AMAZING! Koch Chemie GSF Gentle Snow Foam
Вставка
- Опубліковано 15 тра 2024
- I finally picked up some Koch Chemie GSF and it is amazing! Check my link below to my Amazon storefront where you can purchase it and comment below with any questions.
Amazon Storefront: www.amazon.com/shop/marty - Авто та транспорт
I find I get better foam with 50 mL per liter or a little more even. Spraying it dry works better. I do foam, rinse, foam, then contact.
It says nowhere to use 20ml in 1l witth a foam gun 🥴 it's for use in a foam sprayer. Don't understand UA-camrs. No! He didn't follow the instructions...
For foam gun use 50-100ml in 1l water according to Koch chemie. Alle depends on your pressure washer, water quality, foam gun.....
USA likes tick foam that stays 1min on panel. Europeans like milky foam that sticks longer.
All depends to personal preferences.
So gentle snow foam doesnt foam as much as mr pink per say but it works significantly better than mr pink. If you want a product that works exactly like gentle snow foam, use gt tecnic G wash, that will give you 3 times the amount of foam gsf 5 x gave you and with the same results.
I have the same foam cannon, and I use the KC active foam, at a 1:10 ratio and it’s great. You should definitely try their protector wax through the MJJC.
Active foam is next on my list for sure
With a different brand but equivalent ph neutral product, this is exactly how I do my weekly/fortnightly wash. Anytime the car is genuinely dirty I use Bilt Hamber Auto Foam. Wish I had your garage setup. Cheers
In the USA, we don’t have many choices of Bilt Hamburg products. Sometimes you can find it on Amazon but it’s very rare. I love my garage too, I’ve added some stuff since the filming of this video as well. 😉
@@WheelswithMarty Do you have water drains in your garage?
@@kcam2308I do not. My garage has a small slope so most of everything runs out. Anything that’s left over I use a squeegee to push out and the residual I use to mop my floors actually. Never waste the product! 😂
I guess my first step would be to get my floors done. Thanks for responding
@@kcam2308yea that helps to push the water out as well as the mopping part for cleaning the floor. 💪
The dilution on the Gif bottle is way too runny. 20ml=2/3 oz. You need to run a 1:10 dilution ratio for adequate foam. You did 1:9 and that seemed to work a lot better.
you need a polarizer filter to minimize glare on your lens
I have one.
I’ll be using 50 next. 😊
it says 20ml in a foam sprayer. In a foam gun connected to a pressure washer the mix is diluted approx. 1:10 so you need to use 10 times as much (maybe 5)
I use 5x and it works great
The recommended method is to use 20ml per 1,000 as a pre-wash leave for 5 mins to soak into dirt etc, rinse off then repeat dilution ratio and spray again then wash and rinse. It seems the extra foam by increasing it 5 times may look good but in actual fact is completely superfluous and a waste of money.
Hmmm I’ll try that next and see what I think about it
Anything ph neutral is useless as a pre wash, complete waste of time and product.
Youre the guy that kills the fun in everything huh?
You emptied that whole foam cannon!! what the heck, either you pressure washer is not putting out enough gpm or you just have the ratio to weak. I use GSF all the time and use half a foam cannon or less and do an entire truck. thick foam all the time. I also have a Kranzle 1122..maybe that the difference. Also a tip from someone who has tinnitus..wear some hearing protection when using your blower!! please!
If it’s my first use, I empty the cannon. Once I get my dilution figured that best suits my conditions, then I’ll use about half the cannon as a pre wash to let it soak, rinse then recoat the car with the rest of the mixture. My blower is very quiet, sounds loud on camera but it’s quiet.
mjjc rifle through soap.
Try 100ml GSF & 900ml water for better results
Yea I use that mixture some
@@WheelswithMarty - And on dry paint. The dirt on the surface will absorb the lather.
Thanks for sharing big boy.
@@laurapalmerTDGE yup! I do dry paint now as well for pre wash then hit again for contact
@@WheelswithMarty - Great! Enjoy!
oh whaou !!! and if you use the half of your bottle it will be very thick foam .... what a genious.... and you write "amazing" on your title :-)
I used 100ml instead of 20ml. Not even close to half. This is a very big bottle. I use this as my main shampoo now in my arsenal. I typically use about 50ml in my foam cannon now. It truly is amazing stuff. 😊
The obsession of bubbles confounds me. I understand that foam gives you a visible indicator of the presence of soap but is a waste of product. The cleaning solution is what lubricants, entraps dirt, pulls it down off the car. Foam doesn’t do anything. It sits above the surface.
Correct, I use roughly a 30-50ml amount of GSF and I have my mix turned down a tad. I can pre-rinse and re-spray for contact wash with one fill.
Painful video to watch.
Fail 👎🏼
How’s that? Care to elaborate?
He’s a troll bro don’t worry