2019+ Ford Ranger Install AUXITO LED Switchback White/Amber Turn Signal Lights
Вставка
- Опубліковано 3 чер 2021
- We install Auxito Led Switchback Bulbs on my 2019 Ford Ranger!
Subscribe to the channel!
Thanks for watching!
Get yourself a set for your Ford Ranger
auxito.com/?ref=e6dmzabg2l
auxito.com/collections/7443a/...
Follow us on Instagram
/ thewiscoguyz - Авто та транспорт
a trick i found when I was doing the high and low beam replacement was remove the two screws from the intake and remove it lots of room now hop this helps
your ranger is coming along real nicely keep up the good work with it
Yes I'll be getting a set of them that's sweet I really like them
Just installed mine and yeah definitely a home run now I'm going to do the fog lights and headlights great video
Good video just ordered some with your link
Glad you liked the video! Thanks for watching!
Are you going to do anything about putting LED headlights if so I can't wait to see the video if you do
Might be doing this soon, we will see
looking good, I just made an order. Did you have to install any resistors for hyperflash?
Nice! I did install resistors, but unfortunately they don't offer them anymore.
Will this work with the XL. I have an STX package and have the same headlights as the XLT
Should be the same bulbs
Did you put a resistor to elimate the hyperblink?? Or its ok not putting a resistor??
Working in getting one installed... Should have a video on it here in a week or two.
Oh man I got these pulled my drivers side out plugged the new one in..apparently it didn't set just right and I think it fell in the blinker housing uggh how would I go about getting that back out of there? I was thinking magnet but would that ruin it?
Might have to take the whole headlamp out... 😳
I replaced the stock turn signal bulbs with Auxito LED bulbs. The outside flashes as normal but the inside blinker is hyper flashing. The LED kit came with a resistor but I'm wondering if the outside bulbs are flashing normally, do I just need to replace the blinker/flasher? I don't want to put in the resistor and then the outside bulbs flash abnormally.
When I put the resistors in the truck for the turn signal bulbs the blinker work normally outside and on the dash
Check this video out of the install of the resistors for the front blinker bulbs. ua-cam.com/video/mqT6EZEae3A/v-deo.html
@@TheWiscoGuyz Okay, I just ordered them. I wanted to find the exact same one you demonstrated. Thanks.
Can’t find these on Amazon, did they change the item or part # ?
go to there website. auxtio.com
How does this work when the low beam headlight is your DRL? This is what my 2021 Ranger has.
Should work the same... I turned my DRL off in the setup menu. I have to turn on the light for them to be on.
@@TheWiscoGuyz Oh great. Didn't know that could be done. Thanks.
Thanks for watching!
Purchased same bulbs for 2022 Ranger lariat and the switchback doesn’t work. They flash amber for turn signal but not white when not in turn signal mode. The old bulbs have two filaments but they do not light up as marker lights either, even after disabling daytime running lamps in menu and manually turning on lights. Strange. My headlight assemblies are different from yours as mine have led light strips as daytime running lights and projector headlight bulbs. Any thoughts fellow cheesehead?
Yes I believe they will not work with the lariat headlight housing... Because there is no power to the turn signals when the turn signals are not on. They put that power to the led strips on the lariat models
Great to know. Will keep the switchback bulbs in though. At least if a diode burns out I still have turn signal. Thanks again.
Clue me in on your signal lens being white or clear, on my ‘19 XL they are amber, what trim package do you have? Thanks.
I had the XLT package. The xl package come with a yellow lens from factory.
@@TheWiscoGuyz Ahhh I'm embarrassed I didn't notice, 😕
so there's 3 different headlight assemblies, I set my parks in Forscan to be DRL's and I wanted them to be white, hmm I guess not lol. Thanks for the reply, i enjoy your vids.
Thanks for watching
Have you installed a resistor?
Not yet, but i do have them and i will be doing a video shortly.
,@@TheWiscoGuyz please share. If I command the lights, will I get a resistor, or do I have to ask for it?
Now if I could eliminate the the headlights from coming on when shifting into drive.
There is a way to disable it in the settings menu.... but if the truck is Canadian then you can't
@@TheWiscoGuyz ok so my truck was built in Michigan but I think registered in Canada. Has linex from Calgary but I bought it used in Washington lol. Only had 3k on it
@@StormShadowX37 best way to tell if it's from Canada there should maple leaf on the vin tag in the front door jam.. then you know it's Canadian.
@@TheWiscoGuyz 😢I see 2 different maple leaf
Is the socket size standard or ck?
Metric
@@TheWiscoGuyz I'm trying to do the switch back bulb s and I have a 2021 ford ranger and the guy I have to look if the bulb is standard or ck
Fit to ranger 2022
Yes