How to Replace Crankshaft Position Sensor 2003-2008 Honda Pilot
Вставка
- Опубліковано 13 гру 2023
- Buy Now!
New Crankshaft Position Sensor from 1AAuto.com 1aau.to/ib/1AECS00121
This video shows you how to install a new crankshaft position sensor from TRQ on your 2003-2008 Honda Pilot. The crankshaft position sensor is an important component of any electronically controlled ignition system. The sensor provides the computer with data about the position of the crank shaft to properly adjust ignition timing. If the sensor in your vehicle is broken or malfunctioning, you may suffer poor performance, or get a check engine light.
Once the sensor is installed, you will need to follow the relearn procedure. This can either be done with a manufacturer scan tool, or manually with the following procedure:
1. Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on.
2. Test-drive the vehicle on a level road: Decelerate (with the throttle fully closed) from an engine speed of 2,500 rpm down to 1,000 rpm with the transmission in 2 position.
3. Test-drive the vehicle on a level road: Decelerate (with the throttle fully closed) from an engine speed of 5,000 rpm down to 3,000 rpm with the transmission in 2 position.
4. Repeat step 2 and 3 several times.
5. Turn the ignition switch OFF.
6. Turn the ignition switch ON (II), and wait 30 seconds.
This process should be similar on the following vehicles:
2003 Honda Pilot
2004 Honda Pilot
2005 Honda Pilot
2006 Honda Pilot
2007 Honda Pilot
2008 Honda Pilot
Tools you will need:
• 14mm Wrench 1aau.to/o5z/1AXAA00010
• 10mm Socket 1aau.to/obrL/1AXAA00017
• 12mm Socket 1aau.to/obNn/1AXAA00015
• 14mm Socket 1aau.to/obNn/1AXAA00015
• 19mm Socket 1aau.to/oatL/1AXAA00043
• Coolant Funnel Set
• Honda Crank Holding Tool
• Trim Tool Set 1aau.to/oamn/1AXXX00006
• Circlip Pliers
• Pliers
• Ratchet 1aau.to/obRK/1AXAA00016
• Torque Wrench 1aau.to/oaVk/1AXAA00044
• Brake Parts Cleaner
• Bungee Cord
• Cloth Rags 1aau.to/oH2/1AXSS00035
• Engine Oil
• Gloves 1aau.to/oaBr/1AXSS00048
• Safety Glasses
• Drain Pan
• Floor Jack 1aau.to/oajr/1AXAA00068
• Jack Stands 1aau.to/o7C/1AXAA00065
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Авто та транспорт
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
Might as well do a full timing belt job (and new water pump, tensioner, pulleys) if you're taking all that apart anyway and draining the coolant.
Why remove the battery and drain the coolant? Not logical, extra work. I do, however, appreciate the video. Nice job.
What’s the reason for draining the coolant taking the top two covers off and removing the power steering pump
this video is great I did my crank position sensor and it was spot on he made it easy
That's a lot of work for the crank sensor. Time for a timing belt change while in there.
great video
This video is wrong. 3.5 engines older than 2005 have a different part and completely different setup inside. Please fix your title.
Where is the relearn procedure?
Is it in the same spot on a 2005 Honda accord hybrid?
+@LuhGregCookedIt The part in this video fits your application, and the install should be the same or similar. Buy this part on 1AAuto.com: 1aau.to/m/Shop-TRQ