Rain Bird ESP-ME3 Advanced Programming

Поділитися
Вставка
  • Опубліковано 1 кві 2019
  • Step by step guide to the advanced programming features of the Rain Bird ESP-ME3. Learn how to customize your watering schedule and take advantage of the controller's most advanced water saving features.
    Shop Rain Bird Online: store.rainbird.com/
  • Навчання та стиль

КОМЕНТАРІ • 31

  • @Mr.Nogijiujitsu
    @Mr.Nogijiujitsu 3 роки тому +2

    This was super helpful

  • @dginta7932
    @dginta7932 3 дні тому

    Is the program glitchy for Android phones? I can’t get the zones to show up on two different Android phones but it loads fine on IPads.

  • @user-de6zy1oj8s
    @user-de6zy1oj8s 10 місяців тому

    Can you alternate zones and days? Example Zone 1 and 2 waters Monday, Zone 3 and 4 on Tuesday, Zone 1 and 2 waters Thursday, Zone 3 and 4 on Friday?

  • @ausguy4385
    @ausguy4385 3 роки тому

    Got a new wifi⁶ router and now it sees the new router but claims not good enough signal dispite it being full for any other device.
    It's the same distance for the old router so it not that.
    Will you be doing a firmware update anytime? As new routers are all wifi⁶....

  • @pedrobarajaslopez6772
    @pedrobarajaslopez6772 3 роки тому +1

    How to ad time to sectin

  • @jtatherton7627
    @jtatherton7627 2 роки тому +1

    How do you bypass the Cycle days in order to water every evening? Seems like the Cycle day minimum setting is 2 days? Why can't this be set to "0" or turned off completely if wanting to water every evening??

    • @michaelshafer3377
      @michaelshafer3377 Рік тому

      Did you find the answer you were looking for? I had/have the same issue. I may have solved this issue, just set it this morning so I'm not sure if it is working as I want, watering every day. When in auto, press and hold the + key until 'Delay 1' pops up. Then hit the - key and for a fraction of a second, it says delay 0, then reverts to auto. Hope this works for you because that should mean it is working for me. I'll watch it for a few days and see.

  • @shelleyackermann9275
    @shelleyackermann9275 Рік тому

    I need to add a watering cycle for only certain zones (some to water twice and others to water three times/day). How do I accomplish that with the programming? Or will I just have to do it manually?

    • @JohnMiller-iu2sx
      @JohnMiller-iu2sx Рік тому

      Pick an unused program A,B,C,or D.
      Set a start time.
      Pick your zones (set zone run time?) And add time
      Set days of the week to water
      Put controller on Auto.

    • @JohnMiller-iu2sx
      @JohnMiller-iu2sx Рік тому

      Zones that need 2 start times can be on one program
      Zones that need 3 start times will need another program

  • @jenny6173
    @jenny6173 Рік тому

    so we had a new controller installed and it was working fine...then we had a power surge and the transformer blew.....we had another controller installed but since then it's not working properly. the pump keeps clicking in and the pressure is low ....any idea what could be the problem

    • @JohnMiller-iu2sx
      @JohnMiller-iu2sx Рік тому +1

      I would get a cyliniod wire it direct to the controller turning it on zone by zone and listening for the cyliniod to click/hum. Confirming that's good, you may need to replace the pump start relay

  • @kevinarias451
    @kevinarias451 3 роки тому +1

    Can you start them all at the same time??

    • @JohnMiller-iu2sx
      @JohnMiller-iu2sx 3 роки тому +5

      No. In most residential applications you would kill water pressure if you could.

  • @jimtube5219
    @jimtube5219 3 роки тому

    Can I adjust the readout brightness?

    • @JohnMiller-iu2sx
      @JohnMiller-iu2sx Рік тому

      No. (In case anyone else has the same question)

    • @jimtube5219
      @jimtube5219 Рік тому

      @@JohnMiller-iu2sx Correction, Thanks John. Tube reply is not working properly.

  • @sidneywhite749
    @sidneywhite749 4 роки тому +1

    How to start watering now

  • @JohnMiller-iu2sx
    @JohnMiller-iu2sx 9 місяців тому

    3:41 master valve

  • @JohnMiller-iu2sx
    @JohnMiller-iu2sx 2 роки тому

    Rain Delay: 2:08

  • @LasryLikeMaroto
    @LasryLikeMaroto 3 місяці тому

    Gostei!
    Tem como assistir traduzido em português?
    Taí o like maroto!!!!

  • @JohnMiller-iu2sx
    @JohnMiller-iu2sx Рік тому

    0:26 watering days

  • @JohnMiller-iu2sx
    @JohnMiller-iu2sx 3 роки тому

    Master valve: 3:42

  • @MarcyJsplayground
    @MarcyJsplayground Рік тому

    After a $180.00 water bill, I am here. Thank you soooo much for this informative video. Question: I had Start times at 6a, 615a, 630a, 645a…running each station (4 stations) for 10 mins each. I did not realize for each start time, it is actually a FULL cycle of the 4 stations …am I correct in this? So now, I just programmed ONE start time with the intention that all stations will run ONE time. Is this correct? Lesson learned. Thank you so much, again

    • @RainBirdCorporation
      @RainBirdCorporation  Рік тому +1

      Thank you for contacting Rain Bird! Yes, you are correct. Each start time is an entire full cycle. Yes, you only need to set up the 1st start time for it to water once a full cycle.

    • @rhysdecallier4329
      @rhysdecallier4329 Рік тому

      Thank you. So to clarify. If I have 7 stations I only need to set the start time for station 1 (5am). Set all others to “off”. Then I would set the run times for all 7 at say 30 mins? Then all would run once beginning with The first station at 5am with station 7 finishing at 8:30am?

    • @RainBirdCorporation
      @RainBirdCorporation  Рік тому +2

      Hi Rhys! That is accurate, you only need one start time to run through all your stations for 30 minutes.

    • @RedHaloManiac95
      @RedHaloManiac95 Рік тому

      That’s it? Mine was 300 something 😂

    • @MarcyJsplayground
      @MarcyJsplayground Рік тому

      @@RainBirdCorporation thank you sooo much!

  • @mdarifulmola
    @mdarifulmola 22 дні тому

    বাংলা ভাষা