Removing Car dent with Boiling water and a plunger! DIY
Вставка
- Опубліковано 24 вер 2024
- Showing how to remove a dent with boiling water and a plunger. Remember that not all dents are the same and some are not going to come out this way! Mine still had a little deep one at the end of the day. Doesn’t hurt to try though!
Hey guys if y’all have the chance to subscribe to my girls page that’ll be dope. She just started a vlog channel so tell all your girls to visit her channel and share. Appreciate y’all --> Priscilla Analiese 🔥💪🏽
❤️❤️❤️😘
That last name tho... 🤪
Hey what's up Jose? I know this is old and I'm late to the party, Lol .... But I came across your video because I have a dent to remove. Man don't pay any attention to the people in the comments trying to clown for likes. Just let it roll off your back and keep it moving 💯 At least you're Trying, Showing and Sharing content 👍🏾🙏🏾 The most 90% of them do is surf for videos that they can jump on the bandwagon with other people and criticize because they have nothing to do. Make more videos and keep going man. Subbed today.
Did this work ..??
"be careful not to burn yourself" says the guy in shorts, tank top and sliders 😂
Every way he can burn himself
Lol you know the water is just to get a good seal doesn’t matter if cold or hot lmfao
Uve got a point there lol 😂 i think they call it PPE 😬😷👍
Plus wouldn't you scold yourself as its a liquid not burn yourself
@@justinalexander4166 it also softens the metal and paint so it doesn’t crack or chip
Yes this does work and is not only done on plastic. The hot water isn't to make a seal for the plunger it's to make the paint soft so it doesn't crack along the creases of the dent . It's easier to flat and polish clear coat than it is to repaint a whole door because the paint cracked and came off in one chunk.
Always wear slippers and shorts when boiling water in the area. Please remember.
He looked round to make sure no neighbors were seeing him look like a tweaker with a pot and plunger 😂😂
Boiling water is one temperature, it can't be hotter unless pressurised or colder then it's not boiling. Unless at higher altitude pressures. Genius Man.
You can microwave water which can heat it past 100C without boiling
Now we just buff out all these poop skid marks from the plunger and were done!!
I think he wanted to remove the poop marks from the plunger, but being too drunk he just included a car side to make his thoughts exceptional...just a Musk..
😂😂
Ba dum tss
😂😂😂
😬
I knew a guy who worked at a car dealership way back in the day, and said they used the old plunger trick then too. Said it worked like a charm.
the plunger just by itself or w the boiling water too?
Thank you much for this video. I have a small dent on the drivers side of my door (2017 Toyota Corolla) I pulled up at the gas station opened my door and hit the "U” shaped barrier next to the gas pump. I’m happy I viewed your video. Guy was asking me for 50.00 to repair this minor dent.
I’ll show my son your video, have him do it for me. Again, Thank you! 🙏🏽 Unlike some trolls here making fun of you. They have no respect. Me - I appreciate your video. 👍😎
Remember it can't be boiling too hot😂
What’s wrong with that? What’s the right way then.. 🤔
@@j.danielrobles7529 LMAO
@@trylessego exactly! So what if he said like that. Don’t be so boiling hot 🥵 😡 LMAO back at you!
@@j.danielrobles7529 well boiling water is 100 degrees centigrade? So is it actually boiling water you use or not??
@@j.danielrobles7529 you such a genius LMAO
Proceeds to dent tf out of the door pushing the plunger hahahahaha
Should my water be a low boiling, medium boiling or high boiling? Thank you... 🤣
it could be all of them, but mostly just not too boiling, ok? hope that clears it up. 😆
Hahaha let’s just say slightly boiling hahahah
LMAOOO
Lm😂
Plot twist : that's how they do it in the workshops and charge us hundreds of bucks 😶
Plot twist, no they don't.
@@StallionFernando yeah, they don’t do anything
Probably just use industrial plungers without boiling water cause i dont believe the water is needed
They actually just spend time thinking about what other problems they can make up and how high they can charge you without you complaining too much
@@BossKnighto
Making sure no neighbors are looking at him plunging his car. Especially that loud mouth teasing neighbor. 😂
It doesn't have to be boiling water, water from a hose will work just as well. The water is just to help the plunger seal better. Also a sink (red rubber one) plunger works better. I've done without any water at all before.
The hot water is to make the paint soft so it doesn't crack at the dent creases .
It works really good with just warm soapy water too
Not too warm tho!
How'd u do that?
@@criticalpapaya pretty much the same as this method except you don't have to worry about dealing with boiling water and melting stuff
Today were gonna show you how to remove skin from your feet.
Lmfao 😂😂
😂🤣🤣🤣🤣you won the best comment of the day🏆
Someone doesn't understand what "boiling water" means
😂 but not too hot boiling..
He said, "you want it boiling... but not boiling boiling"
*brings water to the slightest boil*
“This is boiling hot now”
He turned 1 dent into a whole dent family
Remember to wet the plunger to get a good hold on the panel
Works more efficiently with a sink plunger rather than a toilet plunger.
“With boiled water”
Once removed from the heat source, it stopped boiling.
Counter intuitive but if you were to knock that crown down in the middle between the two dents it would have maybe came out, that’s holding most of the tension in the metal
Great idea..lol
Only if you have a car with Tin Foil for a body.
This Won't work on an older/stronger steel body
Worked on my 1989 ltd crown vic, actual suction cup too. Popped right back
Hahaha Tun foil like the fool of oz hahahha
I can appreciate this yes...and may get around to trying it out...I've a dent in just about the same place very slight too
Boiling water, bare feet in Flipa de Floppas and an idiot. Perfect fun viewing.
“Can’t be too hot or it will remove the clear coat “…….pours boiling water onto paint
Just a class note, water , once boiling, will not reach any higher temperature.
Only way to get water above boiling temp is in a pressurized atmosphere
Make sure it's not boiling too hot. Mate water only boils at one temperature
Bare feet and boiling water a great combination.
You can skip the boiling water and use a hair dryer if you want... Unless you just like waiting for water to boil
*immediately starts making dent worse*
Go inside and remove the door panel and roll the dent out.
Remember kids, the water can't be boiling too hot! 🤷🏻♂️🤦🏻♂️
Soon as I saw him wearing a pink sleeveless t-shirt I knew there was trouble.
Oh so this is why my neighbor was doing this the other day thought he was doing a dumb tik tok.
It can't be boiling too hot? I'm not sure what you mean. Water boils at 212°F(100°C) at sea level. Once it starts boiling, no matter how much heat/energy you put into it, the temperature of the water will not go over 212°F(100°C). The steam, however, is another story entirely
No dent in my car .. i watched to see you👀😊😂
Next video in the series was on personal protection equipment
Boiling but not too hot? What? Boiling is Boiling 212 degrees
At sea level, in open container. As you rise in elevation the boiling point goes down. If you cover and restrict the steam, the steam temperature goes up.
@@davidyetter5409 that's a meaningless distinction considering that he's pouring it out of an open pan.
@@paulheitkemper1559 Just referring to the basic laws of physics. Nothing more, nothing less.
is that a gtr??
Worked great good job
"Make sure the boiling water isn't TOO hot"
"Boiling" is literally as hot as liquid water can possibly get...
Great job man
What a shitty way to do it. Hopefully your door is flushing fine now.
Don't try this on Tesla, the water will go through misaligned panels and right into the car.
Explain how that boiling water won't destroy your paint??
The boiling water makes the paint soft so it doesn't crack at the creases of the dent. It's easier to repair dulled clear coat than to have the whole door resprayed because the paint cracked down to the metal.
Made the debt ten times worse genius
Didn't even see a dent in the door, let me put a dent in it for you then try and use the method. Now that would be a video clip too watch and you would get more views and likes.
I was trying to find it too
U had the wrong plunger, the purpose of that design is to push the stuff down waste tp ect, the other pulls up n sucks with out the center ring
Boiling water is always 100°C, otherwise is just hot
Am I the only one who waited for the whole door to come off?
By boiling water you mean hot water because it stopped boiling the instant you removed it from the heat.
Yeah, gotta use that slightly less hot boiling water. 🤣🤣🤣🤣
That’ll leave swells in the paint
Boiling too hot? Are you at sea level or just spaced out!
So medium boiled water is OK? Juan, kick the dent in with spike shoes and show the hack again
What do you mean by “ it can’t be boiling too hot”? It either is or it’s not
As ridiculous as this video is your title got me to watch it because I couldn't believe someone would try this and think it actually works
That works on plastic not on sheet metal. Unless your driving Noddy’s car
ua-cam.com/users/shortsFajicGcDuls
@@IanJesting that wasn't metal, that was a plastic panel.
Sounds like metal to me
@@StallionFernando metal panel, try again.
Definitely metal.
Um it's easier to remove the interior door panel and work the dent out with proper tools smh
Plus boiling water, or almost boiling water, doesn't heat metal enough to make it plyable like it does when poured over plastic. What this kid did was he saw a video and stole it in order to get clicks or as the "cool kids" would say, get me some "clout". I agree. Take the inside panel off and work with real tools. I think it's maybe 4-6 screws to remove the panel. I think he actually dented it more and he even paused but caught himself doing more damage
The way he said toilet plunger
Any water work it’s just to make a seal
No . Hot water stops the paint from cracking at the creases of the dent .
Ty,that was so helpful !
The water don't have to be hot killer You just need suction
Oh I will be using this!
Just curious as to how much boiling I should apply to my pot of water?????
How to kill grass with boiling water
Eso podría funcionar en mi Tesla, si tuviera un Tesla.
Did you just like yourself? Lol
Cant do this on a classic car
Im more concerned about him holding that plunger so close to the bottom
You should never see boiling water with flipflops
"Use boiling water.... but it can't be boiling too hot." Seriously bro?? 🤔🤦🏻♂️
It doesn’t look like it did shit. No pun intended
So is it supposed to be boiling or nah? I don’t know what you mean by not boiling too hot😅. I’m British, there’s no such thing lol
Trying to pull one dent end of putting 5 more
What's that Brown spot on your car door bro
Just flush the whole car down the toilet 💀
I thought the door was gonna come off with the plunger 🪠
The water is no longer boiling once you take it off the heat source .
PUT SOME DAM SHOES ON AMERICA! YOU AINT IN JAIL!!!
Yes but this only works on the newer models that are trash aluminum
I’m going to try this. Someone punched my car and dented it.
So what do you do for the shit stains from the plunger?
Where is the dent?
Can anyone tell me where is the dent??
There’s no dents on the door where he poured hot water.
I don’t see any dent on the car at all,
I mean there is no dent in first place on that car when he pour that hot water. This guy is trying to make a fool of everyone here just to see his video
Wait did it work?
Don't be that guy, running around with sliders and hot water in a pot. Put yourself some pants and proper shoes.
If it's boiling water it is very hot - simple phisic.
Bro holding the plunger way to close to the end with no gloves 😮
rip
I like my boiling water not too boiling.
Huh.... boil the water but dont boil it to hot. wtf does that mean?
Did it work?
That toilet plunger has seen worst.
Pdr cold glue
Looks that plunger been taking alot of shit