amazing advice, everyone else is telling me to solder them together because they need to be jumped through the whole process which is totally wrong. Just got my QX95 flashed from cleanflight to betaflight 3.1.6
Got my QX90 but still can not get it to work, will not flash firmware in cleanflight, so didn't see the need to flash it to betaflight since its suppose to work in cleanflight. For whatever reason I can bind to the spectrum RX but I have no control over anything. The FC is a replacement board as the original board was thought to be faulty, but the replacement looks different in size to the original fc, dont know why. Replacement FC is call SPRacing F3 Evo. Any suggestions?
i only have got 2 of these f3 boards .. one was with eachine eo10s and it needed to be put in dfu mode and the pins literally didnt work and the one that is like this i can flash in betaflight but still wont recognize the usb ..
hello I bought the qx90c quad with F3 evo. I used tweezers on those holes on the side. the instructions are so unclear plus im a noob and it started smoking so I released it and now I have a very small red led lit does this mean ive damaged it?
How do I wire in betaflight osd? I'm trying to use uart 1, cam goes to rx and I have TX going to video in on vtx, do I have to enable uart 1 some kind of way?
Hi! I had a problem with 2 sp racing evo brsuhed, they both worked so good and after a flight the FC just show the red light when I try to fly it, but instead, if i connect it to the computer both leds (blue and red) works perfectly...U KNOW HOW TO REPARE IT?? thanks u so much
How do I arm my quadcopter with flysky i6s & rx2a pro receiver ? When I plug it in the beeper beeps constantly and my transmitter never says it binded & I don’t know how to arm the motors anyway even if I get it to bind
Hi. Good video. a question, you know how to do the flash otherwise connect the card to the pc but it leaves USB NOT RECOGNIZED ..Thanks RESPONDER doubledigitdreams
Thanks so much sharing a much easier and safer way!
Found that the tip of a fingernail file between the "BOOT" bumps will do it too.
amazing advice, everyone else is telling me to solder them together because they need to be jumped through the whole process which is totally wrong. Just got my QX95 flashed from cleanflight to betaflight 3.1.6
Got my QX90 but still can not get it to work, will not flash firmware in cleanflight, so didn't see the need to flash it to betaflight since its suppose to work in cleanflight. For whatever reason I can bind to the spectrum RX but I have no control over anything. The FC is a replacement board as the original board was thought to be faulty, but the replacement looks different in size to the original fc, dont know why. Replacement FC is call SPRacing F3 Evo. Any suggestions?
i only have got 2 of these f3 boards .. one was with eachine eo10s and it needed to be put in dfu mode and the pins literally didnt work and the one that is like this i can flash in betaflight but still wont recognize the usb ..
Gracias por el vídeo. Es justo lo que estaba buscando. Felicitaciones por tu canal
thank you, short and sweet, great info.!!!
Can we connected with camera wifi controlled by the phone
hello I bought the qx90c quad with F3 evo. I used tweezers on those holes on the side. the instructions are so unclear plus im a noob and it started smoking so I released it and now I have a very small red led lit does this mean ive damaged it?
Are you able to just get to DFU mode from the CLI? CLI then type DFU
how to connect a barometer to this board. I am planning to connect bmp280..but I am confused how to do it?
could i use 64bit pc to operate this?
How do I wire in betaflight osd? I'm trying to use uart 1, cam goes to rx and I have TX going to video in on vtx, do I have to enable uart 1 some kind of way?
Using a mac and it says "No response from the bootloader, programming: FAILED" any idea what I can do?
Hi! I had a problem with 2 sp racing evo brsuhed, they both worked so good and after a flight the FC just show the red light when I try to fly it, but instead, if i connect it to the computer both leds (blue and red) works perfectly...U KNOW HOW TO REPARE IT?? thanks u so much
How do I arm my quadcopter with flysky i6s & rx2a pro receiver ? When I plug it in the beeper beeps constantly and my transmitter never says it binded & I don’t know how to arm the motors anyway even if I get it to bind
Is this flight controller 32bit?
Can it work on 64bit?
Hi,
What is the name of quad (or quad kit) in the end of the video?
Hi. Good video. a question, you know how to do the flash otherwise connect the card to the pc but it leaves USB NOT RECOGNIZED ..Thanks
RESPONDER
doubledigitdreams
when i start betaflight i don't have the "DFU" mode activated... what do i need to do ?
My board blinks blue light what does it mean? K i not configurated it its my first time
thank you man
Apa kah bisa fc f3 evo flash di android?
Where did you buy the FC? How much? When ever you do a video you should put links and a description please.
mine dosent have the boot pins
Please tell me how to connect HC-05 bluetooth as receiver to this flight controller ?