I have a yale electric pallet jack with error code al06. Works fine goes up and down fwd and back, but then abruptly stops code is on al06 turn key off and on and back to use
AL06 error code can be triggered by 5 conditions related to the motor field and current issues. Here's a summary: *V FIELD NOT OK:* Incorrect voltage at the field connections causes the truck's traction and hydraulic functions to be disabled. Possible causes include loose or damaged cable connections to the motor field, or poor crimps on wires connected to F1 and F2. Verify and secure all connections. *I = 0 EVER:* If motor current levels don't exceed a preset minimum while driving, the truck's traction and hydraulic functions are disabled. Possible causes include damaged or loose electrical connections to the traction motor, low resistance in the traction motor armature (check for shorts), or a damaged controller. Verify connections, check the armature, and if the truck briefly drives but stops with code AL6, replace the controller. *HIGH FIELD CURRENT:* High field current detected by the controller causes the truck's traction and hydraulic functions to be disabled. Possible causes include loose, damaged, or shorted field wires, a shorted or low motor field winding, or a failure of the current sensor in the controller. Check the field wire connections, motor field resistance (around 0.5 ohms), and the controller's current sensor. *NO FIELD CURRENT:* Low field current detected by the controller leads to the truck's traction and hydraulic functions being disabled. Possible causes include loose or damaged cable connections to the motor field, an open or high-resistance motor field winding (should measure ~1.5 ohms), a failed field current sensor or drivers in the controller, or a damaged main contactor circuit. Check connections, measure resistances, and consider replacing the controller if necessary. *STBY I HIGH:* If the controller detects motor current during standby mode, the truck's traction and hydraulic functions are disabled. The likely cause is a damaged controller, which should be replaced. In general, this error disables traction and hydraulic functions, and depending on the condition, loose or damaged connections, motor issues, or a faulty controller are common causes. Replacing or securing connections and possibly replacing the controller are the main steps to resolve it.
please note all these conditions results in flashing the ControllerLED 6 times. We can assist you in one-on-one consultation too. Please reach out to us at info@palletjackson.com or call us at (832)239-5393
Hi, thank you for reaching out to us. Could you please specify which electric pallet jack you are referring to? It would be helful to assist you, if you brief your question more precisely.
Thanks for reaching out! In my opinion, when it comes to reliability in electric walkie pallet jacks, Toyota and Crown are two companies that consistently stand out. Each company has a strong track record of producing durable and dependable equipment. However, the choice between the two may come down to factors such as specific features, pricing, and after-sales support. I recommend considering your individual needs and comparing the offerings from both Toyota and Crown to make the most informed decision.
I have a yale electric pallet jack with error code al06. Works fine goes up and down fwd and back, but then abruptly stops code is on al06 turn key off and on and back to use
AL06 error code can be triggered by 5 conditions related to the motor field and current issues. Here's a summary:
*V FIELD NOT OK:* Incorrect voltage at the field connections causes the truck's traction and hydraulic functions to be disabled. Possible causes include loose or damaged cable connections to the motor field, or poor crimps on wires connected to F1 and F2. Verify and secure all connections.
*I = 0 EVER:* If motor current levels don't exceed a preset minimum while driving, the truck's traction and hydraulic functions are disabled. Possible causes include damaged or loose electrical connections to the traction motor, low resistance in the traction motor armature (check for shorts), or a damaged controller. Verify connections, check the armature, and if the truck briefly drives but stops with code AL6, replace the controller.
*HIGH FIELD CURRENT:* High field current detected by the controller causes the truck's traction and hydraulic functions to be disabled. Possible causes include loose, damaged, or shorted field wires, a shorted or low motor field winding, or a failure of the current sensor in the controller. Check the field wire connections, motor field resistance (around 0.5 ohms), and the controller's current sensor.
*NO FIELD CURRENT:* Low field current detected by the controller leads to the truck's traction and hydraulic functions being disabled. Possible causes include loose or damaged cable connections to the motor field, an open or high-resistance motor field winding (should measure ~1.5 ohms), a failed field current sensor or drivers in the controller, or a damaged main contactor circuit. Check connections, measure resistances, and consider replacing the controller if necessary.
*STBY I HIGH:* If the controller detects motor current during standby mode, the truck's traction and hydraulic functions are disabled. The likely cause is a damaged controller, which should be replaced.
In general, this error disables traction and hydraulic functions, and depending on the condition, loose or damaged connections, motor issues, or a faulty controller are common causes. Replacing or securing connections and possibly replacing the controller are the main steps to resolve it.
please note all these conditions results in flashing the ControllerLED 6 times.
We can assist you in one-on-one consultation too. Please reach out to us at info@palletjackson.com or call us at (832)239-5393
What's the total voltage on this Electric Is palette jack
Hi, thank you for reaching out to us. Could you please specify which electric pallet jack you are referring to? It would be helful to assist you, if you brief your question more precisely.
Awesome
thank you! Please do like, share this video and subscribe to our channel for more insightful content.
In your opinion, which company makes the most reliable electric walkie pallet jacks?
Thanks for reaching out! In my opinion, when it comes to reliability in electric walkie pallet jacks, Toyota and Crown are two companies that consistently stand out. Each company has a strong track record of producing durable and dependable equipment.
However, the choice between the two may come down to factors such as specific features, pricing, and after-sales support. I recommend considering your individual needs and comparing the offerings from both Toyota and Crown to make the most informed decision.