BRINGING MY 90'S FORD ESCORT BACK TO IT'S BEST. Restoring The Wheel Arches And Suspension
Вставка
- Опубліковано 19 сер 2024
- Last time you saw me bring this cracking little '93 Ford Escort top spec Si convertible back to the yard with the intention of modifying it however having got my hands on the car i soon realised that it was simply too good to change so instead i will make this into the best example it can be - and in this episode that means restoring the wheel arches back to an 'as new' condition and also replacing that rusty suspension, however not everything works out to plan!
Maybe you'd like to buy this lovely example of a modern classic Ford in time to enjoy this summer? If so you can contact me by email.
My email address is johnny@johnnygetscash.com
Enjoy!
---
PRODUCT LINKS:
ABRASIVE DRILL ATTACHMENTS:
amzn.to/3HXkRQ5
amzn.to/49bwdMa
OWATROL PLASTIC RESTORER:
amzn.to/3OkGsFL
CLAY BAR:
amzn.to/3RzrKN7
AUTOGLYM POLAR BLAST SNOW FOAM:
amzn.to/3tLQV5v
TFR:
amzn.to/3tS0ShW
WHEEL CLEANER:
amzn.to/40hLA1V
APC:
amzn.to/46JGPkn
DILUATABLE DE-GREASER:
amzn.to/3QcvJx5
PLASTIC SCRAPER:
amzn.to/3s64Zq5
TOFFEE WHEEL:
amzn.to/3s1RgAG
PANEL WIPE:
amzn.to/3scyxlR
Some of the tools, materials and consumables that i use in my videos are available within the links below:
Interior Leather Re-surfacing Kit:
amzn.to/3Eoq2Xu
Intensive Tar Remover:
amzn.to/3sk0OXi
Fallout Remover:
amzn.to/3EdqTdo
Clay Bar:
amzn.to/45qelv1
Airbrush:
amzn.to/43YBxiu
Black Plastic Treatment:
amzn.to/3Jp6tl9
Toffee Wheel for drill:
amzn.to/3WA8ez9
Karcher steam cleaner:
amzn.to/3kvgWBl
Underseal Gun:
amzn.to/3yF530q
Underbody protection (Stone chip):
amzn.to/3IfvEUO
Plastic Welding tool:
amzn.to/3ORDabi
Silicone Carpet Comb / Dog Hair Remover:
amzn.to/2Wp4Njh
Machine Polisher:
amzn.to/2TL8k9W
Polishing Heads:
amzn.to/3uqTVBO
Maguiars Ultimate Compound:
amzn.to/2TXqrsc
Wet & Dry Sandpaper (240 - 2500g):
amzn.to/2TNifvD
Wet & Dry Sandpaper (Precision - 3000 - 7000g):
amzn.to/2W8MBKF
Panel Wipe (de-greaser):
amzn.to/2TVTrQU
Heat Gun:
amzn.to/3ykFoZC
Sharp Edge Tape:
amzn.to/2wVfdwk
General Masking Tape:
amzn.to/2WbiCC2
Masking Paper & Dispenser:
amzn.to/3aTf8Z2
Microfibre cloths:
amzn.to/33dC2aG
Autoglym Foam Polish Applicator pad:
amzn.to/2IFZi7Z
Meguiars Polish:
amzn.to/2wPxLyj
Clear Lacquer:
amzn.to/38JmXit
Blue Roll / Shop Cloth (For Panel Cleaning):
amzn.to/2WasawQ
Drill Brushes (For Cleaning / Scrubbing):
amzn.to/3ykQz4i
Autosmart APC:
amzn.to/2wY4tNJ
Spray Bottles:
amzn.to/3Pa1O6J
Fabric & Carpet Cleaner:
amzn.to/2TOnXxe
Detailing Brushes:
amzn.to/3IhZcRP
Wet Vacuum:
amzn.to/2W9nN5i
Bluetooth LED Beanie Hat:
amzn.to/38Kz6ni - Авто та транспорт
You're doing absolutely the right thing keeping it standard 😁
Glad you have decided to keep the car original, I'm sure you will attract more potential buyers by doing so. I have to say your standard of workmanship and attention to detail never fail to impress. well done !
Now you've shown it with 17" alloys on, I do actually prefer the look to the standard alloys it came with. Shame that the coilover experiment didn't work but I'm sure it will look good with standard suspension back on. I know last week I said keep it standard but now you made me change my mind especially regarding the alloys 😉 cheers for the vlog Johnny & look forward to the next 1 👍🏻
I knew I would be playing devils advocate fitting the 17’s in this video but I couldn’t not do it whilst the car was sat on coilovers! Who doesn’t appreciate a low 90’s Ford on big wheels?!
I'm 90% sure that the black underseal strip on the sill was actually there on the standard car, even if it wasn't rust-proofed further, the factory underside black paint did overlap to be visible. This was actually quite common on 90s cars to make the sill height appear to match the bumpers each side.
I’d keep the coil overs on Jonny having seen it, but maybe get some escort cosworth wheels just to temper the look. I mean it’s a loud car, and so you either go “lady going to shops” look, or beef it up a little. You can keep all the original bits and sell them with the car. I’d go for the OEM+ look, reckon you’ll get more enjoyment out of the project, sell it more easily (as long as it’s not too overly modified).
That shot at 11:07 is 🔥
I do like it with the 17s on it, looks much better.
That's a rewarding job, i recently refreshed the arches of my Focus, and was horrified at how much mud was hiding behind the arch liner.
Agreed. It’s one of those jobs that no one else will know has been done at a glance but you will know your arches are mint and that is somehow a great feeling 😂
What a great project and it’s looking superb. Years ago I bought an MX5 on coil overs. It was super low and grounded out on speed humps . I naively assumed I could just wind it up to a sensible height but it had dual springs so winding up the height just compressed the first stage soft springs which meant the car rode everywhere on the secondary firm springs . It had no suspension compliance and was dangerous to drive. In the end I got some used standard spec Mazda struts and everything was good from then on! 😂
Some cars need coilovers to unlock their potential, others were right from the factory. I can see that an MX5 would be pretty dialled in as standard!
The car looks mint!
I am in the middle of restoring a 1996 Astra F sedan that I bought for 300 Euros. Did the suspension lately and it was pain in the arse to unscrew the steering rods due to the age and the fact that no one took care of it in the last 11 years.
That’s the joy of working on old cars I guess! What should be a quick job always takes longer than you think it will!
A car like that should stay as standard as possible,should never go for the full chav version
Well done Johnny 👏🏼
She’s getting closer to looking like she did when she left the showroom in ‘93 everyday!
@@JohnnyGetsCash that's perfect, as it should be 👍🏼
I had a escort convertable tennis in white as my first car x ahh I miss it x
That’s cool! Funnily enough my first car was an XR3i cabriolet - it was amazing, unfortunately I simply couldn’t insure it so it had to go. I was GUTTED!
Do not delete that black stripe on sills. It matches the rubber part on front bumper and makes the car visually lighter (being a convertible with added metal braces on chassis).
Keep it stock.
It makes perfect sense to put coilovers on it it will improve it's handling 10 fold and next owner can go back original if they really want and a nice stainless exhaust is perfect 👌
The coils made sense when I fitted them, however they are just a tad too low for the look this one needs to leave with so unfortunately they won’t be staying on the car (maybe that means I need to buy another MK5 now to modify properly!)
I wonder what she'd look like with some escort rs turbo alloys on...❤
Like the work you did in the arches they looked great. Did not like the way it looked with those springs. Did like the RS wheels. I think the sills will look mint when painted. I enjoyed today's video immensely, I look forward to the next one. 👍👍👍👍👍
Thank you. The sills are now finished and look brand new (more on that in the next episode!)
I'm glad you took the standard route. I'm not a fan of the RS wheels to be honest, but the car looks fresh as.
Thanks, it will be virtually as it left the showroom in ‘93 by the time it leaves me!
@@JohnnyGetsCash she'll look mint mate.
Crazy enough I actually prefer the stock rims. 17'' looks too big for the car for me personally, or maybe because of the low height. But an amazing job!
I think if the coilovers were staying and I dialled in the ride hide front & back / maybe spaced the rears 5-10mm, the 17’s would look absolutely correct however this one absolutely does need to go back to stock!
I would have left the coilovers on the front and just had standard rear springs. Would sit nice without looking obviously lowered.
17inch alloys and lowering a inch suits the car. And I would just leave the mods to that.
What’s the story with the mk3 Fiesta?
The MK3 is in line for a good freshen up. That’s a genuine 50 odd thousand mile car. It just needs a bit of help to make it the best it can be!
I think the car looks perfect with the coilovers.. I would leave it the way it is..
I think as this one is so original throughout it does need to go back to stock, however this is making me feel that another MK5 should be bought to modify properly 😂
It’s a survivor and is best kept unmolested like it could have been 😊
Great video, can you tell me the product used to prevent rust. Cheers
Thanks. Sure, I use ‘Hydrate 80’ by Bilt Hamber as a chemical rust converter. I’ve always had good results with it 👍
Front bumpers a few shades off and the wheels it came on do nothing for it, diamond cut rs2000 wheels would look good
The front bumper is very slightly off due to the nature of plastic parts being affected by UV light differently to metal parts over the years, however this is rectified in the next episode!