You made it simple for guys like me....having very less knowledge about these things. Thanks a lot for the help. Life seems easier with guys like you around. 😊
I tell you this has been my life for over 60 years 60 years with electricity airplanes cars trucks when I walk out to their car and and just a few minutes to say it is a blown fuse now white I will put a new fuse in and see what happens
electricity in autos is way different than buildings though. i have no issue touching the positive terminal on a battery. touching positive in a home/business .......hell no
Thankyou sir, driving last night and put the dipped headlights on, all lights went off! Pulled over, switched off, switched on. No rear lights, dash lights, horn. Brake lights work though! Picked the tool up today, dark now but will test all tomorrow. God bless ,❤️👊
I worked on cars for 40 years, 30 for a fleet, and nobody showed me this trick until now, thanks OP. Also I wanna point out one thing and that is, always use a fuse puller tool if you can! Sure needle nose pliers work, sometimes, for some fuses, if you even have space for the jaws to move, which half the time you don't! Plus it is way too easy to mangle a fuse using the needle nose, you might even short something out -
Nice tip. I've been working on the family cars for nearly 60 years, and never thought of, or heard about this technique. I've had a test light in the drawer for decades. A nice simple time saver, with a nice simple explanation. Thanks....I'm subscribing 🙂
Any time I need to find a blown fuze or relay, I just take the fuse block off the car and use my bench top power supply to put 80 amps through it. Now they are all blown and I can't be wrong.
They also make those test lights that will glow green if the probe is on positive. But you can clip the alligator clip to a nail, or small screwdriver, and test wire to see which wire is positive or negative. The test light will glow red if the nail side is positive and the probe side is grounded. Comes in handy for testing polarity on ganged socket plugs in wiring harnesses. Sometimes you can't figure out whick wire is grouded but you know where the positive (power lead) is and you just alligator clip to the positive and probe to find ground.
Want to say thanks for the video, it's the one video that I could understand. You made the video to the point and simple. The way all videos should be.😊
Thank you, always great to brush up on troubleshooting tips. I always keep one of these testers in my car's tool kit. Fuses always seem to blow at the most inconvient times, it's good to know how to quickly find and fix the bad fuse.
Excellent video, great technique ... Q. why do fuses naturally blow with age? (ie: without overcurrent) A. fuses are designed to blow by melting when too hot with overcurrent, hence under normal usage they run warm, so over time the fuse-metal crystalline structure suffers atomic migration which causes physical internal flaws to develop and finally an ultimate failure to conduct electrons (current).
@@dontuno Sure, my explanation covers the fuses that prematurely blow, it's not about all fuses ever made, most stay within their design parameters. It's much the same with incandescent light bulbs, most eventually blow in time but some never do ~ best example is a light bulb somewhere in the US which still works today and has been permanently 'on' for over 100 years.
Thanks for the video ... I have a test light but I never knew about testing fuses this way. I had always pulled them and looked at them with a magnifying glass. Subscribed!
Well known but excellent test procedure.. & worth repeating! However, please fix the start drag volume! I grew up on drag racing, but DON'tT wish to wake everyone in the house when watching a video early in the day!!
I flunked shop class in HS in the 70s; now I'm taking Shop Class 101 on You Tube. I'm starting with the fuse checks because my life has not been very bright overall. :)
This is AMAZING!!! Tbh, you should put some keywords into your content that are for women, auto help for women, etc. Because as a gal, that has never done anything with cars (hush men viewers, I know, I know 😂), you made this so simple!! Now off to see if you have other videos about the other stuff happening lol. 2013 Acura TL - DRL error came on few weeks ago, then suddenly was gone so I dismissed it. Week later - battery completely dead, but when we popped the hood… the accessories came on. (🤦🏼♀️). Now another week or two, and suddenly my low beams don’t work, but high do. Seems to me like it has to be something electrical rather than fuse just based on all that has happened, but just started watching videos 10m ago to see if I can find answers/things to try. SMH - I need a man!!!
How would you if possible test fuses in the rear compartment fuse panel? I have a 2018 Chevy Equinox, I would need to test the back panel and under my steeling wheel. Des the tool come with an extension at all?
For me it's easier to just use a tester and measure the continuity between the two test points, that way you don't have to worry about it getting power. Great video anyway
Tomas, that way works for many, the issues I have with it are: it's a fight for space and hand room when the box is way up under the dash and though few if any fuses do, some circuits operate on 5v and sending the 9V from the continuity tester through that circuit may release the smoke genie or damage componemts. I hope your way continues to work well for you. Thanks for watching and commenting.
I subscribed! Man, no one ever explained about the one-side out fuse. If one side of the fuse is out that means the fuse is bad. That was a question I had and no one else mentioned. See, its little teaching tips like that make all the difference is us DIY guys to increase in knowledge and understanding. Furthermore, it saves us time and money. Another factor was you explained that some fuses are spares and sometimes the key must be turned on to make some fuses illuminate when tested. My question is this. On a 2015 Regal, 2.4L 4 cyl 8 fuses with not light up when I test them. I am searching for the blower motor fuse. I see no such fuse on the fuse or relay schematic located on the underside of the plastic fuse box cover. The blower motor does not come on. How can I locate the appropriate fuse or relay? Could you illustrate how to remove the blower motor on the above-mentioned car and the blower resistor? My 2004 Grand Cherokee, straight 6, 4 cyl blower motor has gone out too. Thanks for you help.
I also have heard of many automotive shops in the northern US states actually snipping fuse output legs on their customers vehicles and turning it back over to them, such a pity...😢 as for myself i am from louisiana, down here folks are raised on a totally different set of standards. Dont really have to worry about that type of thing. Every auto mechanic for a 100 mile radius are small mom and pop business most all of which practice honest morals. If this inflation would ever go on and drift its way up out of here i feel like everything might actually be alright on this end. Yall have a nice evening 😌
@@alive-awake if you snip the output leg of the fuse then when you test on the nipples, you get power on both sides of the fuse but the circuit will not work. You are breaking the circuit on the other side of the test point. The customer has a circuit that doesn't work and someone testing the way you are, picks up no fault. You have to remove the fuse to see the issue.
Great info and instruction, thank you for posting. One question, if I can't find the removal tool how can I get them out? I tried thin nose pliers, but I couldn't get them out. Help advice please.
@@BaldwinsBowtieGarage Ah, good to know. Obviously I wasn't paying close attention to the video as I thought you were connecting the cable to the power terminal on your battery, not the ground. But now that I think about it, that would be stupid. Thanks for setting me straight and the tip.
Thanks for the tip, I’m having the same problem on my 2011 Camry with the headlights and fog lights the fuse lights only lights up on one port thanks a lot 👍🏽💪🏽💪🏽
I have heard these test lights called by another name: "scope on a rope". I had a battery blow up on me. I got covered in acid. Jumped in the shower with my clothes on. Quickly rinsed the acid off my face, hair and exposed skin. Gradually took off my clothes and put them in the washing machine. Then I washed all over with soap. Luckily no damage to my eyes because I flooded them with water so quickly. Now I wear safety glasses anytime I am around battles. My friend is a mechanic. He has had two of them blow up on him.
I use a multimeter. Set it for dc volts....probe across the little metal pips on the fuse. If you get little to no volts, the fuse is good, if you get the battery voltage (11-13 volts) the fuse is bad. Do this with the fuse in-circuit.
You will also get zero v if the circuit is off, like the headlights shown here☺ edit sorry you did mention that, but I was confused so ill leave my comment here too.
That method works well. What I don't like about it is when I'm in an under dash fuse box and I keep needing to turn my head to look at fuse and then dvom, then fuse then dvom. Etc...... so this way works for me. I hope your way continues to work well for you!
There’s no need to check both sides as one side is supply other side is load just check load sides only, same side on every fuse if no power then check supply side,easy faster.
I appreciate your time saving idea, but haven't found the supply side to be the same side of each fuse in all fuse boxes. Regardless, I hope it keeps working for you.
is very informative to "check" a fuse to see if it is blown, but actually "finding" the one that is blown, is going to take way longer than 3.7 seconds hehe
A voltmeter would be better to have than a test light because of its versatility for making other measurements. With a voltmeter, set it to measure DC volts. Place the probes on the test points on the fuse. Polarity doesn't matter. If you measure zero volts, the fuse is good. If you measure 12 volts, the fuse is blown.
While that works for some, it is rather cumbersome while under the dash upside down, looking at fuses, then turn head to look at dvom. To each their own, I hope your way continues to work well for you.
@@BaldwinsBowtieGarage Good point. 👍 Still should have a DVM because if the new fuse blows, then you'll need to measure resistance to ground on either side of that blown fuse.
Great video. Thank you. I have a question…my 2018 Buick Enclave has a dual usb port at the front (underneath the ac controls) that doesn’t work. All the fuse box diagrams don’t point out the fuse that is responsible for this USB port. They talk about the second row and the third row USB ports but none for the front. I can’t even find it on the Buick website and all these youtube videos on replacing fuses. don’t discuss which fuse it is. Any recommendations?
great video! can a bad fuse cause lights like back lights on certain switches on the steering wheel and switches under the radio like the ESC and emergency trinagle switch to stay on causing battery drain? thanks again for great video.
Generally, a bad fuse will not allow power past it. So the fuse itself, won't cause that. But a vehicle may use the information of a system without power to illuminatr warning lights. A parasitic draw test is what you need to do.
It amazed me how many people do not know very simple things. But it's a lot simpler to pull it and see if the link is burned-out. They have been making fuses where you can see the link for years. What you showed was backwards you don't check all your fuses then go to I think you called it the map to see what it goes to. You know something is not working so you go to the fuse diagram and it will say what fuse to check.
Well, normally, I do know what circuit is at fault, and check those fuses first. But many times a car comes into my shop with no manual or diagram on the fuse box cover. I can take 6 minutes to pull up a diagram on shopkey or all data, or in less time than that, I can check them all and move on. Time is money. I hope your way continues to work for you.
@@BaldwinsBowtieGarage Great video and explanations! Would be nice to show the burned link for anyone who hasn't seen it before. Have you ever had a case where the fuse was good, but wasn't making contact on one side? Could be a good time to know the 'look and see' method.
Thank you for the kind words. I have run into that with relays, but never yet on a fuse. I agree I probably should have showed a burned one. Thanks for watching.
Of course... since you have a "map", it's completely little-girl silly to test any fuses for stuff that still works. Only test the fuses that power stuff that doesn't work.
Wow, 68 here and never knew that. I checked my older, next size bigger fuses and they also have access to check without pulling. Not sure but aren't headlights on a thermal breaker and after turning on headlights you're checking running lights? Excellent video, Thanks.
Unless you have a fused 5V reference circuit, that you just sent 9V into with your continuity tester and release the smoke Genie. It's a bad habit to probe circuits for continuity, you should isolate the part being tested first. But, to each his own.
This is a dumb question, but is the cord to the battery on the tester long enough so that you can test the fuses inside the car under the dashboard; or do those inside-the-car fuses require a different type of testing device?
Sir, I have a Tucson 2009 my fuse box has one fuse which connects the right front and rear light, when I replace it it burns out as soon as it clicks, why is that ?
So to test headlight fuse turn headlights on, when headlights are shining, then test fuse. If both sides of the headlight fuse have power, then the headlights are indeed on. 😉
This is one of those instructional vids that should be in the UA-cam Hall of Fame. Excellent!
You made it simple for guys like me....having very less knowledge about these things. Thanks a lot for the help. Life seems easier with guys like you around. 😊
Thank you!
Folks that hate electrical work are probably folks that don't understand it. Thanks for helping us understand it a bit better. 👍
Big facts bro
Yeah no, not really.
I tell you this has been my life for over 60 years 60 years with electricity airplanes cars trucks when I walk out to their car and and just a few minutes to say it is a blown fuse now white I will put a new fuse in and see what happens
electricity in autos is way different than buildings though. i have no issue touching the positive terminal on a battery. touching positive in a home/business .......hell no
Definitely falls under not understanding
Light no sides aren’t turned on or no power
Light both sides full circuit
Light one side only fuse is bad.
You’re 👏
EXCELLENT info. I recently had a blown fuse for my heater blower, and had no idea how to test it. Thank you so much!
Glad it helped
Locate the relevant fuse, do a visual to see the broken inner wire --- ,and if you can't ,just whack a new fuse in , test the circuit that way.
@@ianhill4585 Very good, thank you.
You’re never too old to learn something new says this 68 year old :) good video!
Thank you
Thankyou sir, driving last night and put the dipped headlights on, all lights went off! Pulled over, switched off, switched on. No rear lights, dash lights, horn. Brake lights work though! Picked the tool up today, dark now but will test all tomorrow. God bless ,❤️👊
I worked on cars for 40 years, 30 for a fleet, and nobody showed me this trick until now, thanks OP. Also I wanna point out one thing and that is, always use a fuse puller tool if you can! Sure needle nose pliers work, sometimes, for some fuses, if you even have space for the jaws to move, which half the time you don't! Plus it is way too easy to mangle a fuse using the needle nose, you might even short something out -
Glad to help. Take care!
Nice tip. I've been working on the family cars for nearly 60 years, and never thought of, or heard about this technique. I've had a test light in the drawer for decades. A nice simple time saver, with a nice simple explanation. Thanks....I'm subscribing 🙂
Thank you!
Been working on cars for 60 years and you dont know how to check fuses? 😳
😂
60 years and you are today days old to learn how to test a fuse....😅
Any time I need to find a blown fuze or relay, I just take the fuse block off the car and use my bench top power supply to put 80 amps through it. Now they are all blown and I can't be wrong.
👌
😏
😂😂😂😂
🤣
This is one of the funniest comments I’ve seen in a while
They also make those test lights that will glow green if the probe is on positive. But you can clip the alligator clip to a nail, or small screwdriver, and test wire to see which wire is positive or negative. The test light will glow red if the nail side is positive and the probe side is grounded. Comes in handy for testing polarity on ganged socket plugs in wiring harnesses. Sometimes you can't figure out whick wire is grouded but you know where the positive (power lead) is and you just alligator clip to the positive and probe to find ground.
Sorry I just bought this tester that turns green and red how do I use it ?
Funny it’s mainly only oldies who value lifelong learning. I’m 65 going on 95, now fully subscribed, thank you, brilliantly done.
Not true, I think you just live on a high horse, and can't see past it.
What a silly thing to say
Ugh learning is a part of life for everyone dummy
Old people are gatekeepers.
Not true, I’m a 31 yr old lady and I value learning, I use UA-cam whenever I need to learn something.
Great info and detail. You made it a lot easier to understand. Thank you! 🙏
Thanks for watching!
I've been working on my own vehicles for 14 years and i just found this out, thank you!!!
This is great info. I'm 74 and never knew this. Thank you sir
Want to say thanks for the video, it's the one video that I could understand.
You made the video to the point and simple. The way all videos should be.😊
Thanks!!!
Thank you, always great to brush up on troubleshooting tips. I always keep one of these testers in my car's tool kit. Fuses always seem to blow at the most inconvient times, it's good to know how to quickly find and fix the bad fuse.
Excellent video, great technique ... Q. why do fuses naturally blow with age? (ie: without overcurrent) A. fuses are designed to blow by melting when too hot with overcurrent, hence under normal usage they run warm, so over time the fuse-metal crystalline structure suffers atomic migration which causes physical internal flaws to develop and finally an ultimate failure to conduct electrons (current).
Is that really the case? I see cars that are many, many years old but their fuses are still intact.
@@dontuno Sure, my explanation covers the fuses that prematurely blow, it's not about all fuses ever made, most stay within their design parameters. It's much the same with incandescent light bulbs, most eventually blow in time but some never do ~ best example is a light bulb somewhere in the US which still works today and has been permanently 'on' for over 100 years.
@@dontuno well i mean if you never get blown and you have the ability to blow yourself...
House fuses CAN AND WILL DETERIORATE. I HAVE VERY OLD FUSES FROM 60S SND THEY ARE CORRODED AT LEAST THE TIME DELAY ONES.
This is amazing. I never before read a discussion about fuses proceed down to the actual atoms involved in the electrics...
Sir, nice of you posting this useful video.
I learnt how to check healthiness of fuses ,👍.
Expecting more videos on cars 😊
Thanks for sharing this. I’m working on getting my aging vehicle to last my kids and I another year or two 💙
You got this!
Easily and by far the best instructional vid that I have seen. Congrats and thankyou.
Why wasn't this video 3.7 seconds long?
because of all the google tracking and advertisements
Superb - being a dummy, and my fuse box not being near the battery, i now need to work out how to do this where my fuse box is!
Clip it to some metal
Thanks for this, on visual inspection the fuse looked okay but doing this it showed it had blown. Thanks again.
Thanks for the video ... I have a test light but I never knew about testing fuses this way. I had always pulled them and looked at them with a magnifying glass. Subscribed!
Thanks a bunch!
Thanks for sharing this tip. It worked for me in just a few seconds. Sure beat busting the wrong fuse trying to get it out to check it.
Happy it helped!
Thanks that I watched the video, i solved a huge problem with my van. Keep doing what you are doing.
Well known but excellent test procedure.. & worth repeating!
However, please fix the start drag volume! I grew up on drag racing, but DON'tT wish to wake everyone in the house when watching a video early in the day!!
Noted, thank you.
I flunked shop class in HS in the 70s; now I'm taking Shop Class 101 on You Tube. I'm starting with the fuse checks because my life has not been very bright overall. :)
I'm 64 years old and I just learned this.
Just proves you're never too old to learn! Thanks for watching. Let us know if there's any other instructional videos you'd like to see!
@@BaldwinsBowtieGarage absolutely!!
Pushing 70 here and never knew about the access points! Call me 'unobservant'! Thanks for the info.
Glad to help!
I’m 69 yrs old and this is new to me.
Superb video, great visual demonstration and explanation.
Thank you. I appreciate the kind words.
Agreed
This is AMAZING!!! Tbh, you should put some keywords into your content that are for women, auto help for women, etc. Because as a gal, that has never done anything with cars (hush men viewers, I know, I know 😂), you made this so simple!! Now off to see if you have other videos about the other stuff happening lol.
2013 Acura TL - DRL error came on few weeks ago, then suddenly was gone so I dismissed it. Week later - battery completely dead, but when we popped the hood… the accessories came on. (🤦🏼♀️). Now another week or two, and suddenly my low beams don’t work, but high do. Seems to me like it has to be something electrical rather than fuse just based on all that has happened, but just started watching videos 10m ago to see if I can find answers/things to try. SMH - I need a man!!!
Excellent learning and demonstration……… Bravo mon capitaine……👍
Thank you!
Thanks for your excellent and patient example for checking fuses and test light.
How would you if possible test fuses in the rear compartment fuse panel? I have a 2018 Chevy Equinox, I would need to test the back panel and under my steeling wheel. Des the tool come with an extension at all?
For me it's easier to just use a tester and measure the continuity between the two test points, that way you don't have to worry about it getting power. Great video anyway
Tomas, that way works for many, the issues I have with it are: it's a fight for space and hand room when the box is way up under the dash and though few if any fuses do, some circuits operate on 5v and sending the 9V from the continuity tester through that circuit may release the smoke genie or damage componemts. I hope your way continues to work well for you. Thanks for watching and commenting.
@@BaldwinsBowtieGarage I never thought of that, thanks for the heads up!
Dang I feel stupid. I always took the fuse out to do a visual look. Thanks for the vid bro
I subscribed! Man, no one ever explained about the one-side out fuse. If one side of the fuse is out that means the fuse is bad. That was a question I had and no one else mentioned. See, its little teaching tips like that make all the difference is us DIY guys to increase in knowledge and understanding. Furthermore, it saves us time and money. Another factor was you explained that some fuses are spares and sometimes the key must be turned on to make some fuses illuminate when tested. My question is this. On a 2015 Regal, 2.4L 4 cyl 8 fuses with not light up when I test them. I am searching for the blower motor fuse. I see no such fuse on the fuse or relay schematic located on the underside of the plastic fuse box cover. The blower motor does not come on. How can I locate the appropriate fuse or relay? Could you illustrate how to remove the blower motor on the above-mentioned car and the blower resistor? My 2004 Grand Cherokee, straight 6, 4 cyl blower motor has gone out too. Thanks for you help.
I also have heard of many automotive shops in the northern US states actually snipping fuse output legs on their customers vehicles and turning it back over to them, such a pity...😢 as for myself i am from louisiana, down here folks are raised on a totally different set of standards. Dont really have to worry about that type of thing. Every auto mechanic for a 100 mile radius are small mom and pop business most all of which practice honest morals. If this inflation would ever go on and drift its way up out of here i feel like everything might actually be alright on this end. Yall have a nice evening 😌
what does that mean "snipping fuse output legs on them and turning it back over to them"?
@@alive-awake if you snip the output leg of the fuse then when you test on the nipples, you get power on both sides of the fuse but the circuit will not work. You are breaking the circuit on the other side of the test point. The customer has a circuit that doesn't work and someone testing the way you are, picks up no fault. You have to remove the fuse to see the issue.
Great info and instruction, thank you for posting. One question, if I can't find the removal tool how can I get them out? I tried thin nose pliers, but I couldn't get them out. Help advice please.
The larger fuses with no access to check on top, I'm guessing you have to pull them out to check. Thanks
Well, your supposed to be able to took through the top. If I can't tell easily, I set the ohmmeter up and yest them across the bottom side.
What if your fuse box is under the steering wheel and the battery is under the hood? I guess you need some sort of an extension for the power line.
You can use unpainted metal under the dash as ground.
@@BaldwinsBowtieGarage Ah, good to know. Obviously I wasn't paying close attention to the video as I thought you were connecting the cable to the power terminal on your battery, not the ground. But now that I think about it, that would be stupid. Thanks for setting me straight and the tip.
Ground
2:49 the headlights lighting up when the headlights switch is turned on indicate the good headlights fuse and no extra fuse testing is needed 😂
Thanks for the tip, I’m having the same problem on my 2011 Camry with the headlights and fog lights the fuse lights only lights up on one port thanks a lot 👍🏽💪🏽💪🏽
I have heard these test lights called by another name: "scope on a rope". I had a battery blow up on me. I got covered in acid. Jumped in the shower with my clothes on. Quickly rinsed the acid off my face, hair and exposed skin. Gradually took off my clothes and put them in the washing machine. Then I washed all over with soap. Luckily no damage to my eyes because I flooded them with water so quickly. Now I wear safety glasses anytime I am around battles. My friend is a mechanic. He has had two of them blow up on him.
O yeah....a older man like 30 years ago showed me this.good to know.thought there was a newer way. but great video,!!!
I use a multimeter. Set it for dc volts....probe across the little metal pips on the fuse. If you get little to no volts, the fuse is good, if you get the battery voltage (11-13 volts) the fuse is bad. Do this with the fuse in-circuit.
You will also get zero v if the circuit is off, like the headlights shown here☺ edit sorry you did mention that, but I was confused so ill leave my comment here too.
That method works well. What I don't like about it is when I'm in an under dash fuse box and I keep needing to turn my head to look at fuse and then dvom, then fuse then dvom. Etc...... so this way works for me. I hope your way continues to work well for you!
Thank you for a great tutorial clip on how to check for blown fuses?
That was very interesting! Didn't know this. Best wishes from Germany.
Thank you!
Great never knew anything about fuses until now!
Sure glad it helped. If there's anything else you'd like to see, just drop a comment. Thanks!
as an old dude the test light can be used in many ways for circuit testing as well but i think already know that
This was helpful. Im a complete newbie. Ty
Thankyou Very Much for the tutorial.....I need to troubleshoot my 89 Corvette and need one of these testers.... :)
You're welcome! Good luck with the vette!
i’m trying to figure out if my radio’s fuse is blown i will check it tommorow thanks for the informative video!
Thank you for this video, very useful and straight forward too 😊
There’s no need to check both sides as one side is supply other side is load just check load sides only, same side on every fuse if no power then check supply side,easy faster.
I appreciate your time saving idea, but haven't found the supply side to be the same side of each fuse in all fuse boxes. Regardless, I hope it keeps working for you.
Super instructional. Thank you. Exactly what I needed. Accurate info.
is very informative to "check" a fuse to see if it is blown, but actually "finding" the one that is blown, is going to take way longer than 3.7 seconds hehe
simple trick that I did not know but will for sure use... thankyou for posting.
A voltmeter would be better to have than a test light because of its versatility for making other measurements. With a voltmeter, set it to measure DC volts. Place the probes on the test points on the fuse. Polarity doesn't matter. If you measure zero volts, the fuse is good. If you measure 12 volts, the fuse is blown.
While that works for some, it is rather cumbersome while under the dash upside down, looking at fuses, then turn head to look at dvom. To each their own, I hope your way continues to work well for you.
@@BaldwinsBowtieGarage Good point. 👍 Still should have a DVM because if the new fuse blows, then you'll need to measure resistance to ground on either side of that blown fuse.
Wonderful job! You nailed it.
Thanks
Simple and useful. Simply useful.
Glad you liked it!
Thanks....can you do a video on the fuses with the plastic window..??
Why, you can literally look through the plastic window and visibly see if they are blown
Common sense guy
Take it to a professional
Great video. Thank you. I have a question…my 2018 Buick Enclave has a dual usb port at the front (underneath the ac controls) that doesn’t work. All the fuse box diagrams don’t point out the fuse that is responsible for this USB port. They talk about the second row and the third row USB ports but none for the front. I can’t even find it on the Buick website and all these youtube videos on replacing fuses. don’t discuss which fuse it is. Any recommendations?
Wow, great information and easy to remember. Thanks!!
Do a video on how to find a circuit that drains the battery over night. Thanks...
That was so helpful…thank you!
Thanks for watching.
What about the big fuses? How to check them? They look different from the small fuse.
This video was informative and straight to the point thank you
You are welcome.
ty but do you have to ground on the car battery only? if so, what if tester does not reach fuse in question.. ty haus..
Good job Nick , thanks.
great video! can a bad fuse cause lights like back lights on certain switches on the steering wheel and switches under the radio like the ESC and emergency trinagle switch to stay on causing battery drain? thanks again for great video.
Generally, a bad fuse will not allow power past it. So the fuse itself, won't cause that. But a vehicle may use the information of a system without power to illuminatr warning lights. A parasitic draw test is what you need to do.
How do you test the big 30 amp breakers in a 94 Chevy 2500. Same way?
It amazed me how many people do not know very simple things. But it's a lot simpler to pull it and see if the link is burned-out. They have been making fuses where you can see the link for years. What you showed was backwards you don't check all your fuses then go to I think you called it the map to see what it goes to. You know something is not working so you go to the fuse diagram and it will say what fuse to check.
Well, normally, I do know what circuit is at fault, and check those fuses first. But many times a car comes into my shop with no manual or diagram on the fuse box cover. I can take 6 minutes to pull up a diagram on shopkey or all data, or in less time than that, I can check them all and move on. Time is money. I hope your way continues to work for you.
@@BaldwinsBowtieGarage Great video and explanations! Would be nice to show the burned link for anyone who hasn't seen it before. Have you ever had a case where the fuse was good, but wasn't making contact on one side? Could be a good time to know the 'look and see' method.
@@BaldwinsBowtieGarage Thanks for responding hope you have a great day.
You betcha, you as well.
Thank you for the kind words. I have run into that with relays, but never yet on a fuse. I agree I probably should have showed a burned one. Thanks for watching.
So you wouldn't use a 25 in place of a 20 if it's all you had, and it meant you couldn't opperate your vehicle without it?
How to do it with a multimeter?
Can you get the same thing with a multimeter ?
Thank you. This is a very good refresher video.
Thanks for watching! Let us know if there are other things you'd like us to cover.
@@BaldwinsBowtieGarage Yes, the automotive electrical system would be a great refresher video.
Of course... since you have a "map", it's completely little-girl silly to test any fuses for stuff that still works. Only test the fuses that power stuff that doesn't work.
Can you make a video on how to get the fuse box cover off?
Would you know how to fix a loose blade fuse that won't fit tightly in the fuse box slots?
Wow, 68 here and never knew that. I checked my older, next size bigger fuses and they also have access to check without pulling. Not sure but aren't headlights on a thermal breaker and after turning on headlights you're checking running lights? Excellent video, Thanks.
Thank you!
Watch that left hand in pocket. There's a man who's experienced a high voltage handshake!
Bzzzt! Oh, hello! 😄
You betcha!
Where can I find diagrams that label the fuses for any car
thanks for the help. very helpful content
Thanks for the view!
the fuse box I'm testing is on the passenger side. Where do I clamp for ground, since I'm not near the battery as you did.
Seat bolt, under-dash bracketry, door striker with paint worn off. Any unpainted metal connected to chassis ground.
@@BaldwinsBowtieGarage thanks very much!
Excellent!!! Thanks and GOD bless you.
Well done. Much appreciated!
Thanks
Leave ignition switch OFF. Use a continuity tester, much faster . No continuity equals blown fuse
Unless you have a fused 5V reference circuit, that you just sent 9V into with your continuity tester and release the smoke Genie. It's a bad habit to probe circuits for continuity, you should isolate the part being tested first. But, to each his own.
Thanks for sharing your knowledge ,💐
Thanks for watching!
Thanks sir..very good explanation and easy way to taste fuse..Watching from France..
You are quite welcome. Happy to help. Let us know what else you'd like to see!
This is a dumb question, but is the cord to the battery on the tester long enough so that you can test the fuses inside the car under the dashboard; or do those inside-the-car fuses require a different type of testing device?
You can use any UNPAINTED metal as the ground connection for your test light. Like a bolt under the dash. Good luck and have fun!
Get a multi meter or a test light saves stress
THAT kind of fuse can read good, but go bad when under a load !
Thank you for sharing, you saved me👍 alotta time and money !!
Nice video but I get the owner's manual and see what the fuse location is for what isn't working. Then I remove it and check the fuse.
That is a very good idea! You rock!
What about the M and J type fuses?
Sir, I have a Tucson 2009 my fuse box has one fuse which connects the right front and rear light, when I replace it it burns out as soon as it clicks, why is that ?
So to test headlight fuse turn headlights on, when headlights are shining, then test fuse. If both sides of the headlight fuse have power, then the headlights are indeed on. 😉