VIRAGO 1100 QUICK FUEL LEVEL SETTING TUTORIAL | How to set fuel and float level in Mikuni carbs 4K
Вставка
- Опубліковано 5 вер 2024
- #viragotutorials #biketutorials
In this video, I show you quickly, how I set up the fuel and float level in the Virago 1100 carbs after an ultrasonic clean...Enjoy
If you'd like to support me with a small donation, you can do it through this link..
paypal.me/lora...
If you buy any of these products using these links, it will not cost you anymore, but will help the channel out by earning a little commission. Really appreciate it if you do. Thank you
Tools I recommend for beginner/ DIY mechanics
Sealey 4pc JIS screwdriver set ebay.us/IPnnTk
Cheap internal bearing puller kit ebay.us/dqsgMf
Wera 9 piece Long Allen keys ebay.us/jQqlHb
Wera 9 piece Extra long STAINLESS steel allen key set ebay.us/k61h1m
Wera 9 piece Short Allen keys the one in the video ebay.us/GSp19W
Wera 9 Piece Short BALL END Allen keys ebay.us/YwEiE4
Wera 6 Piece Screwdriver lasertip set ebay.us/C1stL5
Clarke CDM35C Multimeter in MachineMart bit.ly/2uNOKA8
Parts I purchased for my Virago 1100
Bearing I used for the swingarm Koyo 30203JR ebay.us/kKwNk7
The seal I used for the swingarm SKF CR25x40x5HMSA10RG ebay.us/F5m9iL
Camshaft bearing I use FAG 6205 C3 ebay.us/3oWoLQ
Spark plugs BPR7ES ebay.us/n6SKB3
BP7ES ebay.us/yuRqPp
Air Filter ebay.us/RlLUeh
Exhaust gaskets ebay.us/3rYnc4
4L Engine oil Motul 7100 20W-50 ebay.us/ovRAWl
Oil Filter Hiflo ebay.us/skiaTn
Final drive oil Motul HD 80W-90 ebay.us/gSlwPx
Front Brake pads Brembo CC you'll need 2 sets ebay.us/PyqGrZ
M7 x 1.00 Bleed Nipple in Stainless Steel ebay.us/wpaoX7
Tourmax MSB-201 Front brake master cylinder refurb kit ebay.us/1WdSex
All music and sound effect I use in my videos are downloaded from the FREE UA-cam Audio Library and requires no attribution.
The backgrounds I use in my videos are all downloaded from pexels.com all pictures there, are free to use in any projects....check them out (Not sponsored).
Hi Midland. Great video. However, according to the factory manual, the hose should be positioned to the left of the bowl, not the center Because the bowl is on an angle, the fuel inside it will be lower on the left side than the right side. To see this more clearly, on the bowl draw a horizontal line that is parallel to the floor you're standing to and representing the desired level of fuel (that you can't see). Draw another horizontal line that represents the bowl's edge. The two lines will form an angle like that of the carb when it's installed on the bike (about 10 degrees for the front and 5 degrees for the rear). Now, on the first horizontal line -- the one parallel to the floor - draw three perpendicular lines that intersect the bowl line: one at the left, one in the center and one on the right. These three lines have different lengths due to the 10 degree angle. The factory manual uses the line to the far left as a reference for the 1.5 to 2.5 mm spec. Your video suggests using the line in the middle, but this will actually set the float lower for the same spec, and the engine will run leaner. Make sense?
Hello thank you for your detailed comment. I agree ,and yes it makes sense. I think the difference is negligible, however it could effect the fueling. If I ever get the carbs off again I'll have a look. Thanks again for sharing your opinion.
@@MidlandCruiser I also noticed in a previous video that you initially set the float to 19mm. The factory manual says 23mm to 25mm, but I think this value for initial setup of the "hose" method. Where did you get 19mm?
Excellent video and comments, the lack of this care has owners ruining engines by mixing gasoline in oil.
You sir are very patient and top notch teacher.i have lear.ned no end of
Info properly taut by u,hats off to u my friend,keep up the good work!!
As usual a very clever shown and pure mechanical tutorial. Thank you Sir!
You're very welcome, tried to keep it simple and easy to follow 😉
Very helpful
Greetings from Brazil
Good day, please make a video where you check the float level while the carbs are fitted in the bike, then meausure in the middle of the carb, on the left of the carb and the right hand side of the carb, you will see that the "front" cylinder carb is way more on an angle than the "rear" cylinder carb... and float level will be above the "1.5 mm" the manual suggest because of the angle, wont this have an affect while driving, specifically the "front" cylinder carb?
Hello. Sorry for the late reply. I will need to do fuel level once I'm back on the project, but can't tell yet when. I will do everything to the best of my knowledge...stay tuned, sorry all I can say for now.
hey big fan first of all, but i’ve been having problems lately with my ignition switch i was wondering if know how to replace it
Hi. thank you, appreciate it. The ignition switch is held on from the back under the clocks by 2 bolts. You need to unplug it first from the harness, then remove the bolts and it pops right out, not difficult at all. I think you have to remove the headlight, then you can get to the bolts...
Hi. THis settings is the same also for the 750 mofell ? , cause the 750 modell ha a same Mikuni carb with a same jets .
Thanks. Cheers.
Hello yes, every big Virago with the Mikuni BST40 from 1988-on can use these settings.
Bonjour
I have virago 97 1100
If i can ask question about my bike
When the motor is hot
I have nose liKe loose chaîne it cover
But i open the timing chaine cover And
The chaine are not loose both side
Hello it might be your valve clearance is a bit big and making a ticking noise which will get faster if the revs go higher...check your clearance and try again. Also recommend to get a higher grade oil like a 20W-50 especially if you live in a hot country..hope this helps
Hi, i recently bought a virago 1100. I was just wondering where we can get replacement parts from a trustworthy website?
Is there any way to fix a defect rpm/tachometer?
Hi, sorry for the late reply. You can try fix it obviously but it depends what went wrong, I'm not familiar with it's inside parts so I can't help you with that. If you are in the USA and after good quality second hand parts then go on Facebook and search for Harvey Maurer in this group (Virago motorcycles and Parts For Sale/Swap) facebook.com/groups/669919913113003/?ref=share
He has loads of parts and very reasonable...I hope this helps a little 😉