Im glad they are doing another update to clean up 1.15 to dial it in finally. I know I watched a live show where Dilek told me there wouldn’t be anymore updates for the legend based on a question I had asked.
@@2010stoof Dilek said they had room to do more just there were a lot of users who were upset about all the updates even when they were for improvements. That was why she said they were going to stop updating. Then she saw a video that IffySignals did during a comparison and she and the engineers jumped on the V1.16 update seeing that it was needed.
@@EdwardG13So should I take mine back to 1.13? It served me fine but saw 1.15 and went for it however haven't had much time to test it but 1.13 was doing well for me. Better to set back to 1.13 until 1.16 is finished and 1.17 is released?
@@2010stoof I would just hold off until the update is ready. However if you feel more comfortable with1.13 then it’s truly up to you. I’m doing fine with 1.15. You could also go back to 1.14 if you are considering going back a version. I’m going to just wait until the update is ready and roll on with it.
I hope it’s quieter. I can’t run my sensitivity over 23 in any mode and any coil since the last update. Noise cancellation doesn’t help either. And I even went to my spot that is 2 miles from the closest power lines and it didn’t help.
Not sure what all ppl are complaining about with the 1.15. I liked it, and Ive found the BM very usefull at the beach with saltwater. I usually switch around from beach wet to beastmode and back again, BM really make targets stand out with its sound settings.
Put a ring of gold on them with iron tongs, they will see the iron tongs and not even feel the gold. So much for the esteemed Nokta legend. Detector bucket.
I've had my legend for a while I bought new with v 1.13 but I have not done any updates to it , my question is do I need to update the previous update (beast mode) before updating to the latest version (v1.17) ? Hope you can help Phil.
Look forward to your beach video. I've had issues with 1.15 in salt water. It's been very noisy even after factory reset to stock settings beach wet all metal. It hits on corals and gives video even if drop down sensitivity 18 .V1.09 is stable and does not do that. On the dry v1.15 is very good but sensitive to power lines and wifi nearbye. I don't get these issues with 1.09
After i updated on the double score from 1.0 to 1.2 beta the pinpoint is not working well. My impression is that in 1.0 was better. Deep Target i stil need to test it in all modes. 😚
@@calabashdiggeradventures this was my first update. Do you think I need the silicon USB driver for updates or have they figured out the USB driver issue now?
Hi calabash , sorry to jump in on your comments section but it's in relation to the nokta triple score, I bought one last week and updated it out of the box with the new 1.2 beta version. I live over the pond in England and a few of use are having issues with this update.to be brief the machine seems to be over sensitised, our ground is not mineralised and we mostly run our machines in 0 ground balance , the problem is I can't get the sensitivity over 8 before it's starts chattering like hell. I like to hunt in all metal in field m1 or m2 but the machine won't have it, even after iv noise cancelled and ground balanced, iv even tried ground tracking but nothing helps. Iv emailed nokta but a forum member told me nokta won't reply to emails, they want videos only. I wonder is there any chance you could help us out with this issue, cheers!
Yes straight after the update. After the first outing I did a second restart but still no joy, I thought it could be a faulty coil but my friends is doing the same thing!
Please Please check out the tripple score problems with the sensitivity.its now ready a problem with more and more people and after the 1.2 update its getting worse please tackle this problem.and i am talking on land m1 m2 multi and single freq
@@calabashdiggeradventures thanks yes first of all programs m1 m2 are way to sensitive if the coil is touching something then straight away u het fala signals specially on farm field with stabbles.but even on grass it gives false signals.u need to put the sensitivity back to 8 or less if u want to have a stable coil.and that is in multi frequency and single freq. M3 and relic mode are more stable .and after the beta update its getting worse the machine goes crazy everywhere any field .yes dus is really a huge problem and on fb more and more people facing this issue.so if u want to look at it it would be great thanks
Im glad they are doing another update to clean up 1.15 to dial it in finally. I know I watched a live show where Dilek told me there wouldn’t be anymore updates for the legend based on a question I had asked.
@@EdwardG13 that's sad that no more updates. Unless they think they've maxed the tech inside
@@2010stoof Dilek said they had room to do more just there were a lot of users who were upset about all the updates even when they were for improvements. That was why she said they were going to stop updating. Then she saw a video that IffySignals did during a comparison and she and the engineers jumped on the V1.16 update seeing that it was needed.
@@EdwardG13So should I take mine back to 1.13? It served me fine but saw 1.15 and went for it however haven't had much time to test it but 1.13 was doing well for me.
Better to set back to 1.13 until 1.16 is finished and 1.17 is released?
@@2010stoof I would just hold off until the update is ready. However if you feel more comfortable with1.13 then it’s truly up to you. I’m doing fine with 1.15. You could also go back to 1.14 if you are considering going back a version. I’m going to just wait until the update is ready and roll on with it.
I hope it’s quieter. I can’t run my sensitivity over 23 in any mode and any coil since the last update. Noise cancellation doesn’t help either. And I even went to my spot that is 2 miles from the closest power lines and it didn’t help.
hmmmm...
i bougth mine last week and its quiet over 23.
Same here there is a issue with some legends that to erratic I sold mine not sure what happend@@calabashdiggeradventures
Hey CBD, thanks for keeping us up to date on the updates.
No problem 👍
Thanks Calabash!
Im still on the 1.13 version guess ill just wait for the 1.16!!!! Thanks sir!!!
Not sure what all ppl are complaining about with the 1.15. I liked it, and Ive found the BM very usefull at the beach with saltwater. I usually switch around from beach wet to beastmode and back again, BM really make targets stand out with its sound settings.
Well done Nokta & CD
The Legend is on Hit !!!
Do you know when this be available? Can't wait!
I do not know exactly..
Put a ring of gold on them with iron tongs, they will see the iron tongs and not even feel the gold. So much for the esteemed Nokta legend. Detector bucket.
Looking good Calabash
How does it work with all the emi.Around your house.
It handles it pretty good..
It’s looking promising
I've had my legend for a while I bought new with v 1.13 but I have not done any updates to it , my question is do I need to update the previous update (beast mode) before updating to the latest version (v1.17) ? Hope you can help Phil.
No..just update it from what I understand
..
Thanks for vid.
You bet
Nice video, appreciate everything you do🍺
I appreciate that
Well done. Thank you. 🙏🙏🙏
Thank you too!
Look forward to your beach video. I've had issues with 1.15 in salt water. It's been very noisy even after factory reset to stock settings beach wet all metal. It hits on corals and gives video even if drop down sensitivity 18 .V1.09 is stable and does not do that. On the dry v1.15 is very good but sensitive to power lines and wifi nearbye. I don't get these issues with 1.09
Thanks!
did the double score have any of those weird bugs like the triple did?
After i updated on the double score from 1.0 to 1.2 beta the pinpoint is not working well. My impression is that in 1.0 was better. Deep Target i stil need to test it in all modes. 😚
Have not tested the Double..
I just went to 1.15. but havent gotten to use it. 1.13 was doing well for me. Should i just revert back to 1.13 until 1.17 is out?
Dont know...
@@calabashdiggeradventures this was my first update. Do you think I need the silicon USB driver for updates or have they figured out the USB driver issue now?
I do not know that either...I updated from my Mac multiple times with no issues.
Hi calabash , sorry to jump in on your comments section but it's in relation to the nokta triple score, I bought one last week and updated it out of the box with the new 1.2 beta version. I live over the pond in England and a few of use are having issues with this update.to be brief the machine seems to be over sensitised, our ground is not mineralised and we mostly run our machines in 0 ground balance , the problem is I can't get the sensitivity over 8 before it's starts chattering like hell.
I like to hunt in all metal in field m1 or m2 but the machine won't have it, even after iv noise cancelled and ground balanced, iv even tried ground tracking but nothing helps.
Iv emailed nokta but a forum member told me nokta won't reply to emails, they want videos only. I wonder is there any chance you could help us out with this issue, cheers!
I will look at this ...
@@calabashdiggeradventures thank you!
Do you factory reset after update?
Yes straight after the update. After the first outing I did a second restart but still no joy, I thought it could be a faulty coil but my friends is doing the same thing!
I tried it on two different versions I got and can not replicate it....YET will test some more Monday ...
How do i get that update?
Not released yet..
1.16? Это новое? Или вы перепутали с 1.15?
1.16 is the beta test version. It will be released as 1.17 to the public
Nokta site does not have version 1.16 only 1.15
Not released yet..
1.15?
1.16 beta..
the title says 1.16 beta
Any word on When is the vortex being officialy released ?
Your guess is good as mine ...
Please Please check out the tripple score problems with the sensitivity.its now ready a problem with more and more people and after the 1.2 update its getting worse please tackle this problem.and i am talking on land m1 m2 multi and single freq
I will look at it...What is the problem?
@@calabashdiggeradventures thanks yes first of all programs m1 m2 are way to sensitive if the coil is touching something then straight away u het fala signals specially on farm field with stabbles.but even on grass it gives false signals.u need to put the sensitivity back to 8 or less if u want to have a stable coil.and that is in multi frequency and single freq. M3 and relic mode are more stable .and after the beta update its getting worse the machine goes crazy everywhere any field .yes dus is really a huge problem and on fb more and more people facing this issue.so if u want to look at it it would be great thanks
Thanks!
That POS machine will not stop chattering¬!!!!!
All machines chatter on that side of my house..