There is a REDUX video, be sure to watch it - ua-cam.com/video/NeSMmYN4xRM/v-deo.html Basically M24M02-DR did not work with IJV and was buggy with Reborn, but I fixed it. But if you want this mod to also work with IJV you have to get M24M02-A125 (links in description). But interesting thing to note -- if Alex here can make Reborn firmware copatible with DR chip, without knowing coding and being familiar with the code, that means IJV team can also make their firmware compatible with this chip. In REDUX video I show what I did to fix it. Here is link to the fixed up version: firmware -- t.me/uvk5_spectrum_talk/54231/56454 then apply SSB patch in normal mode -- codepen.io/fagcinsk/full/PogrKrq For me it makes financial sense to get the "wrong" DR chip, because the A125 chip cost as much as radio itself. However, for those of you in the west, just order A125 chip from DigiKey, Farnell, Mouser, links in description.
@@AnatolyShemuratov M24M01-R M24M01-DF datasheet says write byte 5ms, it should work with IJV. By the way. There is REDUX video, I made the DR chip work with Reborn.
@@AnatolyShemuratov Ну да, там куча Китайцев выставляют калибровки под каждую рацию. Всё равно надо сохранять калибровки и конфиги. И ставить. Там профи делали прошивки.
Awesome Mate! Thanks for a great video. I have done the mk1 mod chip and now the M24M01 chip. This is my favourite setup for this radio and I have tried most of them. IJV-3.14, Egzumer 0.22, F4hwn v-2.7, Your video's are great! Thanks again
Awesome video as always. I have the new ver 3 i think mod board with amp and possible two antenna connectors . I think I will order the new memory chip as well. Trouble is you keep making great mods and i can't keep up!
Очень жду видео с доработкой КВ, плата с усилителем для мода КВ v2. Купите жало KF, я только им и работаю. Смд снимаю в один проход. Корпус soic 8 грею сразу 4 ножки приподнимаю, потом грею другую сторону и она сдвигается. Попробуйте, желаю успехов!
Чуйка устраивает? Если нет, тогда 2.1 чувствительней. Тот же FM. Я не знал что у меня в городе есть радиостанция монте карло или радио маяк на 70.200, и куча других станций.
@@codernov I'm looking forward for the easier job just because today, motivated by you, I managed to put the HF kit in place and install the CEC 0.5 HF firmware and it's enough at the moment. I don't think that I'll be able to fiddle with such tiny components one more time, using only a cheap plastic magnifying lens and a soldering gun (the classic transformer type with copper wire tip).
@@VassVince Oh that thing. I hope you at least used flux, flux make solder flow. Yes, tools make job easier. You can do this job with a solder iron from dollar store, the not classic but cheap small chinese type. I think you need solder iron and jewels mask, in total that will be around $5 shipped. You just gave me idea for video. Basic tools! I'll do a video about sound mod. No problem.
Dear Alex, I have a soldering iron with usb charge but the tip is stubbornly solder repellent, stays dirty whatever I do that is why I took the soldering gun instead. Of course I used flux but not the paste or liquid type but the solid one from pine sapp. Thank you for meeting my demands regarding the videos, I will surely follow your updates!
Hello Codernov: I accidently (when I took apart my K6, pulled the red/black speaker wires from the motherboard where it was soldered together. Would I use "Tin Lead Rosin Core" 0.8mm soldering wire to reconnect it?
Solder back with whatever solder you have, apply some flux so solder flows. It happens all the time, you disassemble the radio and wires tend to come off themselves, sometimes.
So what you do first is back up your calibration & config using k5prog-win. Then you install telegram messanger, and go to this link. t.me/uvk5_spectrum_talk/51068/58488 It will open up the link in telegram messenger and you will see the file. You right click it, and save it as to your desktop. What you probably did is just click it, and that way it would save it to your downloads folder, that's why you lost. But be sure to back up your calibration & config!
Hi, i see all your videos but I am a bit confused, can you confirm wich one chip is the best to buY ( to flash these modified firmwares) the M24M02-DRMN6TP or the M24M02-DWMN3TP/K, or the 24M02RD K315K? (this is the last one that you install in your last video) Thank you very much again!
After you swap it out you should press PTT and turn on your radio, and put new firmware on. Any will work. However, only few take full advantage of it. Reborn WFM SI SSB for example.
@@codernovThat's what I intend to install once I have fitted the HF board or can I try it before?. Is a blank screen normal after swapping the EPROM? I tried loading the calibration files and 1of11 firmware, they loaded ok but still no screen ?
Holding down a key while turning it on brings up the display 'release all keys' so the screen works at least - I'll load the reborn firmware and do the EPROM clear, see if that helps. I'll head over to Telegram - Thanks and great videos!
@@MercZeroSeven I have no clue what is happening with you, problems that I never faced. You'd have to go to uvk5_spectrum_talk and in general section post some pics.
Hi. I have a question about low melting point solder. what is its melting point, what is its composition and under what name can it be bought? I love watching your videos and learning your skills. Thank you for your response. Dezider.
Rose's metal is the one I use, but there are others. If you go to eBay and look for "rose's metal" you will find it. It's 98C, 50% Bi 25% Pb 25% Sn. On amazon look for low melt. Also DigiKey, Farnell, Mouser, and don't forget your local electronics supply store. I pay $3.50 for 100 grams here.
I have followed your instructions on installing the Fagci Firmware and all seems to work. Exept when i go to the SI47XX menu i can listen in monitor mode on the FM and AM bands, but as soon as i go to the LSB and USB bands, its impossible to open up the squelch to listen in . i haven't found any information how to change this . Could you tell me how this works on the SSB bands?
That's because I haven't provided you with instructions for SSB. After you install firmware, you have to apply patch. You connect radio via cable in regular mode with radio just on, and you go here codepen.io/fagcinsk/pen/PogrKrq , and click Connect and then click Apply SSB Patch. After it's done, you disconnect cable and reboot radio. Then your SSB will work.
@@Elaba83 Let's track back and do everything again from the start. In video description you have link to firmware, download it. Using k5prog-win install firmware. Turn off radio. Press and hold 7 key and turn on radio. After 0xFFing done, turn off radio. Press and hold EXIT key and turn on radio. After everything is done, turn off radio. Turn radio back on. Go to that link and apply the patch. Turn radio off. Turn radio on. Short press M key and select Si47xx. You will enter FM mode. Click 0 key to go into AM mode. In AM mode there will be sound, static. Hit 0 key one more time and you will enter SSB mode, there will be sound, static. Now you hit the F key for LSB or USB. For this to work you need to have both Si4732 and larger EEPROM. Try it one more time, retrace your steps.
@@codernov About 2 weeks ago, i had the firmware working on SSB, without the Patch. But the performance was worse compared to the CEC 0.5 firmware. So I flashed back to CEC without performing the "uninstall" procedure. Now since the patch is available, I followed your instructions again and also did the patch. Exactly like you discribe the steps above. Perhaps I need to do the uninstall procedure aswell before starting over?
Right now to use LSB & USB in Reborn, you need larger EEPROM. Patch does not fit onto stock 8 kbyte EEPROM. You could go with CEC for that, but it is cut up so that SSB fits. So to use Si4732 and still have fully functional radio you need Reborn and you need larger EEPROM -- which is no problem, $1.62 for 2 chips. Like I said, it's not about number of channels.
Correction! We found a problem. The chip you need is M24M02-DWMN3TP/K. I included whole bunch of links to the correct chip in video description. The chip you asked about with K436K marking is the wrong one, IJV won't work and Reborn will be buggy with it.
There is a REDUX video, be sure to watch it - ua-cam.com/video/NeSMmYN4xRM/v-deo.html
Basically M24M02-DR did not work with IJV and was buggy with Reborn, but I fixed it. But if you want this mod to also work with IJV you have to get M24M02-A125 (links in description). But interesting thing to note -- if Alex here can make Reborn firmware copatible with DR chip, without knowing coding and being familiar with the code, that means IJV team can also make their firmware compatible with this chip. In REDUX video I show what I did to fix it. Here is link to the fixed up version:
firmware -- t.me/uvk5_spectrum_talk/54231/56454
then apply SSB patch in normal mode -- codepen.io/fagcinsk/full/PogrKrq
For me it makes financial sense to get the "wrong" DR chip, because the A125 chip cost as much as radio itself. However, for those of you in the west, just order A125 chip from DigiKey, Farnell, Mouser, links in description.
@@AnatolyShemuratov M24M01-R M24M01-DF datasheet says write byte 5ms, it should work with IJV. By the way. There is REDUX video, I made the DR chip work with Reborn.
@@AnatolyShemuratov Вы IJV будите пользоваться?
Надо ставить Карину. t.me/k5fwmod на одну рацию а на вторую Reborn t.me/uvk5_spectrum_talk/
@@AnatolyShemuratov Ну да, там куча Китайцев выставляют калибровки под каждую рацию. Всё равно надо сохранять калибровки и конфиги. И ставить. Там профи делали прошивки.
Awesome stuff!
Thank you for continuing the Quansheng upgrading!
Awesome Mate! Thanks for a great video. I have done the mk1 mod chip and now the M24M01 chip. This is my favourite setup for this radio and I have tried most of them. IJV-3.14, Egzumer 0.22, F4hwn v-2.7, Your video's are great! Thanks again
Forgot to mention....CEC 0.51
Another great video man !
Keep on modding our hadware 😊
Awesome video as always. I have the new ver 3 i think mod board with amp and possible two antenna connectors . I think I will order the new memory chip as well. Trouble is you keep making great mods and i can't keep up!
Очень жду видео с доработкой КВ, плата с усилителем для мода КВ v2.
Купите жало KF, я только им и работаю. Смд снимаю в один проход. Корпус soic 8 грею сразу 4 ножки приподнимаю, потом грею другую сторону и она сдвигается.
Попробуйте, желаю успехов!
Video is for average guy, without the KF. That mod will be in my hands next week. Already left Domodedovo.
Видео уже загружено
@@codernov вчера уже посмотрел)
У меня есть плата зеленая, вот думаю нужно ли ставить с усилителем версии 2,1.
Чуйка устраивает? Если нет, тогда 2.1 чувствительней. Тот же FM. Я не знал что у меня в городе есть радиостанция монте карло или радио маяк на 70.200, и куча других станций.
@@codernov новых станций я не нашел)
Proffesional as usual. I'm curious about the volume enhancement modification too. Thank you and keep working brother🫡
You mean adding caps and stuff to sound amp, or are you talking about shorting a resistor to increase volume in Si4732 mod?
@@codernov I'm looking forward for the easier job just because today, motivated by you, I managed to put the HF kit in place and install the CEC 0.5 HF firmware and it's enough at the moment. I don't think that I'll be able to fiddle with such tiny components one more time, using only a cheap plastic magnifying lens and a soldering gun (the classic transformer type with copper wire tip).
@@VassVince Oh that thing. I hope you at least used flux, flux make solder flow. Yes, tools make job easier. You can do this job with a solder iron from dollar store, the not classic but cheap small chinese type. I think you need solder iron and jewels mask, in total that will be around $5 shipped. You just gave me idea for video. Basic tools! I'll do a video about sound mod. No problem.
Dear Alex, I have a soldering iron with usb charge but the tip is stubbornly solder repellent, stays dirty whatever I do that is why I took the soldering gun instead. Of course I used flux but not the paste or liquid type but the solid one from pine sapp. Thank you for meeting my demands regarding the videos, I will surely follow your updates!
Crappy tip then, you could use Mechanic N6 tip cleaner.
Hello Codernov: I accidently (when I took apart my K6, pulled the red/black speaker wires from the motherboard where it was soldered together. Would I use "Tin Lead Rosin Core" 0.8mm soldering wire to reconnect it?
Solder back with whatever solder you have, apply some flux so solder flows. It happens all the time, you disassemble the radio and wires tend to come off themselves, sometimes.
Another kick ass video Alex!! Do you happen to know where I could find a schematic for this radio?
github.com/2ftg/UVK5_reversing
@codernov Your the man!!! Thanks
have you tried the M24512E-F 512Kbit Serial I²C BUS EEPROM?
Nah. If you have it laying around, put it on, and install r3b0rn, see if it works.
I tried to download the bin file from telegram... not familiar with that. I do not seem to be able to download from there. ... help?
So what you do first is back up your calibration & config using k5prog-win. Then you install telegram messanger, and go to this link. t.me/uvk5_spectrum_talk/51068/58488 It will open up the link in telegram messenger and you will see the file. You right click it, and save it as to your desktop. What you probably did is just click it, and that way it would save it to your downloads folder, that's why you lost. But be sure to back up your calibration & config!
Love this upgrade Rambo, but when they start selling these upgraded radios with shortwave
Rambo is from Bragg, I'm not from Bragg
@@codernov 😂😂, but will he sell modified radios?😉
🙏👍👍👍👍👍👍👍
Hi, i see all your videos but I am a bit confused, can you confirm wich one chip is the best to buY ( to flash these modified firmwares) the M24M02-DRMN6TP or the M24M02-DWMN3TP/K, or the 24M02RD K315K? (this is the last one that you install in your last video) Thank you very much again!
Don't be confused, M24M02 search on ali, and first thing that comes up, you but that one.
Will any firmware still work with an M24M02 - I swapped it out and now have a blank screen ? 1 of 11 is in there at the moment ?
After you swap it out you should press PTT and turn on your radio, and put new firmware on. Any will work. However, only few take full advantage of it. Reborn WFM SI SSB for example.
@@codernovThat's what I intend to install once I have fitted the HF board or can I try it before?.
Is a blank screen normal after swapping the EPROM?
I tried loading the calibration files and 1of11 firmware, they loaded ok but still no screen ?
Holding down a key while turning it on brings up the display 'release all keys' so the screen works at least - I'll load the reborn firmware and do the EPROM clear, see if that helps.
I'll head over to Telegram - Thanks and great videos!
@@MercZeroSeven I have no clue what is happening with you, problems that I never faced. You'd have to go to uvk5_spectrum_talk and in general section post some pics.
Hi. I have a question about low melting point solder. what is its melting point, what is its composition and under what name can it be bought? I love watching your videos and learning your skills. Thank you for your response. Dezider.
Rose's metal is the one I use, but there are others. If you go to eBay and look for "rose's metal" you will find it. It's 98C, 50% Bi 25% Pb 25% Sn. On amazon look for low melt. Also DigiKey, Farnell, Mouser, and don't forget your local electronics supply store. I pay $3.50 for 100 grams here.
@@codernov Thank you for the quick reply . ✌
I have followed your instructions on installing the Fagci Firmware and all seems to work. Exept when i go to the SI47XX menu i can listen in monitor mode on the FM and AM bands, but as soon as i go to the LSB and USB bands, its impossible to open up the squelch to listen in . i haven't found any information how to change this . Could you tell me how this works on the SSB bands?
That's because I haven't provided you with instructions for SSB. After you install firmware, you have to apply patch. You connect radio via cable in regular mode with radio just on, and you go here codepen.io/fagcinsk/pen/PogrKrq , and click Connect and then click Apply SSB Patch. After it's done, you disconnect cable and reboot radio. Then your SSB will work.
By the way. You can only apply that patch if you have updated EEPROM. Patch won't fit onto stock EEPROM.
@@codernov I have the M24M02 eeprom, and just run the patch, but SSB is still not working...
@@Elaba83 Let's track back and do everything again from the start. In video description you have link to firmware, download it. Using k5prog-win install firmware. Turn off radio. Press and hold 7 key and turn on radio. After 0xFFing done, turn off radio. Press and hold EXIT key and turn on radio. After everything is done, turn off radio. Turn radio back on. Go to that link and apply the patch. Turn radio off. Turn radio on. Short press M key and select Si47xx. You will enter FM mode. Click 0 key to go into AM mode. In AM mode there will be sound, static. Hit 0 key one more time and you will enter SSB mode, there will be sound, static. Now you hit the F key for LSB or USB. For this to work you need to have both Si4732 and larger EEPROM. Try it one more time, retrace your steps.
@@codernov About 2 weeks ago, i had the firmware working on SSB, without the Patch. But the performance was worse compared to the CEC 0.5 firmware. So I flashed back to CEC without performing the "uninstall" procedure. Now since the patch is available, I followed your instructions again and also did the patch. Exactly like you discribe the steps above. Perhaps I need to do the uninstall procedure aswell before starting over?
More channels is not really interesting. What would be interesting (for me) is more letters for channel names.
Right now to use LSB & USB in Reborn, you need larger EEPROM. Patch does not fit onto stock 8 kbyte EEPROM. You could go with CEC for that, but it is cut up so that SSB fits. So to use Si4732 and still have fully functional radio you need Reborn and you need larger EEPROM -- which is no problem, $1.62 for 2 chips. Like I said, it's not about number of channels.
Hi. Does it matter the chip has different markings after M24M02-DR? I can only get the 'K436K' ones?
-You'll be fine- Proper chip is M24M02-DWMN3TP/K, the M24M02-DRMN6TP is the wrong one.
Correction! We found a problem. The chip you need is M24M02-DWMN3TP/K. I included whole bunch of links to the correct chip in video description. The chip you asked about with K436K marking is the wrong one, IJV won't work and Reborn will be buggy with it.
@@codernov Thought so. Thanks for letting me know.
First!