How to Install 2019 Ford Ranger Tail Light & Backup LEDs | Diode Dynamics
Вставка
- Опубліковано 10 лип 2024
- Get your LED Backup Light Bulbs here: www.diodedynamics.com/backup-...
Get your LED Tail Light Bulbs here: www.diodedynamics.com/tail-li...
Get your LED Rear Turn Signal Bulbs here: www.diodedynamics.com/rear-tu...
Get your LED Resistor Kit here: www.diodedynamics.com/led-res...
Check out our Resistor Kit installation video here: • How to Fix Hyperblinki...
How do we test and measure products? Learn more here: www.diodedynamics.com/product...
0:00 Introduction
0:32 Removing Taillight Housing
1:10 Installing LED Tail/Brake Light Bulb
1:45 Testing Tail/Brake Light Bulb
2:15 Installing LED Turn Signal Bulb
2:22 Installing Resistor Kit
2:47 Installing LED Reverse Light Bulb
3:11 Re-Installing Tail Light Housing
3:42 Summary
This video highlights the easy installation steps for Diode Dynamics LED Rear Turn Signal, Tail, and Backup Light Bulbs for the 2019 Ford Ranger. Unlike generic LED replacements, our Tail, Rear Turn Signal, and Backup Light LEDs are engineered and tested in the U.S.A to ensure maximum brightness and reliability.
At 510 test-proven lumens, our XP80 LED Backup Light Bulbs are some of the brightest on the market! With these installed, your Ranger will produce MUCH more rear-facing light output, making reversing at night far easier and safer. Best of all, installation is 100% plug-and-play!
Similarly, our XP80 LED Tail Light Bulbs also produce 510 test-proven lumens! Drastically brighter than stock, the XP80 makes your 2019 Ford Ranger much easier for other drivers to spot when braking.
Last but not least, Diode Dynamics LED Rear Turn Signal Bulbs not only make your turn signals and hazards more visible, they also give your 2019 Ford Ranger a more modern look, thanks to the instant on/off of the LEDs. Our 510 lumen XP80 LED bulbs are also available for the 2019 Ranger's rear turn signals, and is dramatically brighter than the factory halogen bulb!
Email us with any questions at contact@diodedynamics.com or call 314-205-3033. Thanks for watching!
Products shown:
DD0113P
DD0109P
DD0116P
DD0111P
DD0107P
DD0114P
DD0112P
DD0108P
DD0115P - Авто та транспорт
The 21 model doesn’t have the same tail lights they have a plate and I don’t know what to do from there
Sorry to hear you're having some troubles! Feel free to give us a call at 314-205-3033 Monday-Friday 10 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com, and our in-house US service team would be happy to help you with that.
So when the lights go out I don’t have to buy a new tail lamp? All I do is just replace the light bulb? Is that the same for front?
This is for the USA model. **edited
I ordered the 510 lumin reverse lights kinda excited for them to arrive. I need a life
There's nothing wrong with being excited about car parts, Robert!
so my 2019 ranger has the blind spot sensor. Do these bulbs still work? I can't figure out how to access the individual bulbs
Yes, they do! Please reach out to us at contact@diodedynamics.com, or give us a call at 314-205-3033 M-F CST, and our service team will be happy to help!
@@diodedynamics you guys emailed me and said they wouldnt work because my bulbs are encased
@@stephensturges5711 If you already have the fancy LED tail light housings, why are you looking for bulbs?
@@silverapple2011 couldnt remember if my lights were led or not
Will I need a resistor for any of the brake lights ? Thanks I have a 2020 Ranger.
Nope- you shouldn't need a resistor!
My tail light is different than this one on my 2019 ranger I can’t see all of the bulbs from the back
If I have a resistors on my 2019 Ranger front switchback turn signals to correct interior console hyper flashing/blinking, do I need to install resistors for the rear turn signals too?
Yes, you more than likely will also need them in the rear, Eddie.
Hi! I just bought a 2021 ranger raptor, would the stop light, turn signal and back up leds will need resistors? regards
The only LED upgrade location that would require our LED resistor kit would be your turn signal location.
Hi, i installed the turn signals to my 2021 ranger raptor and they work just fine (no rapid flash) but inside of the vehicle in the dashboard the turn signals blink like there was a problem (even tho on the out side they work fine). Does resistors fix the hyperflash on the dashboard?
Resisters should fix this issue. Because the LEDs draw so much less power than the halogen bulbs, the computer thinks the factory bulb is out. Installing resistors would be a great place to start!
I have led taillights in my XLT but received smoked ones how to remove this taillight?
Hey there! We don't quite understand your question. Would you mind further explaining?
I have the xlt with cross traffic and blind spot. My casjng looks completely different. Any pointers?
Hi Mario! These should fit the XLT model as well. However, please shoot us an image of your tail light housing to contact@diodedynamics.com, and we will look into this for you!
Were you able to switch your lights, Mario? Mine has the blind spot detector, too. If you did change your lights, was it difficult?
Do I need a resistor kit for a 2019 xlt Ford ranger?
Hi Jamey! No, you won't need resistors for the Tail or Backup Lights!
So all of these are t20 from rear stop light, turn signals and reverse? I'm confused with the codes that says w21w, w21/5w etc
Hey Jeriel! Please check out the link below. It is all the bulbs you'll need for your Ranger. It gets a bit confusing. Bulbs have several cross-references.
www.diodedynamics.com/by-vehicle.html?find=2019-ford-ranger-379058&sid=gqHq7AYkLo
My tail light assy has one harness plugged in and all the bulbs are incased??....will these still work?
Based on what you have described, it does sound like factory LED. If you have factory LED, you would be unable to change the bulbs over to LED.
@@diodedynamics yeah but you would still need access if you had to replace a led bulb
How do i remove the dome light cover to repleace the bulb???
Xl 2019 ranger
@@beemcampos513 Go ahead and reach out to us at contact@diodedynamics.com for help with any troubleshooting- thanks!
Will this work on an XLT?
As long as you do not have factory LED options back there - absolutely!
Will I need to add a resistor on xl model.
Hey Javier! You will need a resistor for any LEDs that are installed on the turn signal circuit to avoid hyper-flashing. If you have any other questions, just give us a call at 314-205-3033, Monday-Friday 9 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com!
Hyper flash is super annoying I just put resistors in my ranger👍🏿
? for ya, are the taillight led bulbs red in color or is it just the effect of the taillight lens? Reason I ask is because I have a light smoke taillight lens tnx
In this case, the tail light is a red XP80 bulb.
@@diodedynamics what about the hp48 and hp11 bulbs, do they emitt a red light?
@@petemilliet9694, we do also offer those in red options as well!
sucks the 2020 version is different and I cant find anything on how to change it anywhere.
The installation process should be the same for the 2020 model.
@@diodedynamics I just found out what the issue was. the 2020 XLT has a closed LED system that cant be changed which makes sense because it looks totally different than the one in your video and instead of having the 3 separate bulbs in a row it has one and you can't remove it to change the bulb its fixed into the light enclosure to where you cant take it out.
@@dmannion81 Ahh- Yes, 2020 XLT models did come with LEDs from factory. We should have mentioned this before. Sorry about that!
Any discount codes?
We're actually currently running our Memorial Day Sale! Be sure to check it out on our Social Media!