduja
Столько замарочки. 😊
Pinocho otra vez asoma la nariz
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
@@Tips365day , не вешай людям лапшу на бошки...Порожняк это все.
Good bro
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
Одним словом американец Задорнов про них в своё время всё сказал
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
@TipПод зад пдобных деятелей со всех каналов.s365day
Задорнов не був американцем - він був "русскім", тобто, ворогом України.
Excellent
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Sweet, good idea that. How long'd the batteries typically last I'm wondering? I'd make 1 of these myself, jus pick up a battery r 2 maybe,
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Не показал подробностей ,как в туалет ходил... зачем автомобильная свеча? Есть держаки проще
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
ОН ТиБЯ "ПОНИЛ", НО Я ПАТЗРИВАЮ ШТО ТЫ ЧОТА ПСДИЖ
в данном случае это пример процесса со свечой с ее керамикой
Listen to the Rooster!!!
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Totally fake video.last me edit video
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
How long will the two batteries last?
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
I predict about two to four inches of bead and the batteries would need to be recharged or replaced. Batteries do not like to be shorted in this manner. I am also pretty certain that when the batteries are shorted, the voltage and current would collapse and you would not get enough heat for good weld penetration.
Ý tưởng thì có , thực hiện theo kiểu này ko bao giờ khá lên nổi bạn ơi !
cảm ơn bạn đã xem video và để lại nhận xét! Nếu chưa hiểu đừng ngần ngại viết thư cho tôi ở dưới bình luận của video để tôi có thể hỗ trợ bạn
I especially like the chickens in the background
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Try use 6011 rod with three batteries in series and will do the job.
Thanks for watching and leaving a comment! If you don't understand, write to me in the comments so I can help you
Tuong tác nhé bạn mình cung ché tạo theo dam mê
Просто полный пипец! 😂😂
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Inventive 👍
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
GoodJob..veryVery Good ..Bravooò!!
Thank you for watching the video and leaving a comment! If you don't understand, don't hesitate to write to me in the comments of the video so I can assist you
பொதுவாக கார்பன் ஆர்க் வெல்டிங் இம் முறையில் செய்யமுடியும். Intermittent dc.யில் தான் arc welding செய்ய முடியும். இறுதி காட்சி வெல்டிங் செய்யும் போது இணைப்பு முழுவதும் காட்டப்படவில்லை எனவே இந்த படக்காட்சி fake.திறமையான வேலைகள் மூலம் ஏமாற்ற முடியும்.
Thank you for watching the video and leaving your feedback. Every comment you make helps the channel grow and motivates me to work more effectively. May God always bless you
@@Tips365day பொதுவாக யார் மனதையும் புண்படுத்துவது நோக்கமல்ல புதிய கண்டுபிடிப்புகள் சரியாகவும் பாதுகாப்பு மிக்கதாகவும் இருக்கும் போது வரவேற்கப்படும்.
Se usar um carregador de bateria com entrada de 220 v e saída para 12v, acho que também daria. Vou tentar.
Tenho um carregador possante parado aqui e o trafo tá bom.🤔👉estou c/ uma idéia 👉💥🙉☠️🔥💥💥💥🤪🏃💥Tomare q dê certo😐🙆😅
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively
Que palhaçada 😮
Primeiro: Faz dos outros estúpidos... E alguns são realmente porque acreditam em tudo!
Segundo: Compra-se máquinas de soldar fabricadas para o efeito, mais baratas que 2 baterias !
Esta treta de vídeos deveriam ser punidos... Não deixa de ser uma burla.
Tentam ganhar algo à custa da estupidez de outros.
Also ich nehme statt der Zündkerze nur noch einen Isolan-Porzellator. Zur Reserve habe ich mir mit einem Trennschleifer mehrere von einem Freileitungsmast (20 kV) abgeschnitten. Kann ich empfehlen, wundervolles Feuerwerk 🎆🎇
Thank you for watching the video and leaving your feedback. Each comment you make helps the channel grow and motivates me to work more effectively