How to Upgrade Yamaha Receiver Firmware
Вставка
- Опубліковано 16 жов 2024
- In this video we walk through upgrading a the firmware using the front buttons on a Yamaha receiver.
Below you will find some receivers that you can purchase from Amazon.com:
Yamaha RX-V681BL 7.2-Channel MusicCast AV Receiver with Bluetooth @ Amazon.com: amzn.to/2Gl5fVB
Yamaha AVENTAGE Audio & Video Component Receiver,Black (RX-A670BL) @ Amazon.com: amzn.to/2DF53ma
Yamaha AVENTAGE Audio & Video Component Receiver,Black (RX-A770BL) @ Amazon.com: amzn.to/2DDgVFc
Yamaha AVENTAGE Audio & Video Component Receiver,Black (RX-A870BL) @ Amazon.com: amzn.to/2DO2626
Worked like a charm, thanks. Some advice though... your amp shouldn’t sit directly on your surge. Excessive heat can damage your amp. Even if you put some small 1x1 pieces of wood in between them it would help so heat doesn’t build up between the devices.
I have no clue what I'm doing and I've watched countless videos. Yours was simple and to the point however leave it me to get device error ugh. I'm going to check out your channel to see what else ya got. Thanks
Thanks tons Erik! Still helping folks in 2021!
2022 also :)
Thanks. You just helped a family in Brazil.
Excellent video!!’ Straight to the point and helped me out!!! Thank you!!!!
Thanks!!! Just a heads up. It seems that if one has the latest firmware, the amp displays "system error".
Excellent video. Just updated two RX-A880 receivers.
Thank you! Helping folks in Sept 2022!
Awesome! Heads up for a Yamaha RN500 you need to shut off the receiver first and then press return and power at the same time. Afterword use the scroll wheel to cycle to update. Press return to switch to network. And the. Press display to begin network firmware update.
Thanks so much for this, so frustrated at the moment.
This is exactly what I needed, thank you!
It worked for my RX-v679. I had to make sure the zones were completely off. Then followed these steps and it is updating. You will see the *** and some info below it on the display. E.g. S1-15:45%...this was my experience. Your's might vary.
good job dude. Worked like a charm.
👍 you rock! (From France, July 2024) 🙂
Awesome video! I just updated my RX-V681 to 2.65 and realized the update removes vtuner internet radio and replaces it with Airable radio.. is there anyway to go back to the previous firmware? or can a factory reset restore previous firmware?
Please, do you know how to update Yamaha n-r602 firmware to get not only 80 watts per 2 channels in 8 ohms, but 115 watts per channel in 8 ohms? I read the Manual 6 times, and I didn't find a way to do so. Someone said that I've to send a letter to Yamaha Company to do the "trick". But Yamaha Company is very confused... Example: when asking my phone number, there's no space to put my phone number completely. It's being very hard to dialogue with Yamaha Company, like other companies nowadays (Amazon, Google, Microsoft, Dell...).
I think they don't want to receive e-mails from any person. Do you know how to get the upgrade firmware from a 2 channel Yamaha Receiver, please?
Worked like a charm! Thanks--can't believe it was that simple. THANKS!
I got an Av681 or something like that. Just bought a 4k projector. Amp wont put a signal from my shield to the projector. Would a flash upgrade fix it?
I am not sure since I don’t have personally have that particular setup. However, it would probably be worth a try to upgrade and confirm the results.
Anyone know if we can get the rear speakers to work at the same time as atmos? Will this receiver ever be capable of doing that? If not what yamaha receiver can? I like the berr brown daks so I’d like to stick with those. Also I want preamps on every channel as I run separate amps. Which a lot of the new yamahas don’t have the separate preamps. But I’d like to stay in a decent budget. Not trying to spend thousands
Worked for an RX-A3000
Thank you
I have Yamaha 480 receiver.
Is there anyway i can upgrade it to 720 or 1080.
I am not able to connect my viewsonic projector.
Thank you
Thank you for this. Saved me digging out the manual.
Thanks I been trying to do this for almost a year
Best video ever. Thank you so much 🎉
How do I hook up receiver to even get a firmware update?
Thanks for the help! It worked perfectly.
followed your instructions and got a "device error message" Now what do I do?
Thanks for your help. I will watch this a few more times. :)
Thanks, brutha!!
Much appreciated!!
my old R-N301 doesnt have a "straight" button, noe do i have the remote controller lol.....wtd??
That worked great! Thanks So Much!
Thanks for this.
My RX-A760 has been showing verifying for at least ten minutes. First time was ten minutes and then said "Not Found" ... My firm ware is showing at 1.21 I think. New one is at 2.60. Using Cable for network ... Any ideas?
someone know what is error! 0100001 ? It happens to me at the end of the update
It worked! and also on my RX-A1070. THX
How long did it take to verify? Been an hour now on my 1080.
This video help me a lot... Thank you for your help...
I have a similar receiver but mine is not WiFi, when i plug the Ethernet cable it does not register a connection. Any ideas?
I've found multiple videos for updating via network but I don't believe my rx-v385 connects to the internet at all. Is there a video somewhere showing how it works when you update via USB? Having lots of issues. :/
Hey, did you ever figure out how to update it? I have the same receiver.
I need help , it kept saying not found after verifying .....
hello hopefully you see this i have the rx-a3080 with usb it reaches the step 6 then failed internet method it says file not ready immediately and the firmware version is not showing in the settings i tried everything and nothing
Have you verified that you have a good Internet connection? You could verify this by trying to stream Spotify or some other music app built into the receiver ensure the music plays without any buffering.
@@ErikAsquith thanks for responding yes tried that it’s working fine no issues e there this error comes up 000400 with the usb and noting about on the forums
@@MultiTHEJOKER unfortunately I am not familiar with that error code.
Amazing thanks
during an update it shows file not ready?
U mnie to nie działa Yamaha rx-v 671 . Nie lonczy z internetem
Anyone know if you can route any output to Zone 2?
Thanks man
Thank you.
Thank you for your video
Thank you :-)
Thanks for that.
Mines doesn’t have an update option
what does it mean if it says file not found?
Are you updating via network or a USB thumb drive? It sounds like it not finding the firmware update file.
Thank you it help for me
Just gets stuck on verification ...even with usb ...
U mnie kończy się na veryfing i device error
Can I put the RX-V383 firmware on the RX-V377?
Nah. Don't do it...🤘
Why did it say power off and you said you can power the unit back on and you press the power button? Wasn't the unit already powered on because it said to power off. Just a little confused
It automatically powers off the unit if you do not press the power button (you can see the red light indicator illuminate next to the MAIN ZONE button). After the unit turned off automatically, I pressed the power (MAIN ZONE) to power the unit back on (and the red light indicator turned off). Hopefully that helps clarify things. But either way, if you get to the Update Complete and Power Off! appears on the display, you've successfully updated the firmware.
Erik Asquith Thanks
How long would it take until network update will finish? Any time table? Mine took forever, can i just unplug it while AV still verifying?
@@icerthym31ski it all depends on your connection speed. I would not personally do the update unless you were hardwired into the unit. I just don't trust Wi-Fi all that much when you're doing firmware updates. If you have decent amount of speed through your ISP it shouldn't take more than 10 minutes. And no do not unplug anything until it is completely finished or you will screw up your receiver. You need to let the update finish and turn off the unit.
icerthym31ski I had performed the firmware update via WiFi. The entire process took less then 10 minutes.
Thank you very much!!!!
Make sure you download the update to your computer, then unzip (extract) the file. Then save the .bin file to the root folder on the USB drive to do the update. Otherwise, it won't work.
Is there an upgrade to fix the very annoying high frequency noise coming from the RX-A3070 receiver? Worst receiver ever had.
Just got the receiver and some times I get static kinda like white noise out of my speakers
@@dayonerecoverdub3626 Check your connection. It sounds like you might have them some wires crossed or reversed. Or Turn down zone 2 If it is up to high it will distort zone 1.
Mine says file not ready any idea?
MrZACATECANO100 are you seeing that message before or after the download completes?
Erik Asquith before, I updated again after a few minutes and it did do the update completely. Thanks though for the video.👍🏽
Dear Sir, do you have firmware for RX-V375? If you have it, could you share to me? I have a problem. Thank you.
Yamaha AV receiver htr 2067 power problem
it says file not ready
Hel[p
Sorry, I am not sure why it is displaying that message.
THX.
Thank you. It’s bizarre why Yamaha has to have people dig for something like this rather than just have it somewhere in options or menu. Ugh.
Do you know why I can't get atmos to work? Lol
Unfortunately, no. I would need much more detail as to how it's not working and what you are doing to get it to work. How do you know it is not working to begin with?
@@ErikAsquith because it only says dd+ when I stream atmos movies on netkfix. I can hear the up firing speakers but it’s so soft. No way the sound can effectively create the overhead sensation.
I had the receiver setup on basic and have a 3.1.2 system and then .2 is the up firing speakers that sit on top of my 2 channel speakers ( I hope that makes sense)
I have the tv ( Sony oles) setup to play DD+ since I don’t see atmos option.
Thank you!!
@@leonidvedine when something flies overhead, like an airplane, does that sound get louder and come through the up firing speakers? You won't get much sound up of those up firing speakers until there is an object producing sounds overhead.
@@ErikAsquith not really. its certainly not obvious.
Hello Sir how update RX a1020..
Спасибо!
sparks1967 d you are welcome. Thanks for watching!
Erik Asquith what do u do if a error comes up while trying to verify and can you do a vid on how to connect it up to the internet
About earc update is real
Did not work
Woops, yes it did
Johnny Parker did you initially have trouble applying the update?
Doctor! Doctor!
Oh, I'm already cured. Thanks
I'm stuck in "remote id..." what do i do?
pressing the right arrow wont work
it worked earlier but now it doesn't