Just warms my heart to hear you guys busting your back to fix this old truck and send it to Haiti. They need it with the building of the canal, for access to water. God only knows, not too many people care about Haiti and the struggles of its people. Good on you guys !
Another idea , when you cant see what you need to take off parts , use a good flashlight and your cell phone to take a video , in hard to get to places , then you can rerun the video and hopefully see the problem Great videos keep on keeping on ....it's great to see those old dinosaurs come to life
Thanks for another great video. It was super interesting. Congratulations to Hank and Wiley for getting the old Mack to run. You both did a lot of work but got it to run. Yea!!!!!!!!!!! You both did great. Thanks. The Iowa Farm Boy. Steve.
Great to see some use in this old equipment even if it's used somewhere else...we need to change our mindset from just toss and scrap everything to a more rebuild and repurpose. I don't know about you but cost of equipment and trucks is through the roof ..and it's half as reliable as the old stuff....great content as always fellers😎🚜🛠️🧑🔧🛻⛽🇺🇸
The large lever is the throttle the smaller shorter lever above it is the fuel shut off that should be connected to a cable that goes to a knob on the dash not sure why so much money was spent on a fuel pump on an old truck. I sold a lot of Factory reman pedigreed fuel pumps like that one when I work at the Mack Dealership in the 80s
The diesel filter is at bottom that is water drain petcock from Parking diesel filter. Right there on your hand was the Bosch Cummins diesel fuel filter head fitting so it take twist it on filter with capacity one quart.
On a few old inline pumps I've had the cam follower stick in the bore of injection pump. Take the lines off use a pin punch bump motor if it's not moving give em a tap until they cycle up and down smoothly
Im so glad you finall pulled up your truck beside the job atbhand feet away usually your about 30 yds away carrying heavy batteries ....remember work smart not hard and hardly working is fun
The service truck has enough room, they could get a 12 volt Charger and run a power line and ground off the truck batteries or get a large Power inverter, hard wire the charger so they can throw starter batteries on it and let them charge while they are in route to where they are going,
Can you bring it up the top dead center and make sure it's number one and not number 6 in the crankshaft spends probably about 30 times before the timing marks will wind up again
There a hole for a drill bit on the fly wheel, about a 13m or eq , then on the water pump and other timed bits has the same thing a hole when the mark on the flywheel lines up will all the drill bits in place you are at TDC on 1 put a spanner or socket with a tube and move it by hand , first disconete your battery , like that no one can turn the engine over by accident , The flywheel where the starter is, the timing marks are on the other flywheel where the radiator is , its very simple to do , good luck guys.
When I was 12 i got a fordson tractor going flat head removed that had a fire and oil in bores hit pistons with a round fence post. Had only hand tools No batteries as it had a magneto and a crank handle
Yeah we are going to do this a few times. We have a few pieces of equipment that we did 4-5 videos on, so I thought it would be cool, to compile them all together so you can see the whole process in one video instead pieces of it. I got one more scheduled in December and probably do another one in Jan.
Well give us a heads-up that is what it is hank I was all excited to see a nice long one tbh wish you would have put it this way from the start much more entertaining and easier to keep up with than waiting for the next one
Hi guys my name is Mike I live in Michigan and I enjoy watching you videos I wasvjust thing it would be greT if for ever thing you get started you and wally should sign it somewhere on the engine saying something like (hank and wally was here )or just you john Hancock would be great write back tell me what you think
This is a Mack in somewhat year 1990 plus it has hours of driving odometer. The turbo must rotate plain your recommendation air pneumatic and blow thru turbo. It should loose spin easily. Use 2 heavy batteries and hook up to 24 volt engine starter. And diesel is okay and J doubt it so use gasoline for cold start. And brake is bad use your big puller and pusher to grab the brake drums very press it out of it. Then do you have the pusher puller on 21 inch wheel. Thank you very much.
I was very interested in that huge chain saw set iup that you picked up and wonder if you ever got it set up as i have never seen anything as big as that and wondered how effective it was. I do not recall seeing you pick up the bar itself when you loaded it up on the low loader?
One of the best video 📹 seen you two should be go on stage well hank you remind me of my late father u largh at your own joke's lol 😆 amazing you got onother pump definitely not a mack macanic plenty in Australia and newzealand thanks again
Another choice besides Perkins or Donaldson or WIX P 551103 spin on diesel fuel filter and it need the head that Mark Model Truck R with the head aluminum venter
i always wonder where the old polished tank milk trucks go .there has to be old ones out there but you never see them abandoned heck i rember as a kid watching tri axles in 70s going past farm beautiful trucks but where did they go?
I see that you have a hard time with gaskets this works for any gaskets that you can think of if it has both holes a piece of sewing string not the nylon type regular cotton sewing string it will hold it place will not affect the seal
my uncle years ago worked for bruckners mack in amarillo tx.he sent me a jacket.been told mack never sent anyone jackets even if you bought a new mack i been offered 300 for it but i caint do that theres one ole cig burn in it oops
When Hank put the open wrench heads, on the ground time mark 48.16. How are the heads used? I've seen them but never got to see them being used. We love you and Wiley.
Is that 2 valve plus 2 stroke exhaust port and Most of Mack diesel engine is 4 stroke but the piston is 6 inch long dish top piston drop forged. The piston not flat top and neither domed top. They would sleeve the piston and kill the piston head and it bore thru their piston for 8 cylinder E Model Engine Mack and Bosch turbocharger on cool blower side.
Glow is glow plug similar to spark plug very 6000 rpm not engine revolution just tester revolution repeat sparks arc many time per second. The exhaust port and intake type 2 stroke is right on the side of the engine block counter flow of inline 6 big engine.Include s dry pump turbo.
Wow talk about making a career out of changing out an injection pump lol😅 well you guys are doing a great job keep up the good work it’s a good thing you are getting paid by the hour 😊
▶Watch 3 pieces of equipment here: ua-cam.com/video/SPA6B2Iqgwk/v-deo.html
💰SCHOLARSHIP LINK: bold.org/funds/hamiltonville-farm-scholarship-fund/
That big nuts don't have to come on that's the only
There's got to be another night somewhere y'all just got to
Just warms my heart to hear you guys busting your back to fix this old truck and send it to Haiti. They need it with the building of the canal, for access to water. God only knows, not too many people care about Haiti and the struggles of its people.
Good on you guys !
Three hours! I need to call in sick tomorrow so I can watch this!
Hank and Wily: The Movie. 🎥🎬 😂😂😂 Nominated for 3 Oscars! Excellent job guys!! Keep up the great work!!
Guys at first I thought I was watch a new type of comedy show instead of two good ole boys working on a truck. 😂😂❤❤❤
I'm glad I'm not the only person that can take something apart and then have trouble reassembling it!!!
I love these videos. The old trucks and machinery they come across is Kool to see. Hank and Wily are so funny!
That’s really awesome Hank and Wiley on getting the Mack semi truck running again
Thanks fellas I have to admit I fast forwarded to the 3 part of this series just to see newest one , but I will go back and rewatch it tomorrow.
It's all good. Thanks for watching what you can.
Willy you got Hank sweating good on you, amazing to see wonder boy get greasy, awesome video and finally a long one start to finish
Good Morning Gentleman, it is great to see you again today and I hope you are having a fantastic day 😊❤ !
Hey guys I’ve been watching you for a few months. I think you’re doing a fine job on the will it start videos. Having fun is the name of the game.
Thank you
Glad you got it going guys
Always makes my day complete when you post a video, Thanks Hank
Thanks
Another idea , when you cant see what you need to take off parts , use a good flashlight and your cell phone to take a video , in hard to get to places , then you can rerun the video and hopefully see the problem
Great videos keep on keeping on ....it's great to see those old dinosaurs come to life
Hank you and Wiley should be able to get it to run 🏃♀️ you have a good day working on the truck 🛻
You guys are something else!! Watching this video where you are taking a fuel pump off of a old truck!!
Great, a 3 HOUR ONE. I love the long videos. Thanks for taking the out of your day to gilm your content, but make you don't be Wiley.
Thanks for another great video. It was super interesting.
Congratulations to Hank and Wiley for getting the old Mack to run. You both did a lot of work but got it to run. Yea!!!!!!!!!!!
You both did great. Thanks.
The Iowa Farm Boy. Steve.
🎉❤ you guys do great work 💪... thanks for the video 👍📸📸 guys.... JJ...😊
Great to see some use in this old equipment even if it's used somewhere else...we need to change our mindset from just toss and scrap everything to a more rebuild and repurpose. I don't know about you but cost of equipment and trucks is through the roof ..and it's half as reliable as the old stuff....great content as always fellers😎🚜🛠️🧑🔧🛻⛽🇺🇸
love what you guys are doing keep it up
Thanks fpr the great content.
Looking forward to over 3 hours of Hank and Wiley.
Always fun watching you two. Not sure about the DAD jokes tho😅.
The large lever is the throttle the smaller shorter lever above it is the fuel shut off that should be connected to a cable that goes to a knob on the dash not sure why so much money was spent on a fuel pump on an old truck. I sold a lot of Factory reman pedigreed fuel pumps like that one when I work at the Mack Dealership in the 80s
I watched this one for 45 minutes before i realized I've already seen it.
Wednesday the 15th at 7:14 am my time here in AZ 😊 !
if y'all have a harbor freight store in Florida they sell a magnetic tray to put the loose nuts and bolts in so you won't lose them
The diesel filter is at bottom that is water drain petcock from Parking diesel filter. Right there on your hand was the Bosch Cummins diesel fuel filter head fitting so it take twist it on filter with capacity one quart.
On a few old inline pumps I've had the cam follower stick in the bore of injection pump. Take the lines off use a pin punch bump motor if it's not moving give em a tap until they cycle up and down smoothly
Im so glad you finall pulled up your truck beside the job atbhand feet away usually your about 30 yds away carrying heavy batteries ....remember work smart not hard and hardly working is fun
Great job runs like a champ ready to go bye bye.
Pom❤qwqhwg9763bh
Phpomhah
I haven't seen one of them injection pumps in a long time
Hanks fav word,,, Counter Clockwise😂😂😂
I wondered if there would be a way to put an extra alternator on your service truck to charge the batteries you use to start the machines?
The service truck has enough room, they could get a 12 volt Charger and run a power line and ground off the truck batteries or get a large Power inverter, hard wire the charger so they can throw starter batteries on it and let them charge while they are in route to where they are going,
Hanlk I have a saying I put on a t-shirt... Your only a master when you do it wrong and it still works.
Cool.truck
Can you bring it up the top dead center and make sure it's number one and not number 6 in the crankshaft spends probably about 30 times before the timing marks will wind up again
There a hole for a drill bit on the fly wheel, about a 13m or eq , then on the water pump and other timed bits has the same thing a hole when the mark on the flywheel lines up will all the drill bits in place you are at TDC on 1 put a spanner or socket with a tube and move it by hand , first disconete your battery , like that no one can turn the engine over by accident , The flywheel where the starter is, the timing marks are on the other flywheel where the radiator is , its very simple to do , good luck guys.
When I was 12 i got a fordson tractor going flat head removed that had a fire and oil in bores hit pistons with a round fence post. Had only hand tools No batteries as it had a magneto and a crank handle
Stanley Wonder bar all flat strong stock and its end is nail puller crow neck 1 foot to 12 1/2 inch max length L letter 3 inch into pry line.
That was a good one love see them drive
I’ll say one thing this pump has kicked your butt every inch of the way but you’re persistent and got it done 😊
tremendo mecánicos esos dos maestro y el humor especial para trabajar desde Argentina mí saludos y vamos qué los vamos con los yankee ❤
Old Content just replayed...dam
Yeah we are going to do this a few times. We have a few pieces of equipment that we did 4-5 videos on, so I thought it would be cool, to compile them all together so you can see the whole process in one video instead pieces of it. I got one more scheduled in December and probably do another one in Jan.
ok y'all...u know ill keep watchin..God Bless
Well give us a heads-up that is what it is hank I was all excited to see a nice long one tbh wish you would have put it this way from the start much more entertaining and easier to keep up with than waiting for the next one
the pump will only go on 1 way it will be obvious when it is removed wich remove mountging bolts pick rear up to clear comp and remove same
Good video how much was it to rebuild that pump
My sockets are 30mm deep set 32, 34mm and 1 1/2 inches shallow socket 12 point 3/4 inch drive and Snap On professional ASE tools.
U guys do the best u can 👍
I enjoy watching you and especially the OLD MAN HAHA
The background sounds like y’all must still be near Elba or Kinston
The only problem I see is you guys need a cap with a Mack Bulldog on it.stay safe.
Great job again!
You guys Crack me up love the show
My dad needs physical therapy......that dam ole truck in the driveway is my therapy 😂
Hi guys my name is Mike I live in Michigan and I enjoy watching you videos I wasvjust thing it would be greT if for ever thing you get started you and wally should sign it somewhere on the engine saying something like (hank and wally was here )or just you john Hancock would be great write back tell me what you think
This is a Mack in somewhat year 1990 plus it has hours of driving odometer. The turbo must rotate plain your recommendation air pneumatic and blow thru turbo. It should loose spin easily. Use 2 heavy batteries and hook up to 24 volt engine starter. And diesel is okay and J doubt it so use gasoline for cold start. And brake is bad use your big puller and pusher to grab the brake drums very press it out of it. Then do you have the pusher puller on 21 inch wheel. Thank you very much.
How much did that rebuilt pump cost you ? 😊
Another idea , when you cant see what you need to take off parts , use a good flashlight and your cell phone to take a video , i like.
Good job Guys.
I was very interested in that huge chain saw set iup that you picked up and wonder if you ever got it set up as i have never seen anything as big as that and wondered how effective it was.
I do not recall seeing you pick up the bar itself when you loaded it up on the low loader?
One of the best video 📹 seen you two should be go on stage well hank you remind me of my late father u largh at your own joke's lol 😆 amazing you got onother pump definitely not a mack macanic plenty in Australia and newzealand thanks again
Another choice besides Perkins or Donaldson or WIX P 551103 spin on diesel fuel filter and it need the head that Mark Model Truck R with the head aluminum venter
Love Wileys T-shirt this things Ma!king Oil !!
Hank what is on front the cam shape with a bolt in it?
You really didn't need to take it off the springs where stuck up needed to be knocked down onto the cam followers lubed and worked up and down
Take acetone and transmission fluid mix them together in a spray bottle
i always wonder where the old polished tank milk trucks go .there has to be old ones out there but you never see them abandoned heck i rember as a kid watching tri axles in 70s going past farm beautiful trucks but where did they go?
👍. I've watched at least 20 hf videos in the past week. Glad I found y'all. I'ma professional wish operator but identify as a farmer
lol 👍
I bet it changes timing hank?
Yeah boy she’s a running. And away we go to the grocery store. Lots of laughs.
theres a gear inside the timing cover you have to take a nut with a bent washer if i remember correctly
its quite a job to get to it if my memory is right been a long time
I see that you have a hard time with gaskets this works for any gaskets that you can think of if it has both holes a piece of sewing string not the nylon type regular cotton sewing string it will hold it place will not affect the seal
my uncle years ago worked for bruckners mack in amarillo tx.he sent me a jacket.been told mack never sent anyone jackets even if you bought a new mack i been offered 300 for it but i caint do that theres one ole cig burn in it oops
Hanks t-shirt lol!!!!
Thais guys y’all rock it
That poor mack not worth the price of the injection pump 😮
When Hank put the open wrench heads, on the ground time mark 48.16. How are the heads used? I've seen them but never got to see them being used. We love you and Wiley.
Does the guy still have the 530 construction King below your house where you went look for parts for Black Betty
So what's with the No and Yes ballcaps?
good job..
I thought this was a new video it says posted a day ago I watched this video probably a week ago at least
Is that 2 valve plus 2 stroke exhaust port and Most of Mack diesel engine is 4 stroke but the piston is 6 inch long dish top piston drop forged. The piston not flat top and neither domed top. They would sleeve the piston and kill the piston head and it bore thru their piston for 8 cylinder E Model Engine Mack and Bosch turbocharger on cool blower side.
Glow is glow plug similar to spark plug very 6000 rpm not engine revolution just tester revolution repeat sparks arc many time per second.
The exhaust port and intake type 2 stroke is right on the side of the engine block counter flow of inline 6 big engine.Include s dry pump turbo.
Use multimeter and please check and read 24 or 25 volts minimal and jumper battery costs too much and way hard like 100 amp battery charger to find.
Hank me and wilie want to know why you turned your back on the old 7.3 Ford
Hank & Wally why not take a before & after picture!
What's the meaning of the ball cap? Wiley's has YES on it and yours has a NO.
🚜
Hey I have a Farmall superA that was my grandpa tractor and I'm trying to get running again
I watch your show everyday a couple episodes and just love the show, I will also check out willies show. I can even handle the jokes Ha Ha
How do you get them to the destination
One simple question do ues 2 know what ues are doing there
Who doesn't like Mexican food can you get good tamales down there
You need to add a vice on your truck
Before TDC
Wow talk about making a career out of changing out an injection pump lol😅 well you guys are doing a great job keep up the good work it’s a good thing you are getting paid by the hour 😊
😊🙂Марат👍. Машина. маск. 🛠️😇🤗Хорошо. да.
i had a 1984 mack
Old man did they say there was only one ever made
What Happened To The Drivers Side Door On The Semi.
What are ues trying to do there