Ford Ecoboost MAF MAP IAT Sensor Cleaning - Engine Sensor Cleaning 🚿
Вставка
- Опубліковано 2 кві 2022
- regular engine sensor cleaning is vital for smooth running and economy. Let me show you our Ford Ecoboost MAF MAP IAT sensor cleaning method. Do this with your Ford 3 cyl engine air filter change.
👉 Ford 3cl oil separator and PCV valve cleaning: • Ford 3 Cyl Oil Separat...
☕ Support the channel here: www.buymeacoffee.com/CycloneCyd ☕
💡 Subscribe and hit that bell 🔔 to learn more about looking after your car.
Don't allow your Ford 3 cyl engine sensors to become dirty or clogged (especially the MAP sensor) If you find your Ecoboost MAP sensor has become clogged, be sure to investigate if your Ford 3 Cyl Oil Separator and PCV Valve needs cleaning. These systems are all inter-related and problems with one is often accompanied by problems with another.
Learn more about looking after your car:
🎥 How to replace a CV [constant velocity] joint boot with a split kit: • Universal CV Boot Repa...
🎥 Don’t let your fuel filter end up like this 100,000 mile old example:
• Why Should I Change My...
🎥 Battery & alternator care in this playlist: • Alternator and battery...
Everyone should have a tyre pressure gauge in their glovebox:
bit.ly/Tyre_press_guage
bit.ly/Pressure_Gauge_2
I personally prefer a stirrup pump to a foot pump (I use the same one for my bikes and cars)
bit.ly/Tyre_stirrup_pump
Are you trying to grow your own UA-cam channel? I use TubeBuddy, try it out for FREE:
www.Tubebuddy.com/CycloneCyd
Gear I use in filming and production:
bit.ly/CC_Gear
My videos are edited with Filmora X - try it for free
bit.ly/Filmora_X_try4free
Thank you
ford 3 cyl engine air filter change, Engine Sensor Cleaning, Ford Ecoboost MAF MAP IAT Sensor Cleaning, how to clean maf sensor, how to clean mass air flow sensor, how to clean a maf sensor, mass flow sensor cleaning, manifold absolute pressure sensor cleaning, Ford 3 cyl engine sensors, Ecoboost MAP sensor, map sensor, Ford 3 Cyl Oil Separator and PCV Valve, map sensor cleaning, map sensor cleaning spray, iat sensor cleaning,maf sensor cleaning, ford 3 cyl engine - Авто та транспорт
👉 Ford 3cl oil separator and PCV valve cleaning: ua-cam.com/video/Ybpmt_sjQVM/v-deo.html
Can you use isopropyl alcohol? Thanks
@@kharali3475 I'm not sure it would work too well, because it's not 'strong' enough. Give it a go and let us know how you get on.
@@CycloneCyd ok mate will let you know thanks
Yet another truly excellent ‘How to’ maintenance video on the Mk8 Fiesta ST. Many thanks Cyd. 👍🌟
Glad you enjoyed it!
Excellent one , many thanks
Can you also do a video on how to change those 3 sensors and the engine coolant temperature sensor on a 2019 Ford Ecosport?
At 00:30 you show turning the sensor anticlockwise with ease. I tried and the tab prevents it from turning? I was afraid I would break something and gave up. Is there a trick to releasing the tab?
Excellent video...very helpful
Glad it was helpful!
💚 All the best and continued success
Good luck,
🌸 Great video, 🌸🌸
Thank you! You too!
I have a 2015 Taurus SHO, which has the eco-boost engine. Are those sensors in similar spots? Do you know?
Really thanks !
Thanks for watching Cedric.
Very good thank you.
Now, I just need to figure out what a 'spanner' is ? (Kidding)...
Thanks!
Thank you too
Nice one Cyd, Did you get any further with that dash-cam in the Saab ?
Not yet. I had to wait quite a while for the dashcam power supply (it needs a type C power lead) as a generic micro USB one wouldn't do. And right now she's parked up with no MoT and needing a clutch. She's going to Malcolm Miles in Leicester on 11th April for a clutch (they are well busy). With the clutch slipping I can't take her for a MoT because might not get her off the brake rollers or on the ramp. I pretty much burned the clutch out making the "clutch slipping" short video!
Can i use electronic contact cleaner
I have a 2019 escape so the model before this one but my mass air flow sensor does not budge if I try to turn it. It’s not bolted in and it looks very similar to this one but when I try to twist it, it does not move and it seems as though I will break it.
I since discovered that there is a small plastic tab on the sensor that you have to lift up on allowing you to turn it. After lifting up on that I was able to turn it 1/4 turn and then after some wiggling and hard pulling it came right out: I think it was stuck in place a little because of the O-ring on it.
Thank you sir! Question????? for just cleaning the sensors, is it required to disconnect the battery cable and reset the sensors/ECU? The ignition was off the whole time. I would only think after a replacement with new ones. ? Thanks again. Cheers from Michigan usa
Apparently disconnecting for 10 min will reset them
Any idea where the Barometric pressure sensor on a 2015 Ford Focus se not 1 auto store and even ford doesn’t know anything about it.. I’m getting code p2230. I just can’t find it anywhere
It may not have one. Most cars take a barometric reading from the MAP upon ignition on and use that reading once running.
Hello. Can I use wd40 for clear the MAF sensor? Thank you.
NO, NO and thrice NO. You must use a solvent cleaner that LEAVES NO RESIDUE.
Hi can i clean the maf after i driven the car or does the engine have to be cold thanks
Yes you can. Shouldn't make any difference
@@CycloneCyd thank you
Sir, will it works on ford kuga 1.6 2015?
1.6? that'll be the duratec engine. Same process for the sensors but they'll be in different places on the engine
@@CycloneCyd thank you sir
the first sensor is not MAF it is air temp sensor.
I know so where is the maf sensor then
@@benjaminmonterosa2349 ST don't have MAF sensor have IAT near air filter and two map sensors one in the intake manifold and second in the intercooler
Wow, the clock in england works clock wise...on the right side... Everything else is on the reverse...
Did you use the mass airflow sensor cleaner for all three items?
I usually use brake cleaner or carb/throttle body cleaner. Or even soak in meths for an hour and then swish it about in the container (just don't touch the actually sensor). You can buy MAF cleaner, but the blarney on the tin is marketing hype. You don't need anything special, except that it MUST LEAVE NO residue.
Thank you for the quick response!
I have a 2015 Mustang v6. I believe it doesn’t have a MAF sensor, instead it is a MAP sensor. Should I use MAF cleaner or Carb/Throttle cleaner?
@@AMfever00either will do the job just fine. Make sure it says on the can that it leaves no residue (or on the manufacturers website).
Blow it dry when you're done and sit the sensor in a warm place for 10 mins to dry.
If you've got to buy it, go for MAF cleaner.
Ford engine bays are a mess