Hi, I have a D5 with the old motherboard. I am considering buying the D5 EVO motherboard to upgrade the old motherboard. Is this doable, would you happen to know if I require any other extras before I commit myself to this purchase?
Thanks for the Video Hilton, my gate moves then stops. Then moves again and stops again. Suspect its the Dos sensor like you say. Tried reseting limits but then just moves quickly one direction then other and stops again. Doesnt move slowly to end stop and back. Ill have a go and clean the dos sensor tomorrow (Fingers crossed it will work) but thanks for the Video
Forgot to mention its a D3 older motor simular in your Video and did replace Battery with new one. Checked all fuses and relays latches fine. Initially thought that the Collision sensitivity is too low and tried changing to 3level where gate stops with difficulty but this also didn't help. After looking at your video I suspect the dos sensor so will open there where you said where you turn to release gate and clean dos sensor also.
Is there a way to test the Dos sensor ? Gate still doing the same. When programing limits it moves slightly stops then goes back slightly then stops again
I have checked and replaced all the fuses. I have changed the battery, the charger and now the main power supply, but it keeps giving the low battery warning and stops maybe a meter after opening and everything goes off. If I connect a separate charger on the battery and let it charge that way it opens fine until the battery is to low. The diagnostic screen shows the battery at 13V and the charger at 14V. What can be the problem?
@@johanleroux7140 Unfortunately not. Something very strange is going on. The electricians that came out can't find any problems. They said I should replace the entire unit, now my supply seems to be switching polarities every week
Morning Hilton. My Evo shows the remotes triggering the controller but does not trigger the motor to run. Already reseted to factory settings no change. Re added the remotes no change. Motor open and closes gate when using the test button. Help please. J
Hi,, My D5 Evo says Gate Drive Failure , what could be the problem a new battery was installed 4 months ago, checked all wires and fuses all ok,battery checked using multi meter
Check the green plug on the right hand side of pc board, 4 wires it mounts into a plug on the pc board they can come loose or fail, take pc board into centurion they can fix or give you a service exchange
Hi when you programmed your gate motor your neighbours may have been pressing their remotes and now they opening your gate , best to re-program your remotes
sounds like your disengage is stuck. Happened to me now. turn it to disengage as far as you can and use something to try and pry the gate open. should force it to disengage. should not take a lot of force as soon as the gate moves a bit turn the dial to engage again, pull on the gate a little then try to disengage it again
@@kabelolethale8663, reset the limits and put something on the track before the gate closes, like a hammer or heavy object about 1meter on the track, then if the gate stops there then you know its picking it up
@@aubreymatodlana924 check the doss sensor, my D5 motor has an older one that's a black box on the bottom right side under a green box, it was full of sand from ants once i cleared it and connected it my gate started working properly.
@@FuturePress1 Okay I see, so it is more of a software issue? Initially I was thinking it could be the computer itself... I will found out about it, thanks a lot 👍🏾
thanks Hilton, very helpful tips
Hi Hilton. Thank you for this video, my gate had magnet problem.
Good work, well done
Great stuff, it was the disc behind the engaging wheel. Just cleaned it and relearned.
Hi,
I have a D5 with the old motherboard. I am considering buying the D5 EVO motherboard to upgrade the old motherboard. Is this doable, would you happen to know if I require any other extras before I commit myself to this purchase?
Thanks for the Video Hilton, my gate moves then stops. Then moves again and stops again. Suspect its the Dos sensor like you say. Tried reseting limits but then just moves quickly one direction then other and stops again. Doesnt move slowly to end stop and back. Ill have a go and clean the dos sensor tomorrow (Fingers crossed it will work) but thanks for the Video
Forgot to mention its a D3 older motor simular in your Video and did replace Battery with new one. Checked all fuses and relays latches fine. Initially thought that the Collision sensitivity is too low and tried changing to 3level where gate stops with difficulty but this also didn't help. After looking at your video I suspect the dos sensor so will open there where you said where you turn to release gate and clean dos sensor also.
Is there a way to test the Dos sensor ? Gate still doing the same. When programing limits it moves slightly stops then goes back slightly then stops again
When I tried to engage motor the spine handle is off.what is going on, do you know
How do I fix it when I set the limits but the computer resets during the process? Thanks
My gate opens but won't close. Seems like I'm the only one with that problem
My gate keeps opening once ive just closed it?
I have checked and replaced all the fuses. I have changed the battery, the charger and now the main power supply, but it keeps giving the low battery warning and stops maybe a meter after opening and everything goes off. If I connect a separate charger on the battery and let it charge that way it opens fine until the battery is to low. The diagnostic screen shows the battery at 13V and the charger at 14V. What can be the problem?
Hello KG did you ever find the problem with your gate motor? My gate motor is doing the same thing
@@johanleroux7140 Unfortunately not. Something very strange is going on. The electricians that came out can't find any problems. They said I should replace the entire unit, now my supply seems to be switching polarities every week
My gate keeps multiple times when i try to open it please help with a possible diagnosis
Morning Hilton. My Evo shows the remotes triggering the controller but does not trigger the motor to run. Already reseted to factory settings no change. Re added the remotes no change. Motor open and closes gate when using the test button. Help please. J
Hi. If you find out the issue please tell me what it is
Hi, our gate motor opens by itself immediately after we close it. What could be the issue? Our battery still seems fine thou.
I had the same problem, I set the limits again of the gate and it worked great.
L1 is flashing twice and no status light help please
Hi,, My D5 Evo says Gate Drive Failure , what could be the problem a new battery was installed 4 months ago, checked all wires and fuses all ok,battery checked using multi meter
Check the green plug on the right hand side of pc board, 4 wires it mounts into a plug on the pc board they can come loose or fail, take pc board into centurion they can fix or give you a service exchange
Hi Hilton. Whst would be the reason the gate just randomly open?
Hi when you programmed your gate motor your neighbours may have been pressing their remotes and now they opening your gate , best to re-program your remotes
Re-program your remotes , your neighbours are opening your gate with their remotes
my motor wont engage to manual when i rotate the dial, please help and how do i fill the oil
sounds like your disengage is stuck. Happened to me now. turn it to disengage as far as you can and use something to try and pry the gate open. should force it to disengage. should not take a lot of force as soon as the gate moves a bit turn the dial to engage again, pull on the gate a little then try to disengage it again
O meu motor parou aí meio
Only when Load shedding ..Gate closes 100% and then opens ..after 1 or 2 times it closes ..The battery and in side 12-+ is 12.7 volts Why ????
I changed the battery & it still opes half way or quater way
Let it charge the battery
Hi Hilto,my remote just fleshes,it doesn't open or close my gate
Replace battery
Pls help...mine just makes a clicking sound
whats up me 078 528 7361
How to fix if sceeen switches off whilst the gate open
Replace battery
These gate motors have way to many issues. This is coming from a technician who works on them often.
Please help. I get error saying "Setup fail, no end stops found"...I do have end stops and it was working fine all along
Hi what motor is it , is your battery ok ?
@balugasailing Hi. It's the centurion D5. Yup the battery is good, changed it three months ago
@@kabelolethale8663, reset the limits and put something on the track before the gate closes, like a hammer or heavy object about 1meter on the track, then if the gate stops there then you know its picking it up
Hii sir need help
My gate is stops half way when opening and when I press remote again it closes slowly. What could be the problem?
Could be that your battery is finished
The battery is new , I bought it in October
@@aubreymatodlana924 check the doss sensor, my D5 motor has an older one that's a black box on the bottom right side under a green box, it was full of sand from ants once i cleared it and connected it my gate started working properly.
How do I remove the cover? It is stuck. Thanks.
Hi
Use the key to open then shake the cover left to right then lift it up.
That's the only way
@@thulanijohn620 Mine has a spring-loaded pin that I have to push in, in the back that locks the cover, I found out. Thanks.
@@phumeoli thanks
I'm happy all is good
My D5 will close and back out open with a gap.
Mine does the same thing, did you manage to find a solution for that issue??
@mduhyx2120 my intaller came back to update the software and set up the open and close limits.
@@FuturePress1 Okay I see, so it is more of a software issue? Initially I was thinking it could be the computer itself... I will found out about it, thanks a lot 👍🏾
Only when Load shedding ..Gate closes 100% and then opens ..after 1 or 2 times it closes ..The battery and in side 12-+ is 12.7 volts Why ????