Magic from 05:48 ... physical swith is OFF, but app can turn the light ON (and OFF). Cool. Thanks to the pull-up resistor in the Sonoff Zigbee Mini ... so the physcial switch status/action is just a *signal* to the Sonoff Zigbee Mini (and not acting like a real power switch). Thanks for the video!
This is great, thanks for the video! I was wondering how it would behave it I switched it on in the app and tried to switch it off with the regular switch, but as it turns out it's not a problem!
Yes, the only issue if you use the phone and physical switch as well, the position of the physical switch (if it is up or down) will no longer reflect the state of the light.
Szervusz Csongor! Azóta sem tudja a ZBMini a rögzített fel-le pozíciót? Esetleg vmi egyedi firmware flash? Vagy tudsz esetleg erre alternatívát? Eddig csak a Shelly-kben láttam ezt az opciót, de az ugye wifis...
I saw written that ZBmini works with Google Assistent. I never got Zigbee working in Google Assistent. I never found a video on UA-cam where I saw Zigbee working with Google Assitent. Maybe you could make a video where Zigbee devices working with Google Assistent.
Can the ZigBee mininbe used with a push button switch? I want the operation of the ability to turn the light off with switch and app. But want the switch to remain in one position. Can a "door bell press" style button turn it on off with the internal relay?
Good video. If wiring a new room/house is it best to use this switch and does it have to be located behind the switch. If it is located at the switch then you will have a lot of cables coming to the switch especially if you connect two manual switches. (power in and power out, cable to the light, cable to the next switch) What is best practice? Easier to access if it is behind the switch?
I don't think there is a best practice. In an existing house, behind the switch is the obvious place. You will always have two wires to the switch and back, and you can reduce those if those are close.
Congratulations for your channel. An easy query for you.... From the entrance of the house to the garage we had a button to open the automatic garage door, I had to replace this button with a switch (there are no buttons for this model, don't ask me why) and I have a couple of Sonoff Zbmini for that is what I want to use and would like to know if it is possible for this ZBMini to act as a button to activate the door in case of any change in the state of the switch. I am using zigbee3mqtt in home assistant. I imagine that with node-red it can be done but I still haven't finished understanding node-red and I'm still very new in home automation. Please can you give me some idea? 🙏 Thank you.
Thanks. I have not tested the zigbee mini with Zigbee2mqtt or ZHA, but I am pretty sure it can be done. It just need to be configured not to toggle the output, but only to generate a short pulse.
Nekem van egy 'zárt' (értsd csak a kinti kapcsolónál tudok hozzáférni a vezetékhez meg a kapcsoló szekrényben) kültéri lámpa amit távolról akarok vezérelni. Van nekem máshol sonoff RF 433. De az nem fér be a kapcsoló mögé. Ezt talán de nem találom, hogy 433-as távirányító vagy kapcsoló programozható rá? Vagy van valami ami hasonlóan kicsi relé és igen? Köszi!
I don't own a Hue zigbee hub. I tried pairing the Sonoff zigbee devices to a Tuya Zigbee Bridge and all worked except one. I think the Zigbee bridge is a generic device and that has the highest chance of working with any Zigbee bridge.
Good question. I would say that if that ecosystem have similar zigbee sensors (like motion sensors, door sensors), there is a very good chance that they will work.
I don't know. I am assuming it is connected directly to the microcontroller pins, or maybe via a opto isolator. If anything it could be on logic level 3.3V, but maybe it is just left floating, and when the swich is on, it is connected to ground.
Yes of course. Probably the only issues if if you have enough space for the mini behind the socket. They tend to be deeper than a regular light switch.
Im using these two in garage and put switches ring like without fixation (click) to avoid the switch to be off and lights are on situation( dissynchronization) and im facing that if i turn lights pressing the switch instantly all is good, if i click it for a half second more, they turn on and after release lights turn off ( switch processes it like another impulse) Any way to deal with this issue? Any settings or hardware hacks about that?
You can replace the regular switch with this smart switch and control a LED strip. But this switches mains voltage, so the LED driver/power supply is to be connected after the switch.
@@csongorvarga I watched this video, but i cant see all settings made in it, and so i cant repeat it. Can you gave me some tips hot to recreate it? ua-cam.com/video/K-jov9Cvxcw/v-deo.html
This device could have been my choice to make my wall switches smart but the fact that it does not support push buttons is a shame. Great video though!
@@csongorvarga currently I don't have a neutral line so I'm going to fit this in to the ceiling panel light. I think basic one not going to fit inside the pannel light
Exactly the same way. Press on the button for more than 5 (10?) seconds and it goes into pairing mode. After that you should be able to add it to SmartThings.
@@csongorvarga Ewelink is NO Google Assitent. Show any Zigbee device working with vioce in Google Assitent with normal gateway (Tuya, Sonoff. NOT Smartthings aso). When you see the device in Google Assistent, you see the icon with setting wheel that's all.
@@csongorvarga Everywhere you see by ZIgbee "Works with Google Home/Assitent. You say "these devices", but show me which Zigbee device (you may choose) works with Google ..... On Aliexpress e.g.: ZigBee Smart DIY Motorized Roller Blinds/Shades Drive Motor Hub Tuya Smart Life APP Alexa Google Home VOICE Control. This don't work! Show me if I'm WRONG
Magic from 05:48 ... physical swith is OFF, but app can turn the light ON (and OFF). Cool. Thanks to the pull-up resistor in the Sonoff Zigbee Mini ... so the physcial switch status/action is just a *signal* to the Sonoff Zigbee Mini (and not acting like a real power switch). Thanks for the video!
Yes it is. And therefore the physical position of the switch (whether it is up or down), will not be in line with the state of the light.
@@csongorvarga and do you consider that an advantage or disadvantage?
@@csongorvarga "up or down" ... that is for American-style switches, right? In Europe, a switch has no up or down.
@@blablamannetje well, the top side pushed in, or the bottom side pushed in. Still you sort of get used to it
Thanks. I couldnt find explonation on how to connect dimmer switch to a normal traditional switch. Thanks to You i know how it will work.
Can it be used in a three way switch circuit ( two switch es controlling one light like in a hallway.)
Great video!! I finally understood why I would get one of these as opposed to a regular smart switch.
Great video. Between the sonoff and switch, have you done S1 to com and s2 to l1 or l2? How come you use 1 live and 1 neutral wire? Thank you 3:51
I'm late to the party on this one but thank you for covering how the app switch works in relation to the state of the physical switch (@ 05:55).
Between all videos if found out this one with my rusty english as the best understandable one. Many thanks. 👍
Thanks a lot mate. I am glad was able to help.
Hi, one question in case the wifi is down the mechanic switcher would still work ?
yes
just wondering if you tried to pair with Tuya ZigBee hub?
This is great, thanks for the video! I was wondering how it would behave it I switched it on in the app and tried to switch it off with the regular switch, but as it turns out it's not a problem!
Yes, the only issue if you use the phone and physical switch as well, the position of the physical switch (if it is up or down) will no longer reflect the state of the light.
@@csongorvarga Well that isn't really a problem :D
Szervusz Csongor!
Azóta sem tudja a ZBMini a rögzített fel-le pozíciót? Esetleg vmi egyedi firmware flash?
Vagy tudsz esetleg erre alternatívát? Eddig csak a Shelly-kben láttam ezt az opciót, de az ugye wifis...
Dear Csongor, I want to use the zigbee technology first time. What is your suggestion how to create a controllable contact switch with zigbee. Thanks
does it save state after power cut off?
I saw written that ZBmini works with Google Assistent. I never got Zigbee working in Google Assistent.
I never found a video on UA-cam where I saw Zigbee working with Google Assitent. Maybe you could make a video where Zigbee devices working with Google Assistent.
You need a zigbee controller/hub. e.g. smartthings.
GA doesn't have a built in zigbee hub.
Can the ZigBee mininbe used with a push button switch? I want the operation of the ability to turn the light off with switch and app. But want the switch to remain in one position. Can a "door bell press" style button turn it on off with the internal relay?
Szia Csongor. Sajnos nem találom az inching funkciót. Tényleg nincs benne csak a Wifisben? Nagyon fontosnak tartom ha rövid jelre van szükség.
Igen, a Wifis-ben találtam meg csak én is. Szerintem is egy fontos funkció és kihagyták.
@@csongorvarga Köszönöm így már legalább nem keresem tovább. Remélem egy frissítéssel egyszer működni fog. Vissza is veszek a Zibees átállással.
Good video. If wiring a new room/house is it best to use this switch and does it have to be located behind the switch. If it is located at the switch then you will have a lot of cables coming to the switch especially if you connect two manual switches. (power in and power out, cable to the light, cable to the next switch) What is best practice? Easier to access if it is behind the switch?
I don't think there is a best practice. In an existing house, behind the switch is the obvious place. You will always have two wires to the switch and back, and you can reduce those if those are close.
Hi, does this work with RF remote control as well? If i connect 5 of them in my dining room can i use RF remote to switch it on and off
Congratulations for your channel.
An easy query for you....
From the entrance of the house to the garage we had a button to open the automatic garage door, I had to replace this button with a switch (there are no buttons for this model, don't ask me why) and I have a couple of Sonoff Zbmini for that is what I want to use and would like to know if it is possible for this ZBMini to act as a button to activate the door in case of any change in the state of the switch. I am using zigbee3mqtt in home assistant. I imagine that with node-red it can be done but I still haven't finished understanding node-red and I'm still very new in home automation.
Please can you give me some idea? 🙏
Thank you.
Thanks. I have not tested the zigbee mini with Zigbee2mqtt or ZHA, but I am pretty sure it can be done. It just need to be configured not to toggle the output, but only to generate a short pulse.
Nekem van egy 'zárt' (értsd csak a kinti kapcsolónál tudok hozzáférni a vezetékhez meg a kapcsoló szekrényben) kültéri lámpa amit távolról akarok vezérelni. Van nekem máshol sonoff RF 433. De az nem fér be a kapcsoló mögé. Ezt talán de nem találom, hogy 433-as távirányító vagy kapcsoló programozható rá? Vagy van valami ami hasonlóan kicsi relé és igen? Köszi!
Nem, ebben nincs semmi 433 RF resz.
Hi
Thanks for the video, just to can confirm, this switch can be paired with the hue zigbee hub? So will this be available to HomeKit , once paired?
I don't own a Hue zigbee hub. I tried pairing the Sonoff zigbee devices to a Tuya Zigbee Bridge and all worked except one. I think the Zigbee bridge is a generic device and that has the highest chance of working with any Zigbee bridge.
Hello. Thanks for review. Probably it is first on on UA-cam. Is it possible to make it work with button type switch?
Thanks. Maybe with a future software version it will be possible.
Could you give an example of how you would connect the S1 and S2 when using this as a two way switch?
Please check this diagram: img.joomcdn.net/b4ea6372cfe3161adb835cc6a0a21497e8d00b77_original.jpeg
Hi. Thanks for the video.
Does it work with the Sengled bridge?
Good question. I would say that if that ecosystem have similar zigbee sensors (like motion sensors, door sensors), there is a very good chance that they will work.
Do you know on which voltage S1/S2 operates (light-grey contacts) ? Can I use LED indicators and of which voltage? Thanks
I don't know. I am assuming it is connected directly to the microcontroller pins, or maybe via a opto isolator. If anything it could be on logic level 3.3V, but maybe it is just left floating, and when the swich is on, it is connected to ground.
Sapresti dirmi come inserire un condensatore per eliminare le interferenze e quindi le accensioni random tra s1 e s2
Grazie
Can this be used with regular plugs/sockets?
Yes of course. Probably the only issues if if you have enough space for the mini behind the socket. They tend to be deeper than a regular light switch.
@@csongorvarga Thanks. Will check ;)
is this end device or router?
Im using these two in garage and put switches ring like without fixation (click) to avoid the switch to be off and lights are on situation( dissynchronization) and im facing that if i turn lights pressing the switch instantly all is good, if i click it for a half second more, they turn on and after release lights turn off ( switch processes it like another impulse)
Any way to deal with this issue? Any settings or hardware hacks about that?
Sorry, I have no idea why this happens
hello, Can you tell me how I can wire the ZB Mini if I only have a motion detector instead of a normal switch?
You mean a zigbee motion detector, or some regular motion detector?
@@csongorvarga a regular motion detector with 230V
Can I use this to controll a seperate (plugged in a different circuit) LED Strip on/off with regular switch?
You can replace the regular switch with this smart switch and control a LED strip. But this switches mains voltage, so the LED driver/power supply is to be connected after the switch.
I have a light switch that only has a live in and live out, can this unit work with such?
No, this also needs neutral wire.
@@csongorvarga thanks bud!
Hi, have you try to connect and extract sensor data from xbee in node-red?
Not yet. I don't have a gateway which works with node-red yet.
@@csongorvarga I watched this video, but i cant see all settings made in it, and so i cant repeat it. Can you gave me some tips hot to recreate it?
ua-cam.com/video/K-jov9Cvxcw/v-deo.html
Does it work without a switch?
Yes, it works
Hi QQ please ! can i use sonoff mini to controle a motorized blinder (up/down) ?
No, unfortunately. This mini has only one output, and blinds usually require two output, one for up and the other is down.
@@csongorvarga thanks for your kind help
Does it work with the Hue bridge?
Sonoff said that is. And as far as I am aware Zigbee v3 devices are cross compatible with Zigbee hubs.
Thanks for vid. Another good one thanks
This device could have been my choice to make my wall switches smart but the fact that it does not support push buttons is a shame.
Great video though!
well if it is an mechanical switch which does not have auto return it will work
It works with push buttons!!! I installed it last week.
Can I use this without the switch?
Yes, of course. But there is also a Zigbee Basic, that does not have a switch input. That could be cheaper, so check that as well.
@@csongorvarga currently I don't have a neutral line so I'm going to fit this in to the ceiling panel light. I think basic one not going to fit inside the pannel light
@@pn670 Oh yes, makes sense. Mini is lot smaller and better form factor.
can i pair it with hubitat without sonof bridge?
That is a good question. Most probably you can link it, and probably it is going to work as well, but there are no guarantees.
In my ewelink app theres no zb bridge and i can't connect my sonoff zbmini L, help
Zigbee bridge is a device you need to purchase and pair it to the ewelink app first.
Can this work with smart life app
No, only with eWeLink.
I am the son of Zigbee !
How to pair to smartthings?
Exactly the same way. Press on the button for more than 5 (10?) seconds and it goes into pairing mode. After that you should be able to add it to SmartThings.
Dont have last state??
No, does not.
@@csongorvarga today i try It 😢😢😭😭
Thank you
@@csongorvarga And is the default after power-off on or off?
@@p0iss0n Default is Off
Nobody can show zigbee working with Google Assitent??? So "works with Google Assistent" FAKE??? Well mr Csongor Varga, you know so REPLY!!
What do you want to do? Did you link your eWelink account to your Home app?
@@csongorvarga Ewelink is NO Google Assitent. Show any Zigbee device working with vioce in Google Assitent with normal gateway (Tuya, Sonoff. NOT Smartthings aso). When you see the device in Google Assistent, you see the icon with setting wheel that's all.
@@rebe7800 It does not work like that. Or at least not with these devices. These do not connect directly to Google Assistant.
@@csongorvarga Everywhere you see by ZIgbee "Works with Google Home/Assitent. You say "these devices", but show me which Zigbee device (you may choose) works with Google .....
On Aliexpress e.g.: ZigBee Smart DIY Motorized Roller Blinds/Shades Drive Motor Hub Tuya Smart Life APP Alexa Google Home VOICE Control.
This don't work! Show me if I'm WRONG