REDTIGER HARDWIRE KIT (Install Prep, Connections & Fuse Taps Explained)

Поділитися
Вставка
  • Опубліковано 22 гру 2024

КОМЕНТАРІ • 241

  • @AlexAutoFun
    @AlexAutoFun  5 місяців тому +2

    Hi Everybody! If you have the USB C Hardwire Kit, here is my video for it ua-cam.com/video/_1cIkR3YB-8/v-deo.html Cheers!

  • @philkane4390
    @philkane4390 11 місяців тому +9

    Just bought a REDTIGER F7NP along with this HW kit for my Wrangler. Thanks for the vid, always great ones!

    • @AlexAutoFun
      @AlexAutoFun  11 місяців тому

      You're welcome Phil and congrats on your new F7NP dash cam! Cheers!

    • @americanpatriot8996
      @americanpatriot8996 4 місяці тому +1

      Just an FTI depending on what wrangler you have there are 6 accessory wires already there from factory. In the wrangler JL with the accessory switches they give you 6 wires in the engine bay and 6 wires under the foot well of the passenger side. So I installed my hardwire kit inside the vehicle and works like a charm. Just an fyi it makes it much easier.

    • @philkane4390
      @philkane4390 4 місяці тому

      @@americanpatriot8996 I have a 2024 Sport S. Man if I can install inside under the foot well that would be great! I'll check more on that.

  • @robtk3
    @robtk3 Рік тому +6

    Exactly what I was looking for. I was back and forth regarding the "Single Fuse" kit and the "Double Fuse (with taps)" kit. However, my Mazda has limited spots of BAT in the fuse box so I'm getting the Redtiger "Double 4 Fuse" kit. Your video was the deciding factor. Even though I already was looking at the product on Amazon, I'm going to buy it through your link (and, hopefully, you get some commission).
    Tu vídeos sempre exelcente!
    Gracias mano!

    • @AlexAutoFun
      @AlexAutoFun  Рік тому +1

      Thank you for supporting the channel Rob!

  • @Halfmoonphotography
    @Halfmoonphotography 10 місяців тому +2

    Thanks!

    • @AlexAutoFun
      @AlexAutoFun  10 місяців тому

      Thank you for supporting the channel EventHorizon!

  • @GuyzLikeMe
    @GuyzLikeMe Рік тому +6

    Thanks for a very clear explanation on how to install & how to fix the hurtles we might run into!

  • @lopeiaran3422
    @lopeiaran3422 Рік тому +12

    Your video was the best one on UA-cam that explained everything easily, thank you!

    • @AlexAutoFun
      @AlexAutoFun  Рік тому +1

      You're welcome and thank you Lopeil Aran!

  • @Halfmoonphotography
    @Halfmoonphotography 10 місяців тому +2

    I just bought rhis kit and red tiger F7PN i will be hard wiring in my 2020 subaru outback. Your video was extremely helpful.

    • @AlexAutoFun
      @AlexAutoFun  10 місяців тому +1

      Thanks EventHorizon, glad to hear it helped, Cheers!

  • @tschuler9923
    @tschuler9923 5 місяців тому +2

    Great info . And i love the "POP" when demonstrating pulling a fuse 😃

  • @user-DODOZ
    @user-DODOZ 2 роки тому +7

    They should have included the inline fuses in the wires, as the given fuses will only be for replacement of factory fitted fuses leaving the dashcam hardwire without any fuse as
    most people while installing hardwire don't bother about polarity of fuse taps and fuse sockets. And if some how they get the right polarity it will put double load on the single fuse as it will be providing power for both dashcam and default device.

    • @AlexAutoFun
      @AlexAutoFun  2 роки тому +2

      Hi DODO! correct, the kit unfortunately assumes that both ACC and BATT will be connected to unused spots on the car's fuse box (and also assumes the fuse size will be a Mini size) If the kit is connected to a fuse spot that is already occupied, the use of functional fuse taps shown at 4:22 is needed to ensure both the original fuse is retained along with the fuse for the hardwire kit. I keep telling dash cam manufacturers to improve this (AZdome does it ua-cam.com/video/FLcIM2MwAL8/v-deo.html and also Rove ua-cam.com/video/9Pq3UKQNrcU/v-deo.html with their awesome Ultimate hardwire kit) Hopefully one day they will listen! LOL Cheers Bud!

    • @khalilrazak6486
      @khalilrazak6486 2 роки тому

      Exactly, especially for how much it costs. There are third party ones which are cheaper and include the inline fuses but Redtiger doesn't recommend using third party hardwire kits, I wonder why!

    • @AlexAutoFun
      @AlexAutoFun  2 роки тому +1

      @@khalilrazak6486 Hi Khali! yeah that is the one major weakness I seen on dash cams, the dash cams themselves are fully loaded with features but their hardwire kits leave something to be desire. So far only Rove has he most complete hardwire kit I ever reviewed ua-cam.com/video/Ny-TvRnhTs4/v-deo.html but again as you mentioned, using the matching hardwire (made by the same brand as dash cam) is the what I also recommend to avoid issues both technical and warranty ones. Hopefully one day will we see more manufacturers create better kits like the Rove one. Cheers!

  • @pradeepb1277
    @pradeepb1277 9 місяців тому +1

    One of the best video i have seen in UA-cam

  • @cshajur
    @cshajur Рік тому +2

    Thank you for the clear and detailed exclamation on how to use this product. This information will be useful when we install our lower front bumper after-market fog lights on my 2021 Toyota Corolla LE Sedan.

  • @sxpress
    @sxpress 10 місяців тому +1

    Hi, nice video thank you.. there might actually be a jumper inside to change the voltage cut off?

    • @AlexAutoFun
      @AlexAutoFun  10 місяців тому +1

      You're welcome Sxpress! Ah I have not cracked this one open like the I did to this one ua-cam.com/video/RoiQ-Xvr09M/v-deo.html which was reversible since it has screws. But since the RedTiger kit is sealed, opening it would require prying apart (breaking into) the case. I don't believe there is a jumper like the Garmin one has but if I ever do break one open and confirm, I will update this comment for you. Cheers!

    • @sxpress
      @sxpress 10 місяців тому +1

      👍@@AlexAutoFun

  • @bazcharlie4680
    @bazcharlie4680 4 місяці тому

    Yr installation videos are no nonsense straight forward and informative greatly appreciated 👍 thankyou

    • @AlexAutoFun
      @AlexAutoFun  4 місяці тому

      You're welcome and thank you!

  • @piotrwiniarski3310
    @piotrwiniarski3310 Рік тому +1

    I have the hardwire kit from red tiger f7n dashcam. in my fuse box I have few empty slots but they have only 1 steel connect, apper or on the bottom. I was do so measure and I have the power when the engine ist turn of and when the key ist on. but the parkingmod don't want running. thank you for your help and great video and great job.

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Thank you Piotr! Ah yes here is my video showing how I find ACC and BATT on any vehicle ua-cam.com/video/K2iKXj82354/v-deo.html And here is my follow up video showing the rest of the install including some of the dangers involved with air bags when running the dash cam cables ua-cam.com/video/uZp95NbNlmM/v-deo.html And yes you can turn off Parking Mode in the settings menu if you don't need it. Here is my video showing how to use the dash cam ua-cam.com/video/K7qURDfoR7c/v-deo.html Cheers!

    • @piotrwiniarski3310
      @piotrwiniarski3310 Рік тому

      thank you for quick answer. but my question is or the hardwire kit can working with empty slot with single connector?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      You're welcome Poitr! Ah regarding your question, nope, most dash cams that require a 3 lead hardwire kit will usually need all 3 wires (ACC, BATT and GND) to be connected in order for the dash cam to work correctly. Here is is my other video ua-cam.com/video/Yky9_tTvwMc/v-deo.html where I explain how hardwire kits work and the different features to look for when buying one. Cheers! @@piotrwiniarski3310

    • @piotrwiniarski3310
      @piotrwiniarski3310 Рік тому

      I think my question was wrong. in a fuse box I have empty slots with single connector and I was plug in the hardwire kit w with 3 cables exactly like you show us. the real question is or can that working with single connector in empty slot in fuse box? because normal fuse has 2 connectors one ist at the bottom and one ist at the top, if I can say that...

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Piote! Correct, if there is a empty fuse slot available that is my preferred way of doing the connection, you can see an example of that install here ua-cam.com/video/uZp95NbNlmM/v-deo.html and here is my other video where I explained where fuse taps with two fuses or single fuse are needed ua-cam.com/video/Qzw9yUYN7zo/v-deo.html Cheers!

  • @christinartnd
    @christinartnd Рік тому +2

    I've watched all of your cameras for the red tiger F7NP - thank you fo being So detailed.
    however Im having LOTS of trouble installing it and I think I need to send back the entire camera - I have a brand new car - i've done all of the correct fuse checks and even had a dash cam fitter look at the car, but it seems that the redtiger hardware kit is turning the camera off once the inigition turns on, as it falls under 12v but then it doesn't turn the camera back on again.
    I tried an old nextbase camera that I also have, which only has a red hardwire cable and this works, turns on and stays on. but I cannot get the redtiger camera to work when hardwired. Do you have any suggestions?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому +1

      Hi Christina! That is very strange, specially if you had a installer verify the connections, maybe a bad hardwire kit? I would recommend contacting RedTiger for support, I'm sure they can walk you thru some troubleshooting steps. Hope this helps and please let us know what you find. Cheers!

  • @enfield7123
    @enfield7123 Рік тому +1

    Another good video 🧐 I got a E_ACE, reversing camera mirror cheap and cheerful.. but after a year decided to get another with all the fancy gadgets it was in my car for 3 months and it did my head in
    So now it's in the back of my garage and I put my cheap one back ..

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Thank you Enfield! Ah yes the E-Ace, I haven't tested that one yet but so far I had good results with the Veclesus version here ua-cam.com/video/67MZ7dpYd_g/v-deo.html may have to add a review for the E-ace later in the future. Cheers!

  • @RazoE
    @RazoE 2 роки тому +7

    Great video, even better mustache 👍🏻

    • @AlexAutoFun
      @AlexAutoFun  2 роки тому +1

      Thank you RazoE! I appreciate that bud!

  • @gtzrg
    @gtzrg Рік тому +2

    IM ASSUMING YOU DONT NEED THE HARDWIRE KIT IF YOU HAVE A CAR THAT PROVIDES FULL TIME POWER WHEN CAR NOT RUNNING?
    (OLDER CARS)

    • @AlexAutoFun
      @AlexAutoFun  Рік тому +2

      Hi Raul! The hardwire kit is only needed if you are looking to enable park monitor on your dash cam or if you do not want to tie up your cigarette lighter port with the charger. Hope this helps, Cheers!

  • @sempai940
    @sempai940 10 місяців тому

    Great video, however I cannot isolate a fuse to install the battery cable in a 2023 CRV Honda. Can you help?

    • @AlexAutoFun
      @AlexAutoFun  10 місяців тому

      Hi Angel! Here is my follow up video where I cover how I find ACC and BATT on any car ua-cam.com/video/K2iKXj82354/v-deo.html However I strongly recommend profession installation due to the dangers mentioned on that video if erroneously tapping a critical system of the vehicle and the dangers involved with air bags mentioned on this video ua-cam.com/video/uZp95NbNlmM/v-deo.html Cheers

  • @fisherbrown903
    @fisherbrown903 10 місяців тому +6

    For parking mode. Use

  • @cinemageek
    @cinemageek Рік тому +2

    Thank you so much for this video! This makes the whole process make so much sense! Thumbs up! 🎉

  • @darelord
    @darelord 6 місяців тому +1

    Is it ok if I attach kit's plug directly to fuse tap hole (the upper) without attach to fuse tap's cable? I think the hardwire kit plug already has fuse itself.

    • @AlexAutoFun
      @AlexAutoFun  6 місяців тому

      Hi Dare! I personally don't like to connect the hardwire molded fuse into a fuse tap, because I don't like how high the assembly gets when stacking the molded fuse from the hardwire kit into the fuse tap and then having to deal with cutting and shutting off the unused pigtail so it does not contact anything (here is the video where I show this ua-cam.com/video/wAad_JA7kz8/v-deo.html at the 9:55 mark for those wondering what that looks like) Cheers!

  • @X.8.f
    @X.8.f Рік тому +1

    Thanks so much for your videos. Just a question - I could not find a hard wire kit for my T27, can I use the kit of the T700 to power my T27?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      You're welcome Ali! Ah yes the T27 hardwire is readily available from Amazon or from RedTiger, I put links to both sources in the video description. Hope this helps, Cheers!

  • @jonnylee8538
    @jonnylee8538 Рік тому +1

    Hi, are the fuses soldered with the hardwire kit working ones or just as a plug? If they are, how many Ampere are they?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому +1

      Hi Jonny! Correct, they are standard 15 AMP (blue fuses) Cheers!

    • @jonnylee8538
      @jonnylee8538 Рік тому

      @@AlexAutoFun Thanks, I thought they were 15A.

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      @jonnylee8538 Hi Johnny! Correction, you are right, I typed too fast lol they are 15A. Cheers!

  • @servicecar7916
    @servicecar7916 10 місяців тому

    Hello my friend, thank you for the video, but upon installation the video appears 24 hours a day quickly. Is there an option for that?

    • @AlexAutoFun
      @AlexAutoFun  10 місяців тому +1

      Hi Service! Sounds like you have enabled "Time Lapse" if you want regular video recording, I would recommend turning that function off. Cheers!

  • @izzymoney85
    @izzymoney85 Рік тому +2

    Thanks a bunch for this helpful tutorial for this Hard wire kit keep up the great work man

  • @LyRiCss718
    @LyRiCss718 Місяць тому

    Good morning question at video mark 3:29. I am taping cigarette lighter adapter. It has a red and yellow wire. Can i tap them together and connect together? I am connecting a carpuride dash. I just want it to have power.When the vehicle is on, it doesn't need to have power when it vehicles off.

    • @AlexAutoFun
      @AlexAutoFun  Місяць тому +1

      Hi L! Ah remember this kit is meant for RedTiger dash cams, it is not mean for other aftermarket products. I would recommend contacting Carpuride for hardwire information. Cheers!

  • @abhinavg3514
    @abhinavg3514 5 місяців тому

    So you cannot place the ACC terminal which you're supposed to put in an empty slot in the fuse box into the fuse tap, you're supposed to cut the wire, attach it to the fuse tap wire, buy and place another similar fuse and then use it?

    • @AlexAutoFun
      @AlexAutoFun  5 місяців тому

      Hi A! Fuse taps are only used in some cases, here is my video where I explain this in more detail ua-cam.com/video/Qzw9yUYN7zo/v-deo.html Cheers!

  • @pauljohnsonyola370
    @pauljohnsonyola370 24 дні тому

    Can i also use the OBD wire for red tiger for parking also??

    • @AlexAutoFun
      @AlexAutoFun  24 дні тому

      Hi P! I have not tested the Redtiger OBD adapter so I can't say exactly how it will behave but here is my video for OBD power adapters ua-cam.com/video/YEklm9V6xYE/v-deo.html Cheers!

  • @shelikesjustthat431
    @shelikesjustthat431 Рік тому

    im on my daughters profile by the looks but ill ask anyway, just wondering why or if it would work by cutting the twin fuse link wire short and insulating it then plugging in the already fused wire from the dashcam and the fuse that came from the fuse box into the twin link then plugging it back into the fuse box slot to save time? I think it will work and will be checking it out tomorrow but probably wont cut it short just incase the dashcam fuse blows I can then join and get a fuse. ok ok saying it like that kinda makes me think why stuff around. thanks Max :)

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi! Fuse taps are only required when tapping into a fuse spot that already has a fuse in it. Here is my other video where I explain when fuse taps are needed ua-cam.com/video/Qzw9yUYN7zo/v-deo.html And here is my other video where I explain hardwire kits and their differences to look for when buying one ua-cam.com/video/Yky9_tTvwMc/v-deo.html Cheers!

  • @wolvoman1
    @wolvoman1 6 місяців тому +1

    Thanks for an informative video, however i could never understand branding it as '' RedTiger'' ?

    • @AlexAutoFun
      @AlexAutoFun  6 місяців тому

      You're welcome Mike! Ah yeah I see so many brand names (sometimes using terms related to the product and sometimes totally unrelated) and I always wonder the same LOL There was a couple ones that were a little extreme too, there was one that almost sounded like an expletive (not when read only when pronounced) and I had another that sounded like a different term that what the brand intended (again, not when read only when pronounced) and there are some I have not even figure out how to pronounce them since they are made up words. Cheers!

  • @Unplugged704
    @Unplugged704 10 місяців тому

    Question- If I hardwire for power all the time, why is there a need to connect to the ACC?

    • @AlexAutoFun
      @AlexAutoFun  10 місяців тому

      Hi Unplugged! Ah good question, ACC provides the signal that the car is On or Off which makes the dash cam turn On or Off for you with the car (and also trigger parking monitoring if enabled on the dash cam). The 3rd wire (BAT) is used to maintain power to the dash cam while the car off. And here is my follow up video where I explain how hardwire kits work and their different features to look for when shopping for one ua-cam.com/video/Yky9_tTvwMc/v-deo.html Cheers!

  • @hsushssbwj
    @hsushssbwj Рік тому

    what is maintainance for the hard wire? i actually afraid low volt not cranking on standard liquid old car battery

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Clovax! The hardwire kit is sealed and does not require maintenance. Here is is my other video ua-cam.com/video/Yky9_tTvwMc/v-deo.html where I explain how the hardwire kits work and the different features to look for when buying one (including the low voltage cut off). Cheers!

  • @vichetkim-p1s
    @vichetkim-p1s 10 місяців тому +1

    I just bought exact same kits for my Subaru forester

  • @javiersalas7670
    @javiersalas7670 Рік тому

    So will it not function or record once the battery voltage gets below 11.8?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Javier! Correct, the low voltage cut off is meant to stop the hardwire kit from powering the dash cam when the battery voltage reaches the cut off point to reduce the possibility of draining your car's battery. Cheers!

    • @javiersalas7670
      @javiersalas7670 Рік тому

      @@AlexAutoFun Thats not good I bought one for parking security....mainly for that reason only

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Javier! Most name brand hardwire kits have a low voltage cut off to reduce the possibility of draining your car's battery and leaving you stranded. There are a few basic hardwire kits out there (cheaper) that do not have that function and will stay on all the time at the expense of the car's battery being drained. So while it is possible to do so I personally do not recommend it. Most healthy batteries will stay above the cut off point so I personally always use hardwire kits with low voltage protection. Cheers! @@javiersalas7670

  • @zendrith5018
    @zendrith5018 11 місяців тому

    I really want to get the RedTiger hardwire kit to use with my RedTiger camera. my only issue is that the version of the camera i have is Micro USB and I cannot find that version of the kit online anymore. Would it be worth it to buy their USB-C kit and splice the Micro USB from their car charger onto it, getting a USB-C to Micro USB adapter, or getting an entirely different kit be the best move? I think cutting the USB-C head off the new one and soldering a Micro USB head from the car charger i have from them would be the more fun move (the bottom of my car charger from them also shattered and i cant find the pieces anymore so its dead at this point to me)

    • @AlexAutoFun
      @AlexAutoFun  11 місяців тому

      Hi Zendrith! Ah I got the same version too! lol yes the Micro-USB hardwire kit has been replaced with the USB-C. I normally recommend sticking to the matching hardwire kit for your dah cam but in this case I can see why an alternative may be needed, here is one that may work amzn.to/3NBqLcD but yes if you are experienced with electronics, swapping out the connector on the new USB-C one to a Micro-USB is definitely possible (and yes it could be fun depending on if you enjoy working and soldering small electronic components like I do LOL). Cheers!

  • @KDR195
    @KDR195 Рік тому +1

    Hi - I’m going to be installing red tiger into a f15 x5 and the fuse that I’ll be removing and adding to a fuse tap are 5amps each for acc and batt. What fuse amp does the red tiger require for acc and batt? I dont have any space in my fuse box. Thanks in advance!

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Kelvin! Ah yes the fuse for the hardwire kit I used, is of the same value as what came with the kit. In this case as you can see in the video the kit came with a blue fuse (15A), so I used a 15A fuse on the functional fuse tap. Cheers!

    • @KDR195
      @KDR195 Рік тому +1

      @@AlexAutoFun thanks for replying!!! Do you think instead of a 15A fuse red tiger cam would be ok with a 5A fuse?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      @@KDR195 Yeah I had other viewers used a lower rated AMP fuse (so it can pop earlier) However just remember that deviating from the included AMP spec may impact warranty if something goes wrong in the future since we are deviating from the factory kit. Hope this helps, Cheers!

  • @CJL-Land
    @CJL-Land Рік тому

    Hi. Thank you for your very helpful and informative video. Finally realised I was needing a Fuse Tap to correctly install & use my RedTiger Dashcam & Hardwore Kit.
    Are the soldered Fuses on the hardwire kit 15A for both the ACC and BATT wires?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому +1

      Hi Chris! correct, the molded on fuses are soldered to the kit (underneath the molding) Here is my follow up video on how I replace this molded fuses with actual functional fuse taps ua-cam.com/video/Qzw9yUYN7zo/v-deo.html Cheers!

  • @swapnilpx
    @swapnilpx Рік тому

    Can the Redtiger F7N hardwire kit be used with Wolfbox G840H dashcam ?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi! I do not recommend mixing up hardwire kits, here is the hardwire kit for the G840H amzn.to/3DylNIB Cheers!

  • @user-DODOZ
    @user-DODOZ 2 роки тому +2

    I think wolfbox and redtiger are part of same parent company, both have similar type of hardware and app.

    • @AlexAutoFun
      @AlexAutoFun  2 роки тому +1

      Hi DODO! That's correct, RedTiger is a Wolfbox brand 🙂

    • @user-DODOZ
      @user-DODOZ 2 роки тому +1

      @@AlexAutoFun Thanks for making such detailed informative videos, we appreciate your hardwork🤗

    • @AlexAutoFun
      @AlexAutoFun  2 роки тому

      You're welcome 𝑫𝑶𝑫𝑶! Glad to hear they helped 😊

  • @karenmoore4315
    @karenmoore4315 Рік тому

    What if your hardwire kit only has the red and black but DOES have the shut/off device for the voltage? Will it still work in parking mode?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Karen! This will depend on your dash cam, most require their matching hardwire kit and using a different kit may not work correctly. Cheers!

  • @flonga1
    @flonga1 Рік тому

    I have a 2008 4Runner, should I get the double fuse or single fuse?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi! The need for a functional fuse tap will depend if there are empty fuse spaces (both ACC and BATT) on the vehicle, here is my video where I explain when functional taps are needed ua-cam.com/video/Qzw9yUYN7zo/v-deo.html and here is video showing the actual installation ua-cam.com/video/uZp95NbNlmM/v-deo.html Cheers!

    • @flonga1
      @flonga1 Рік тому +1

      @@AlexAutoFun THANK YOU!!!!

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      @@flonga1 You're welcome!

  • @opawchicago2602
    @opawchicago2602 Рік тому

    Hi,this works with any dashcam brand?thanks

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Opaw! While it may be possible to use a different hardwire kit on a dash cam, I usually recommend sticking to the matching hard wire for the dash cam (brand matching) to ensure that there are no functional issues or issues with warranty coverage. Here is my video which covers hardwire kits and their differences in more detail ua-cam.com/video/Yky9_tTvwMc/v-deo.html Cheers!

  • @paulroberts6697
    @paulroberts6697 Рік тому

    Hi can you tell me what is the fuse rating in amps of the links fitted to the hard wire kit for the G900. Mine are coloured blue. Blue fuses are normally rated at 15 amps . I want to fit my red and yellow wires with in line fuse holders as I wish to tap into another circuit on my Landrover. What size fuses should I fit? 15 amp seems a rather high value.

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Paul! Correct, the fuses that come with the G900 hardwire kit are blue (15A). And here is my hardwire install video ua-cam.com/video/uZp95NbNlmM/v-deo.html Cheers!

    • @paulroberts6697
      @paulroberts6697 Рік тому +1

      Many thanks for your quick reply. Your videos are excellent.😊

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      @@paulroberts6697 You're welcome and thank you Paul!

  • @danev6972
    @danev6972 9 місяців тому

    I have the REDTIGER F7N 4K Dual Dash Cam. Amazon has a single fuse and double 4 fuse option. What is the difference. Thx.

    • @AlexAutoFun
      @AlexAutoFun  9 місяців тому +1

      Hi Danev! The single fuse one includes molded fuse as shown on the video. The Double Fuse, has replaceable ends (fuse taps) which are needed in some of the cases described on the video. And here is my follow up video that covers when fuse taps are needed in more detail ua-cam.com/video/Qzw9yUYN7zo/v-deo.html Cheers!

  • @claudeb.3473
    @claudeb.3473 Рік тому +2

    Thank you, this was very educational. The sound effects are great, too. 😀

  • @pierroalino
    @pierroalino Рік тому

    Hi mate. Thank you for the video. May I ask a question about the setting please?
    I have a fun since yesterday and the hardWire kit. I juste found the food spot to plug the red and yellow wires but I get a message saying use the acc wire kit when I try to use the parking mode .... ..
    And when I torn the ignition key all works perfect but when I turn it off it say ACC off then off
    Do you have any idea on what I could do to fix this please?
    Thanks regards

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi pierroalino! I would have the installer check all the connections (ACC, BATT & GND) to confirm nothing has come loose and that they connected to the correct locations for ACC and BATT (I seen cases where park mode is not enabled if ACC and BATT are reversed or connected to the incorrect locations that does not provide power at the correct time for both ACC and BATT) Hope this helps, Cheers!

    • @pierroalino
      @pierroalino Рік тому +1

      @@AlexAutoFun hi I contacted redtiger and they helped me figure out how to solve my problem. I just had to replugged the red wire into a another fuse slot and now it s all working fine. Thanks for you answer have a good day

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      @@pierroalino You're welcome and glad to hear it's working now. Cheers!

    • @haych9803
      @haych9803 Рік тому

      If you want the dash cam to function only when ignition is on , and turn off when ignition is off (to save car battery) can you just use the accessory fuse wire and ignore the battery wire ?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      @@haych9803 Hi Haych! The dash cam will turn off when the ignition is off and turn on when the car is On when connected correctly with the 3 lead hardwire kit (If additionally you don't need parking monitoring, most dash cams will let you turn it off in the settings menu) Hope this helps, Cheers!

  • @federicoeduardolopezdiaz2703

    Hi do you think I can connect my dash cam Hotwire on a Honda accord sport 2017?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Federico! Yes most dash cams support a hardwire kit. Here is my hardwire video ua-cam.com/video/uZp95NbNlmM/v-deo.html the techniques shown on that video can be applied to any vehicle including the Honda Accord. Cheers!

  • @rcharger007
    @rcharger007 Рік тому

    Ever had an instance where the yellow B+ when connected starts up the camera, but then the camera immediately loses power? If the car is started through the ACC the camera stays on with no problem. Having this issue currently with a Subaru Ascent 2022

    • @AlexAutoFun
      @AlexAutoFun  Рік тому +1

      Hi Ray! I would have the installer check the install, checking that the car fuse spot still has power at the correct time (both for ACC and BATT) I seen cases where the car will turn off power to particular systems (specially in ECO mode, hybrid and EV vehicles) in to maximize fuel efficiency. Here is the video for how I find and test for ACC and BATT ua-cam.com/video/K2iKXj82354/v-deo.html If the both fuse spots for ACC and BATT have power at the correct time, I would also recommend contacting RedTiger for support, maybe just a bad hardwire kit? they may just swap it for you, or guide you thru some troubleshooting steps. Hope this helps, and please let us know what you find. Cheers!

    • @rcharger007
      @rcharger007 Рік тому +1

      @@AlexAutoFun spoke with support and the issue turned out to be a bad hardware kit. New kit is working fine! Camera came right on and goes in to parking mode without issues

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      @@rcharger007 Awesome! Thank you for keeping us posted too! 🍻

  • @jrshields683
    @jrshields683 Рік тому

    I need a video that tells me where to get a hardwire kit for a Low Profile fusebox (2021 Lexus NX).

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi JR! Here are the low profile fuse taps amzn.to/3yZiJkN and here is my hardwire install video ua-cam.com/video/uZp95NbNlmM/v-deo.html Cheers!

  • @vinesco5270
    @vinesco5270 2 роки тому

    Does the amperage of the fuse on the fuse tap have to match the amperage of the fuse you took out?
    My kit came with a 15A fuse on the fuse tap, but the fuse im taking out is 7.5A. What should I do?

    • @AlexAutoFun
      @AlexAutoFun  2 роки тому +1

      Hi Vin! ah yes I have a detailed video covering this ua-cam.com/video/K2iKXj82354/v-deo.html Hope this helps, Cheers!

  • @fisherbrown903
    @fisherbrown903 10 місяців тому

    Can i wire b+ direct into battery terminal +. Not the acc wire

    • @AlexAutoFun
      @AlexAutoFun  10 місяців тому +1

      Hi Fisher! ACC and BATT need to be connected to their correct locations (ACC and BATT are separate functions, here is my video where I cover this in more detail ua-cam.com/video/K2iKXj82354/v-deo.html ) in order for parking monitoring to work correctly. If ACC or BATT is connected to a source of power that does not provide ACC or BATT power at the right time, the dash cam may not work, parking mode may not work or the dash cam could stay On all the time. Cheers!

    • @fisherbrown903
      @fisherbrown903 10 місяців тому

      @@AlexAutoFunvery hard to access for camry toyota. Under the steering wheel

    • @AlexAutoFun
      @AlexAutoFun  10 місяців тому +1

      @fisherbrown903 Hi Fisher! I don't doubt it. That is one of the reasons I recommend professional installation. In addition to the time invested in trying to learn the process for a single install, some installs are also physically demanding, I lost count of how many times I had to twist myself into a pretzel to reach the work area. There's also sharp areas of the trim of the car or the sheet metal itself, so it's usual that my hands are cut left to right LOL. I gotten good at it (like all installers do after hundreds of installs), but this experience won't be developed on a single install. Cheers!

    • @fisherbrown903
      @fisherbrown903 10 місяців тому

      @@AlexAutoFun yes. Very hard for toyota. Under steering hard to access

  • @albertomedina193
    @albertomedina193 7 місяців тому

    Can I use this kit for a headunit (carplay screen) ?

    • @AlexAutoFun
      @AlexAutoFun  7 місяців тому +1

      Hi Alberto! This is kit is specific for the dash cam models listed by Wolfbox (link to the kit in the video description). I do not recommend using it differently. Cheers!

    • @albertomedina193
      @albertomedina193 7 місяців тому

      @@AlexAutoFun Thank you for your fast response. You just earned another subscriber. If you have any recommendations for a hardwire kit that I can use for a carpuride headunit, I would greatly appreciate it.

    • @AlexAutoFun
      @AlexAutoFun  7 місяців тому

      ​@@albertomedina193 You're welcome and thanks for supporting the channel Alberto! Ah unfortunately, Carpuride does not have a hardwire kit, they typically use 12VDC, so there is no step down regulator in their power plug assuming your Carpuride system is like this one ua-cam.com/video/oHlf0MmguWk/v-deo.html You can see how the power input is labeled 12V so what installers do in those cases where the customer requires a hardwire connection is either cut the cigarette lighter plug and tap the system directly to the car (with fused connections) or they install a generic cable with the same DC barrel plug which again is connected to the car's power via a fused connection. Cheers!

    • @albertomedina193
      @albertomedina193 7 місяців тому

      @AlexAutoFun you are the Man. Thank you!!!

    • @AlexAutoFun
      @AlexAutoFun  7 місяців тому

      You're welcome Bud!

  • @hardikbatish7966
    @hardikbatish7966 4 місяці тому

    New redtiger app doesnt have GTRIGGER OPTION FOR parking feature. Any advise on that? And also if we leave screen on with hardwire. Does it make much difference

    • @AlexAutoFun
      @AlexAutoFun  4 місяці тому

      Hi H! Parking mode features vary from dash cam to dash cam. The App will let you select impact detection for park monitoring if the dash cam supports it and if it's hardwire correctly. I actually have a video on this coming up, stay tuned. Cheers!

  • @lawrencewood-norman6479
    @lawrencewood-norman6479 4 місяці тому

    @AlexAutoFun Can I use this kit for another Dashcam mirror that uses a Type C port, or is it just for Red Tiger?

    • @AlexAutoFun
      @AlexAutoFun  4 місяці тому

      Hi L! While I may be possible to use a different hardwire kit on a dash cam, I usually recommend sticking to the matching hardwire kit for the dash cam (specified by the brand) to ensure that there are no functional issues or issues with warranty coverage. Here is my follow up video ua-cam.com/video/Yky9_tTvwMc/v-deo.html where I explain how hardwire kits work and the different features to look for. Cheers!

  • @skudlugs
    @skudlugs Рік тому

    what about using obd2 adaptor for power?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Shaun! Correct, the OBD2 adapter is able to power some dash cams, here is my full video for it ua-cam.com/video/YEklm9V6xYE/v-deo.html Hope this helps, Cheers!

  • @samuelflores8961
    @samuelflores8961 6 місяців тому

    will this protect my cars battery and alternator?

    • @AlexAutoFun
      @AlexAutoFun  6 місяців тому

      Hi Samuel! Typically hardwire kits do not affect alternators (but I would recommend checking with your mechanic to confirm the effects of adding aftermarket equipment to your vehicle). But yes as explained in the video, it does have low voltage protection to reduce the possibility of draining your car's battery. Cheers!

  • @jaredjason8
    @jaredjason8 Рік тому

    hello i have a hardwire kit that is 20awg but my fuse taps that i need to connect too the wire is 16awg. what can i do or can i just connect them?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Jared, here is are some IDC connectors with the range you are looking for amzn.to/44OkIYl Cheers!

  • @gabostln3119
    @gabostln3119 3 місяці тому

    If I connect the hareware kit, do I nned to connect the other wire to the start the camera or is not nevcesary?

    • @AlexAutoFun
      @AlexAutoFun  3 місяці тому

      Hi G! Most dash cams that require a 3 lead hardwire kit will usually need all 3 wires to be connected in order for the dash cam to work correctly. What I recommend when someone does not need park monitoring, is just to turn it off in the settings menu (most dash cams will let you turn off this feature). Cheers!

  • @andersonammelo
    @andersonammelo 9 місяців тому

    Very well explained video. Thank you!

    • @AlexAutoFun
      @AlexAutoFun  9 місяців тому

      You're welcome and thank you Anderson!

  • @carlomemmolo3337
    @carlomemmolo3337 Рік тому

    are you near newhampshire,i have problems where phone wont exept codes or icon scanned

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Carlos! Not sure which dash cam you are using but remember the T27 and T700 do not support connecting to your phone. You can also contact RedTiger for support, they may be able to walk you thru some troubleshooting steps. Cheers!

  • @mmagen14
    @mmagen14 Рік тому

    Can please do dash cam Hotwire on 2020 Corolla?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Megan! Here is my hardwire video ua-cam.com/video/uZp95NbNlmM/v-deo.html Cheers!

  • @americanpatriot8996
    @americanpatriot8996 4 місяці тому +5

    This hard wire kits are a bad design because of that fuse ever blows your screwed and will have to use a fuse tap anyway. But I had to do mine a little different anyway. I have a wrangler JL and in the wrangler there are 6 fused wire taps on the inside cab under my glove box so I used the 10 amp and 15 amp battery and acc connections. I cut off the fuse taps on the kit and spliced in my own fuse taps. And all the wiring is on the inside of my cab and I didn’t have to run it far and didn’t have to go thru the firewall. Only issue is there is a lot of slack I had to roll up and hide behind and under my glove box. No big deal it all works and is fuse protected. But now it’s protected by 2 fuses because the factory wires are already fuse protected. Just extra protection but works as designed. The original issue I had with this was the hardwire kit doesn’t allow you to remove the fuse if it goes bad.

    • @AlexAutoFun
      @AlexAutoFun  4 місяці тому

      Hi A! Ah yes Redtiger, has since upgraded their kits to this new design ua-cam.com/video/_1cIkR3YB-8/v-deo.html Cheers!

  • @yellowgreen2378
    @yellowgreen2378 6 місяців тому

    Does it drain the battery too much?

    • @AlexAutoFun
      @AlexAutoFun  6 місяців тому

      Hi Yellow! Ah good question, that will depend on the car's battery, size, age, health condition and state of charge. In addition to that you also want to take in consideration any parasitic draw from other items on the vehicle that use power when the car is off. This is specially common on newer vehicles. For example I have an older Jeep that can sits for months a time with little to no battery draw, then I have a 2017 car that will almost completely drain my battery in a few weeks if the car is not used (and that car does not have any aftermarket devices connected to it). Here is the battery tester I use ua-cam.com/video/kCNrfa8RUKU/v-deo.html if you want to test your battery for capacity and health, it can also perform a parasitic draw test if needed. I do carry one of this on long trips ua-cam.com/video/5eoewaav43A/v-deo.html just in case but again I think my case is a little more extreme since most people only run 1 hardwire kit at a time and I run several kits on my car. Cheers!

  • @andytooturnt
    @andytooturnt 7 місяців тому

    how do you know what number/size the new fuse has to be?

    • @AlexAutoFun
      @AlexAutoFun  7 місяців тому

      Hi Andy! Notice they are using blue fuses which means they are 15A (if the molding is removed the fuses, the fuses are also marked with 15A). Cheers!

  • @Lance-b2l
    @Lance-b2l Рік тому +1

    👍👍💯 thank you very well explained

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      You're welcome and thank you Lance!

  • @BLINDEYE
    @BLINDEYE 11 місяців тому +1

    such a well explained video thank you so much for the help

    • @AlexAutoFun
      @AlexAutoFun  11 місяців тому

      You're welcome and thank you!

  • @mr.boniato6402
    @mr.boniato6402 Рік тому

    How come when I connect only the ACC cable in the cigarette lighter fuse slot without connecting the BA+, the camera won't turn on when the car is on.. I have to ALSO connect the BA+ along with the ACC wire.. why is that? Why can't I just plug the acc wire and only use it on acc mode?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Mr. Boniato! most dash cams that use a 3 lead hardwire kit require all 3 leads to be connected in order to function (ACC, BAT & GND). Hope this helps, Cheers!

    • @mr.boniato6402
      @mr.boniato6402 Рік тому

      @@AlexAutoFun Thank you..when using the cigarette lighter as acc, do I need to have two fuses, one for the kit and one for the lighter, or is the one from the kit enough to power the lighter and the camara?

  • @piciux2323
    @piciux2323 8 місяців тому

    i had my redtiger camera hardwired by an electician for me and after almost 2 days of using the camera 24/7 i wonder if it`s normal for the actual dash cam to be warm/hot and if is there any chance of catching fire or i shouldn`t be worried about it ?

    • @AlexAutoFun
      @AlexAutoFun  8 місяців тому +1

      Hi Catalin! Dash cams normally run warm to hot (and very hot if running it in 4K). And while I had not had any of them catch on fire yet, if you are looking to reduce their temperature here are some suggestions. Reduce resolution (lower resolutions produce less heat), reduce bit rate (some dash cams will let you change it) and finally enable screen saver (screen time out) which will turn of the display after a period of time but will continue recording (the screen itself generates heat). Cheers!

    • @piciux2323
      @piciux2323 8 місяців тому +1

      @@AlexAutoFun thank you, I just did all that, feels a bit better, still warm tho' I'm just worried because I just had a new car and installed this dash cam and the hardwire kit and I'm worried about it being always warm/hot and what this can do in the long term.

    • @AlexAutoFun
      @AlexAutoFun  8 місяців тому +1

      @piciux2323 You're welcome! It would also be a good idea to have your installer check the install. I seen cases where something was incorrectly connected or the wrong hardwire it was used (or a defective hardwire was installed) etc. Cheers!

  • @turdferguson1521
    @turdferguson1521 Рік тому

    What do you do if the fuse box has no empty spots ?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Turd! Here you go ua-cam.com/video/Qzw9yUYN7zo/v-deo.html Cheers!

  • @billhattori3034
    @billhattori3034 7 місяців тому +1

    Great instruction and commentary. More willing to attempt this myself now. Thanks!

  • @nikmills
    @nikmills 3 місяці тому +1

    Very Helpful.

  • @bentenxl
    @bentenxl 8 місяців тому

    I wonder if this works with the 70mai dash cam..

    • @AlexAutoFun
      @AlexAutoFun  8 місяців тому

      Hi Ben! While I may be possible to use a different power adapter on a dash cam, I usually recommend sticking to the matching power adapter for the dash cam (brand matching) to ensure that there are no functional issues or issues with warranty coverage. Here is my follow up video ua-cam.com/video/Yky9_tTvwMc/v-deo.html where I explain how hardwire kits work and the different features to look for. Cheers!

    • @bentenxl
      @bentenxl 8 місяців тому

      @@AlexAutoFun Thank you bro! i actually am switching to a wolfbox dash cam! thanks to one of your vids btw :D!

    • @AlexAutoFun
      @AlexAutoFun  8 місяців тому

      @@bentenxl You're welcome! 🍻

  • @vipulpatel2544
    @vipulpatel2544 Рік тому

    How can i install redtiger hardwired kit in toyota sienna 2023 model?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Vipul! Here is my hardwire installation video ua-cam.com/video/uZp95NbNlmM/v-deo.html Cheers!

  • @jimmynguyener24
    @jimmynguyener24 Рік тому +1

    You are very detailed 👌 🤝😌

  • @chloropheneramine6593
    @chloropheneramine6593 8 місяців тому +1

    Superb explanation

  • @sachinbohra007
    @sachinbohra007 4 місяці тому

    will using hardwire void the warranty??

    • @AlexAutoFun
      @AlexAutoFun  4 місяці тому

      Hi S! Are you referring to the warranty of the dash cam or the vehicles warranty?

    • @sachinbohra007
      @sachinbohra007 4 місяці тому

      @@AlexAutoFun vehicle warranty

    • @AlexAutoFun
      @AlexAutoFun  4 місяці тому +1

      Hi S! Ah, that's a good question (often a debated one). You would want to check your State's law. In my State supposedly the law prevents a Dealer from denying warranty if someone added something to their car or worked on their own car as long as whatever was added or the work that was done was not the cause of the failure. So let's say you put window tint on your car and your transmission fails. It would probably be difficult for the dealer to deny it because the tint or the tint install did not likely affect the transmission. But as simple as that sounds, there are horror stories of dealers not honoring warranty if they see a modification claiming it is what led to the failure. Some owners even had to take them to court or complain directly to the manufacturer (since dealers are typically independently owned) to get their warranty honored. Cheers!

  • @dariocurseri6736
    @dariocurseri6736 2 роки тому

    Buongiorno ho acquistato la dashcam t 27 con il kit per il monitoraggio del parcheggio 24 Ore su 24.
    Ho fatto installare il tutto all'elettrauto.
    Il monitoraggio del parcheggio è comunque possibile decidere se attivarlo o disattivarlo in modo che non registri?
    Se si in che modo?
    Grazie

    • @AlexAutoFun
      @AlexAutoFun  2 роки тому +1

      Hi Dario! correct if the hardwire kit was installed correctly there will be a new option in the menu where you can choose park monitoring using the G-Sensor or Time Lapse. I do have a video explaining how to setup the parking mode on the T27 next week. Stay tuned for that one, Cheers!

    • @dariocurseri6736
      @dariocurseri6736 2 роки тому

      Perfetto grazie mille!

  • @jonathanshim282
    @jonathanshim282 Рік тому

    If I don't want the constant power (parking mode) enabled, do I simply not plug in the constant power fuse? or does that need to get plugged in regardless?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Jonathan! Most dash cams that require a 3 lead hardwire kit will usually need all 3 wires to be connected in order for the dash cam to work correctly. What I recommend when someone does not need park monitoring, is just to turn it off in the settings menu (most dash cams will let you turn off this feature). Cheers!

    • @Unplugged704
      @Unplugged704 10 місяців тому

      Like me, I just want to run camera when I’m in the car-driving.
      I feel I can just use the cigarette lighter.
      What is the pro of hardwiring if I just use the camera when driving?

    • @AlexAutoFun
      @AlexAutoFun  10 місяців тому +1

      Hi Unplugged! Typically the only advantages of hardwiring is that it frees up your cigarette lighter port and it can also enable parking mode. Cheers!@@Unplugged704

    • @Unplugged704
      @Unplugged704 10 місяців тому +1

      @@AlexAutoFun Thank you!

    • @AlexAutoFun
      @AlexAutoFun  10 місяців тому

      You're welcome!@@Unplugged704

  • @ronleon62
    @ronleon62 7 місяців тому

    They now sell kits with several differ fuse taps included.

    • @AlexAutoFun
      @AlexAutoFun  7 місяців тому

      Hi Ron! Correct, the kits have been updated, most now come with fuse taps (links to the kits in the video description) Cheers!

  • @vincentlee2460
    @vincentlee2460 8 місяців тому

    The 2 fuses value into the piggy peg wire must add up to the original single fuse value. Otherwise you are increasing the ampere allowed and might cause a fire.

    • @AlexAutoFun
      @AlexAutoFun  8 місяців тому +1

      Hi Vincent! Ah remember a functional fuse tap creates 2 separate independent circuits (each one with a different amp rating partially determined by fuses that are loaded into the each fuse slot in the fuse tap, the car's internal wiring and current load on the circuit to be tapped) The fuse removed from the car goes in the fuse tap bottom slot and the second fuse (top fuse) is for the hardwire kit. So they are each independent of each other, each one driving it's own load. Here is another video ua-cam.com/video/Qzw9yUYN7zo/v-deo.html where I explain how fuse taps work in more detail, Cheers!

    • @vincentlee2460
      @vincentlee2460 8 місяців тому +1

      @@AlexAutoFun i was wrong. The 12 volt is split and the fuses are not in series. I just confirmed with a DMM and the same wire.with 2 fuses

    • @AlexAutoFun
      @AlexAutoFun  8 місяців тому +1

      @@vincentlee2460 That is a great way of explain it, I actually have a video on the works covering the internals of them because as simple as this little guys are, sometimes it helps to see the inside of something to understand it, but I like your idea of the DMM demonstration. Cheers Vincent!

  • @davidserban3747
    @davidserban3747 Рік тому

    Him mate yu sayd to live în description link woth the fuse plug ant test plug

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi David! Correct, I put links in the description to the hardwire kit and fuse taps if needed. Hope this helps, Cheers!

  • @abbottgirl82
    @abbottgirl82 Рік тому

    Hello - I've just had my unit installed at an audio shop and he told me that I need to read my manual when I go home because when trying to access the Parking Mode, he gets an error stating, "please connect the acc power kit" which is what he's done so what do I do now?

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Zurai! I like to start by saying (no disrespect to the shop that installed it) but any shop that tells a customer to go home and read to manual to figure it out, man that kind of customer service upsets me and I would definitely not go back to that place. That being said, I would have the installer confirm all connections to confirm they are connected to the correct locations for ACC and BATT (I seen cases where the connections for ACC and BATT are reversed or connected to the incorrect locations that do not provide power at the correct time for both ACC and BATT leading to the kit not working correctly). I also seen cases where a shop joined both ACC and BATT together to save time causing the issue you are describing. In rare cases you may also have a defective hardwire kit (or incorrect hardwire kit installed by the shop) which again your installer can confirm for you. Lastly you can also contact RedTiger for tech support, they may be able to walk you thru some troubleshooting steps. Hope this helps and I hope the shop comes thru and helps you my friend, Cheers!

  • @AllThruChrist
    @AllThruChrist Рік тому +1

    Very great.

  • @secondmindfilms7962
    @secondmindfilms7962 6 місяців тому

    Where’s the other video link?

    • @AlexAutoFun
      @AlexAutoFun  6 місяців тому +1

      Hi Second! Here you go ua-cam.com/video/uZp95NbNlmM/v-deo.html and there are more related videos I placed links to the in the video description. Cheers!

    • @secondmindfilms7962
      @secondmindfilms7962 6 місяців тому +1

      @@AlexAutoFun Thank you!

    • @AlexAutoFun
      @AlexAutoFun  6 місяців тому

      @@secondmindfilms7962 You're welcome!

  • @Leinsterbaby
    @Leinsterbaby Рік тому

    Noticed you don't have anything on Kenwood cameras, they have a funny hardwire kit, with just 1 fuse connector + ground :D

    • @AlexAutoFun
      @AlexAutoFun  Рік тому

      Hi Goose! Ah yes the 2 lead hardwire kits, yeah those are not as common but yes install is same but instead of connecting 3 wires only 2 wires are connected (refer to the instructions of the kit to determine the function of the 2 wires, most use GND and ACC and some use GND and BATT). Here is my hardwire video where I cover 2 lead and 3 lead hardwire kits ua-cam.com/video/Yky9_tTvwMc/v-deo.html and here is my follow up video showing the hardwire install process ua-cam.com/video/K2iKXj82354/v-deo.html Cheers!

    • @Leinsterbaby
      @Leinsterbaby Рік тому

      @@AlexAutoFun Cheers for responding. The reason I asked, because normally, there is 3 wires, ground, constant and ignition on only, this enables the one with ignition on to work when you drive, and constant to work when there is a parking mode. I am trying to wrap my head around, how parking mode will work in that setup, when car is off :D
      Also, would you reccomend Kenwood cameras the 501 and 601? They have nice sets with those kits included and rear cams.

    • @AlexAutoFun
      @AlexAutoFun  Рік тому +1

      @@Leinsterbaby Ah yes, I would recommend to check the instructions for the kit, as mentioned earlier some two lead hardwire kits use ACC (switched ignition power) and GND and some other kits use BATT (constant battery power) and GND. It just depends on the kit and how it was designed to function. Usually on ACC and GND kits the dash cam will not have parking mode (unless it's equipped with a battery) and on kits with BATT and GND the dash cam will either stay on to record when the car is off or will enter parking mode after period of time. Ah regarding the 501 and 601, unfortunately I have tested any of their dash cams but I will see if I can add to the list of dash cams to review, stay tuned and Cheers!

    • @Leinsterbaby
      @Leinsterbaby Рік тому +1

      @@AlexAutoFun Cheers! My dad says, if you don't understand it, leave it. So prime day is upon us, and I am going with a Vantrue x4s or a redtiger, depending which will be cheaper! :) They got both 3 wire kits. Thank yo for your hard work.

    • @AlexAutoFun
      @AlexAutoFun  Рік тому +1

      Haha that is a good saying, haven't heard it before but it's so true! 🍻

  • @Lydiadragonbourne
    @Lydiadragonbourne 7 місяців тому

    Thank you!

    • @AlexAutoFun
      @AlexAutoFun  7 місяців тому

      You're welcome Lydia, Cheers!

  • @latunyabarriere537
    @latunyabarriere537 9 місяців тому

    Redtiger gives the hardware parking kit for free!

    • @AlexAutoFun
      @AlexAutoFun  9 місяців тому

      Hi LaTunya! Nice! I have heard that they do that in some cases when you contact them, glad to hear they took care of you. Cheers!

  • @juniorcruz51
    @juniorcruz51 Місяць тому +1

    Ahora uno en español

    • @AlexAutoFun
      @AlexAutoFun  Місяць тому +1

      Hola J! Ah si e pensado en traducirlos pero el año pasado hice una encuesta en el Canal para ver si hay interes en videos en Espanol pero muy poca gente contesto "Si". A lo mejor es buen tiempo para hacer la encuesta otra vez haber si hay mas interes esta vez. Por el momento si te vas en los adjustes del video (se ve como un engrane) lo puedes ver con subtitulos en Español. Saludos!

    • @juniorcruz51
      @juniorcruz51 Місяць тому +1

      @@AlexAutoFun si deberías hacer de nuevo la encuesta, yo entiendo inglés, pero hay mucha gente que no sabe inglés y tus videos son de mucha ayuda, me gusta como explicas y si haces unos cuantos videos en español sería genial! 👍🏼

  • @mvirdi2333
    @mvirdi2333 2 роки тому +2

    ❤❤🙏🙏U.K.

  • @simonramirez243
    @simonramirez243 6 місяців тому

    I don’t think you can put a fuse on a fuse..

    • @AlexAutoFun
      @AlexAutoFun  6 місяців тому

      Hi Simon! Correct, it's not possible to put a fuse on a fuse. However fusetaps can be used to place 2 fuses into 1 fuse spot. Here is another video ua-cam.com/video/Qzw9yUYN7zo/v-deo.html where I explain how fuse taps work in more detail, Cheers!