Power Commander Installation tutorial. Yamaha R6. 2014 Yzf-r6. Dynojet Power Commander
Вставка
- Опубліковано 13 вер 2024
- Power commander Installation Tutorial. Yamaha r6. 2014 Yzf-r6.
Video of how to install the power commander on a 2014 Yamaha R6, Most bikes will be similar, but the instructions that came with the PCV were usable. I will let you know what I think of it after I have ridden for a bit with it installed. Thanks for watching, Like, COmment, SUB!
No one shows the two plugs, why
Awesome video,just straight installment ✌🏼️
eLeVeN34 thanks for watching!
helpful
+Rev Bomb
Thanks for Watching I have been subd to ur shit for a while! Cool to have input from a fellow vlogger.
***** now worries man a helpful (that i will never do either) but a tripod for installs is great if you want to go that route
Thanks man helped me
Decent video, now how do you go about actually tuning the power commander, do you need to take that out every time to plug it into a computer or how does it work?
P Squared you have to have a laptop. or a computer outside lol. it comes with a long cable. you install it then with it on the bike you load the maps using the dynojet software
When you plug in the optimizer, is the old wire obsolete?
old video I know, but does anybody know what to do with the optimizer after? looks like he just deleted the o2 basically. where does the o2 side of the plug go into? or does it just hang out and not used?
since i installed it the beeping sound from the first few seconds afteer you turn on the ignition doesn`t go away. Any ideas?
What happened if I don't put the o2 sensor ? I still have the catalytic converter on with the sensor on it it only need it when you get rid of those right? Is the check engine light going to turn on?
Andres Garabito if you keep the stock cat you shouldn't get a check light
What's the Part# for the PC5?
good video..very helpful!!
thanks for watching!
+KIKO_R6
thanks for watching and commenting! Please share and sub!
Did you hook up your spedometer and temp gage wires?
Kendrick Campbell it's in the harness. It all works correctly as far as I can tell
whats the power source for the power commander? i installed it but there not light or power in the power commander?
See 8:40 wire #5 you have to put the small wire in line with the blue wire on your small ecu plug
Dego Motovlogs I have the yamaha r6 2017
Should be similar but maybe not exactly the same.
What exactly does this power commander do? more power?
+Juan Perez
Makes the bike run Better (according to dynojet and internet) lol especially if you plan on heavily modifying the exhaust or other performance parts. Makes fuel/air ratio correct after mods and for different climates. Thanks for watching and commenting!
hmmm.. It doesn't work. when I put my bike on, the power commander Light "power" is not shining.
Roentje86 must have them in the wrong spot try and double check the wiring make sure you have the right colors going to the right spot otherwise contact Dynojet or take it to a shop they were watching sorry it didn't work out
how do u fix it.... i have the same problem i dont have the light power on
did you delete the 02 sensor?
nope. on mine the o2 is on the big muffler box not the slip on pipe. but even if you have a midpipe the sensor should still be on it.
Why was the o2 optimizer required ?
man that shit looks confusing ass fuck lol
LilRuger347 it's really not that bad just try and follow the instructions if you're that worried about it is probably better to get it to a shop which is not a bad idea anyway since they should I know it to get the best tune thanks for watching
Dego Motovlogs dude I wind up putting the PCV and the block off plates on by myself today lmao