Thank you very very very much, you just made my day… tried this and it worked, I have been burning calories opening my gate for almost a week until I came across your video 🤙🏾
Brilliant Jubert, baie dankie! My error was "Drive Fault" but I figured close enough. Disconnected the charger and power (which was only battery at the time, loadshedding 🙄). I unplugged the other thingy but this motor's only a few months old so just put it back in. Then plugged power & charger back in... et voila! I guess this amounts to a restart of the system. Reboot for older folk... or IPL for us real old-timers 😂
Ive come across this fault in the past. It's not common and the board displays a motor fault and not a doss fault as it should . Often it can also be a bad motor wire connection on the board. I had it show this out of box because the terminal connection was not tightened properly on assembly. Good tip to look out for . I always carry test boards, doss and inner motors to eliminate faults . These are fantastic motors and I swear vy them . I used them for near on 20 years amd been through all their models.
@@TheInfamousBlood It's does have a doss just not in the same place . Check you connections and the motor wire connection onto the PCB . If it's showing drive fault it may be that the wires are loose . I've also had it in occasion that the battery connecter on the board was not making good contact . It's hard to tell without checking onsite . Been in the industry over 20 years and still come across odd faults .b
Mine its written motor fault i called the same person who did the installation and he is charging me an arm an a leg😢😢i have eatched this video and tried follow your instructions im still not winning im not sure if maybe im not scratching the right part on the dos sensor the gatemotor is only 3 years old
Check the motor wire connections on your board . Sometimes it's a simple as it's not making proper contact. I've been in the industry 20 years plus and have come across this doss fault in the vid . Most times the motor can be repaired . I have sometimes had to replace the control card as the board is faulty but only once I've tested everything else . I always carry tests boards and doss kits to eliminate any other issues . Sometimes I'll fit a test part and have the client run their motor for a few days just to make sure it's sorted out then come back with a replacement part if needed . Good advice in the vid .
Pls my machine is just a month old and d control board went off and refused to on again. Initially, it on nd showed rest all power nd under it it writes"waiting for co-processor" I took another board to d machine nd d board is working with d machine Bt is showing me tor failure. Please how can I resolve it. Thakks
The old Centurion D5 gate motors were great, now they brought out this new crap, that gives me loads of trouble, from working perfectly on day and the next day not, I get an error "too many collisions"Now WTF does that mean and how do I fix it?
One year later and your video is still helping, thanks 🙌
Thank you very very very much, you just made my day… tried this and it worked, I have been burning calories opening my gate for almost a week until I came across your video 🤙🏾
You’re most welcome mate
Jubert ... you legend! Sorted out in 5 minutes flat. So appreciate your video.
Thank you, I cleaned the sensor and we are up and running again
How do I remove that NO OIL ALLOW
I find it difficult to remove the sensor chip from it place
Good Day. This is actually a tacho meter. It counts the revolutions of the gear.
Thanx so much helped with my motor, had no corrosion but just wiped it and put it back, seems fine for now, thanx God bless u
Wooow... this really worked 😅. Thank you soo soo much for your help🙏🙏.
Brilliant Jubert, baie dankie! My error was "Drive Fault" but I figured close enough.
Disconnected the charger and power (which was only battery at the time, loadshedding 🙄). I unplugged the other thingy but this motor's only a few months old so just put it back in. Then plugged power & charger back in... et voila!
I guess this amounts to a restart of the system. Reboot for older folk... or IPL for us real old-timers 😂
Good morning
You are a star ✨✨✨ thanks you !!!
Been struggling 1 hour then found your video. Working hundreds now 👌🏻👌🏻👌🏻 thank you
Tnx, been fighting for a week with it, did what you showed and it worked. 🙏🙏
Thank you worked like a charm, much appreciated
Ive come across this fault in the past. It's not common and the board displays a motor fault and not a doss fault as it should .
Often it can also be a bad motor wire connection on the board.
I had it show this out of box because the terminal connection was not tightened properly on assembly.
Good tip to look out for .
I always carry test boards, doss and inner motors to eliminate faults .
These are fantastic motors and I swear vy them . I used them for near on 20 years amd been through all their models.
Hi Colin I have a D10 motor giving me this issue but it doesn’t have the sensor like this D5. Any idea how I can access it?
@@TheInfamousBlood
It's does have a doss just not in the same place .
Check you connections and the motor wire connection onto the PCB . If it's showing drive fault it may be that the wires are loose .
I've also had it in occasion that the battery connecter on the board was not making good contact .
It's hard to tell without checking onsite .
Been in the industry over 20 years and still come across odd faults .b
This also worked for me, thank you for sharing.
Thankyou for your well explained video and for sharing your knowledge
You’re most welcome
thank you. I took your advice and it did what it should do. it worked.
Very helpful, thank you. My gate works
You solved my problem thank you wow 👏 👏 👏 👏 👏
Thanks you just helped with this video
It worked. Thank you👍🏽👍🏽👍🏽
You're welcome!🎉
So after unpowering the mainboard completely, it still remembers the open/close routine? I.e. you don't need to reprogram it?
Thank you that was really hepfull 🙏
Glad it was helpful!
What do I do with the wheel thing? I think that’s why my gate won’t work should I make the wheel tight or loose send help
And if you changed the dos sensor would it work ?
Thank you for sharing.
Thanks so much for this
Hi, my D5 evo throws a DOSS faulty. it does 5 beeps 10 times, any clue what that might be?
Please help. I get error saying "Setup fail, no end stops found"...I do have end stops and it was working fine all along
Any one know how to install a pillar light on d5 smart. Cant find any video on how to do it
I have a double gate, one closes but the other does not want to. Maybe I should check this.
What are possible causes of drive fault
What should i do if its saying IRB C FAILURE
I find it difficult to remove the chip from it place
Baie dankie
Jy is baie welkom Dries
Can someone tell me the name of this blue garget next to red capacitor
Origin Magnet Sensor
I want to know how to restart mother board centurion d5
Explain to irbc failure
I cleaned the chip contacts but the still persit and still cums with motor drive failure
Same here
Mine its written motor fault i called the same person who did the installation and he is charging me an arm an a leg😢😢i have eatched this video and tried follow your instructions im still not winning im not sure if maybe im not scratching the right part on the dos sensor the gatemotor is only 3 years old
Sounds like the sensor had too much corrosion and is beyond repair. Either that or the motor got physical damage.
@@jubertvos3126 that's too bad 😪😪😭😭😭
Check the motor wire connections on your board . Sometimes it's a simple as it's not making proper contact.
I've been in the industry 20 years plus and have come across this doss fault in the vid .
Most times the motor can be repaired .
I have sometimes had to replace the control card as the board is faulty but only once I've tested everything else .
I always carry tests boards and doss kits to eliminate any other issues .
Sometimes I'll fit a test part and have the client run their motor for a few days just to make sure it's sorted out then come back with a replacement part if needed .
Good advice in the vid .
@Colin Hudson thank you so much the issue has been resolved it was such a small problem nothing needed to be replaced. Again thank you.
Pls my machine is just a month old and d control board went off and refused to on again. Initially, it on nd showed rest all power nd under it it writes"waiting for co-processor"
I took another board to d machine nd d board is working with d machine Bt is showing me tor failure. Please how can I resolve it. Thakks
Drive fault \ status
The old Centurion D5 gate motors were great, now they brought out this new crap, that gives me loads of trouble, from working perfectly on day and the next day not, I get an error "too many collisions"Now WTF does that mean and how do I fix it?