About to do this repair on my 3rd gen 2500, went ahead and got the red head gear box, first time replacing the OEM box after 247k miles she finally gave out boys! Going to use this vid as guidance. Thanks!
Those fittings on the top of the box are 18mm. The pitman arm nut is a 1-5/16". It is easier to remove the wheel well liner and remove all the fittings from the top first so you don't kink the hard line while letting it hang like that.
I used to teach aircraft mechanics. Your video as opposed to others was slow enough for the novice and informative enough for the more knoledgeable. Over all very well done. You showed patience with the process. Only suggestion is, and I understand from your description someone else had been there before on the hydraulic lines and did not use the proper tools which rounded off the nuts on the tubes, is that you suggest that one uses the proper hydraulic fitting tools so as not to round off the nuts. Well done!!!!!!! Martin Btw I have a masters in engineering in aeronautics. I rarely give a compliment and you did very well. I would trust you with my vehicle.
Doing mine again currently for the 3rd time. I keep 1 of the 3 bolts holding the box to the frame in then get the lines removed up top, steering shaft, then loosen the last bolt and everything is unhooked and you can remove the box. A lot easier IMO. Great video!
@@Daland21648 order a redhead or ‘blue head or blue top’ gear box. Not sure what year yours is, if it’s a 3rd gen, I’d recommend a 6 bolt steering gear box. Just replaced my steering shaft with a borgeson also and have a lot of play. It’s my gear box too.
@@Daland21648 you’re welcome! Yeah any 4th gen 6 bolt gear box will help drastically. Doing that next on mine. Rebuilt everything else. Literally everything 😂
Just realized you were making videos again. UA-cam had you at the bottom of my recommended list due to the hiatus a few years ago but I'm putting you back at the top! One of my favorite channels!
Recently did this on my '96... after heating/beating/penetrating oil, slotted the pitman arm with a grinder to get it off... moving to "step 3" sooner would have saved time! Thanks for the video!
Time to upgrade the drag link and tie rod on that truck, the 08.5 steering linkage is much beefier and gets rid of death wobble... Good how to video :)
Didn't get rid of my wobble. Nothing did until I did it all. The linkage, ball joints, shocks, gear box, steering shaft, pump and lines (the pump was toast to) I've dealt with that damn wobble for six years. Finally got fed up with chasing the problem. The problem isn't one thing, it's combination of parts. If one is worn, then it wears the new parts faster and that's why the wobble kept coming back.
@@maddawgnoll yup, most ppl naively think its one thing but its not, i was one of them. But all parts have to be very well worn in so they all can get in harmony and oscillate. Deathwobble gets annoying, having to avoid certain parts of the street or "better slow down just to XX mph"
So the arm attached to the steering gear box doesn't need to be flush just tight as humanly possible. Also disconnected the steering shaft before turning the wheel back and fourth to bleed the lines. Unless you have a lift like these gents
I wonder what causes continuous bubbling in the reservoir...? Changed the pump along with the pulley when it started leaking, but it did bubble from the start and then the other day I had no power steering. Never sloppy, no noises, never stiff, just turned on tractor manual steering one day. Steering gearbox says my mechanic now. What next...? Scrap it I guess. 🙄
Just waiting on the pitman arm removal tool which Amazon says I will get tomorrow then my the new PSC steering box goes in my 98 12V using this as a guide.
Yes they do, I went with a PSC box. MUCH better than the Red Head it replaced and totally worth the cost. Funny thing the PSC non hydro box is cheaper than OEM and much stronger.
@@edzgarage does the top of that arm you bolted on the sector shaft fit flush with the bottom of the sector box? Or is there space between the two where part of the spline is visible? I just had a shop put a box on my dodge and noticed a gap exposed and could see the spindle or spline whatever it’s called.
Smashing job :-D, Zack made it look easy, that pitman arm and control rods look heavy duty, the weak spot i assume is the box, and perhaps the universal joint to the steering shaft/wheel. It should have very little slop in the wheel now :-) I hope there was at least one swear word off camera, it's just not a "propper repair" without one :-D.
Steering is crisp and tight. Those reman parts don't last tho, that's why they have "lifetime" warranty. They know us really well at the parts store :-) If there's even a hint of play it goes back for another one.
Hi edz, Ive got the gear box changed by a garage. When i drove home I noticed the steering wheel is 15degr left, it is related to this operation? I asked them to align it and they refused,claiming that it is normal and should pay extra to fix it. Please advise.
About to do this repair on my 3rd gen 2500, went ahead and got the red head gear box, first time replacing the OEM box after 247k miles she finally gave out boys! Going to use this vid as guidance. Thanks!
Those fittings on the top of the box are 18mm. The pitman arm nut is a 1-5/16". It is easier to remove the wheel well liner and remove all the fittings from the top first so you don't kink the hard line while letting it hang like that.
One fitting is 18mm, the other is a 21mm right? Mine were on my 06 Atleast
Thanks
I used to teach aircraft mechanics. Your video as opposed to others was slow enough for the novice and informative enough for the more knoledgeable. Over all very well done. You showed patience with the process. Only suggestion is, and I understand from your description someone else had been there before on the hydraulic lines and did not use the proper tools which rounded off the nuts on the tubes, is that you suggest that one uses the proper hydraulic fitting tools so as not to round off the nuts.
Well done!!!!!!!
Martin
Btw I have a masters in engineering in aeronautics. I rarely give a compliment and you did very well. I would trust you with my vehicle.
Doing mine again currently for the 3rd time. I keep 1 of the 3 bolts holding the box to the frame in then get the lines removed up top, steering shaft, then loosen the last bolt and everything is unhooked and you can remove the box. A lot easier IMO. Great video!
I’m getting my redone again as well. I just got it done in may 2021…. Any reason why this keeps happening on my ram 2500 diesel ?
@@Daland21648 order a redhead or ‘blue head or blue top’ gear box. Not sure what year yours is, if it’s a 3rd gen, I’d recommend a 6 bolt steering gear box. Just replaced my steering shaft with a borgeson also and have a lot of play. It’s my gear box too.
@@Coxie1996 yes it’s a 3rd thanks for the help.
@@Daland21648 you’re welcome! Yeah any 4th gen 6 bolt gear box will help drastically. Doing that next on mine. Rebuilt everything else. Literally everything 😂
Disconnect all lines and steering linkage First, no matter what vehicle.
Defin a great install. I was going to bring my truck tomarrow to have one put in. I think I'll do it myself save the money.
sizes for the hose removal are 18mm and 20
Just realized you were making videos again. UA-cam had you at the bottom of my recommended list due to the hiatus a few years ago but I'm putting you back at the top! One of my favorite channels!
Thanks for the comment! We have a few new faces in the new shop. Good to hear from you again.
I was going to take my truck to a mechanic and after seeing this video I did it myself and save $1,000
Recently did this on my '96... after heating/beating/penetrating oil, slotted the pitman arm with a grinder to get it off... moving to "step 3" sooner would have saved time! Thanks for the video!
Supposed to use atf-4 in the power steering
Or Swepco... That's what PSC recommends
Time to upgrade the drag link and tie rod on that truck, the 08.5 steering linkage is much beefier and gets rid of death wobble... Good how to video :)
Patrick Tingley
Doing that to mine this weekend
Didn't get rid of my wobble. Nothing did until I did it all. The linkage, ball joints, shocks, gear box, steering shaft, pump and lines (the pump was toast to) I've dealt with that damn wobble for six years. Finally got fed up with chasing the problem. The problem isn't one thing, it's combination of parts. If one is worn, then it wears the new parts faster and that's why the wobble kept coming back.
@@maddawgnoll yup, most ppl naively think its one thing but its not, i was one of them. But all parts have to be very well worn in so they all can get in harmony and oscillate. Deathwobble gets annoying, having to avoid certain parts of the street or "better slow down just to XX mph"
Yes! Replace the linkage with the ‘updated’ ones makes a world of difference. Don’t forget Trac Bar bushings too!
Look up the EMF video about what actually happens during death wobble. It's interesting
Just changed the steering box on my wife's truck - using this video...
This video - fucking mint! 👌🏾
So the arm attached to the steering gear box doesn't need to be flush just tight as humanly possible. Also disconnected the steering shaft before turning the wheel back and fourth to bleed the lines. Unless you have a lift like these gents
I wonder what causes continuous bubbling in the reservoir...? Changed the pump along with the pulley when it started leaking, but it did bubble from the start and then the other day I had no power steering. Never sloppy, no noises, never stiff, just turned on tractor manual steering one day. Steering gearbox says my mechanic now. What next...? Scrap it I guess. 🙄
11:35 why does that intake manifold have a block off plate where the egr usted to go😂😂😂😂
it's an 18mm flare nut, use a flare nut wrench and it won't round off
Just waiting on the pitman arm removal tool which Amazon says I will get tomorrow then my the new PSC steering box goes in my 98 12V using this as a guide.
Odd question for you guys would a 4th gen box go into the 3rd gens?
yes they do chris
Yes they do, I went with a PSC box. MUCH better than the Red Head it replaced and totally worth the cost. Funny thing the PSC non hydro box is cheaper than OEM and much stronger.
Great "How to" video. Great job Ed.
Hi Lynne! Good to see you back on the Tube. Saw your last few vids and I hope you get a few more subs to reach your goal. Thanks for the comment!
@@edzgarage does the top of that arm you bolted on the sector shaft fit flush with the bottom of the sector box? Or is there space between the two where part of the spline is visible?
I just had a shop put a box on my dodge and noticed a gap exposed and could see the spindle or spline whatever it’s called.
Thanks for the advise on removing the wheel first.
So did it fix the loose steering?
When pulling the pit man arm dont hit the tool hit the side of the pitman arm should jolt lose
Awesome, no bullshit video. Any suggestions instead of using a pitman arm puller?
I turned wheel now my airbag and service electronic brake lights are on
Smashing job :-D, Zack made it look easy, that pitman arm and control rods look heavy duty, the weak spot i assume is the box, and perhaps the universal joint to the steering shaft/wheel.
It should have very little slop in the wheel now :-)
I hope there was at least one swear word off camera, it's just not a "propper repair" without one :-D.
Steering is crisp and tight. Those reman parts don't last tho, that's why they have "lifetime" warranty. They know us really well at the parts store :-) If there's even a hint of play it goes back for another one.
What attachment did you use on the cooler line? I can't get mine to thread in.
Great video!
Great job 👍
Missing the old ford tractor videos what happened
Just used ole 27 to plow the snow in the driveway yesterday. I have plans to do more tractor videos soon. Thanks for watching!
well done !
Thanks for the comment! Zach is a methodical mechanic, it's good to have him in the shop.
yeah he knows what he is doing
the pump fix the issue on the trans?
Yes, the pump did fix the torque converter locking issue in the trans.
My steerings off now 😓
Saaaaaaame
For sale sign on mine. Don't live in the US and the cost of maintenance is staggering. 🙄
Hi edz, Ive got the gear box changed by a garage. When i drove home I noticed the steering wheel is 15degr left, it is related to this operation? I asked them to align it and they refused,claiming that it is normal and should pay extra to fix it. Please advise.
old customs
Thats not normal the shop put the pitman arm on the wrong key.
Or they did not grind a new flat spot for the steering shaft sssembly locking bolt.
lol wierd way to replace a steering box.