7.3 POWERSTROKE EMPTY HPOP RESERVE TANK FIX.................
Вставка
- Опубліковано 5 бер 2022
- 7.3 POWERSTROKE EMPTY RESERVE TANK FOR HPOP HERE IS WHY AND HOW TO REPAIR
#customworks
#hpop
#nooilhpop
#7.3psd
#vgg
#scotty
#eddchina
#donutmedia
#powerstroke
Oil Pump Relief Valve Spring Plug & Seals** For 94.5-03 Ford 7.3L Powerstroke
94.5-03 Ford 7.3L Powerstroke Diesel Oil Pump Relief Valve Spring Plug & Seals
OEM --- Spring, Plug & Seals
SWAG PERFORMACNE - Oil Pump Relief Valve (BALL BEARING)
Fits all 7.3L Powerstroke Diesel Vehicles
F4TZ-6666-KIT
2 YEAR WARRANTY
eBay item number:
255454506207
www.bensound.com
Copyright Disclaimer. Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favor of fair use.
All info presented is for humor no real effort went into actually checking correct or facts . - Авто та транспорт
CHECK VALVE CROWN SOLUTION:
If anyone on here is having issue with the crown removal try this.
Step 1: After removing the cap, spring and ball, remove all the oil using a section tube or twisted paper towel from the drain.
Step 2: place the old ball back in and heat the ball and crown for approximately 1 min. This should provide enough heat for the metal to expand and release from the block.
Step 3: Use a modified pick to remove collar and replace with new one.
I wouldn’t risk it with the chisel method and just using a pick with no heat does not work.
Best of luck and hope this helps someone. Don’t light your truck on fire. 😅
How did you heat the ball and crown?
What kind of torch did you use?
@@Godspln4me and angled map gas torch
Cool thanks!
Wish you had shown how to deal with crown
How do you remove the collar from the block? Thanks
how can I remove the crown to replace it
Hi there I live in Australia and have a 2003 7.3 your videos have been very helpful as not a lot off people know to much about these trucks thanks mate.
Love this info, great channel.
How do you get the crown out of the block??? I can't get my crown out!!! The kit came with a new one
Great Content!
Thankyou
so helpful
Great and to the point ! How about part 2 showing hiw to change the crown, and who you think has most durable parts ? Thanks
1997 7.3 since new.
The crown took off in disassembly but you can pull it out with a hooked style pick screw driver as far as parts OEM Ford
How do I get the crown out. My oil reservoir is running dry I changed the spring and that ball and the o-ring but I could not get the crown out
Another great 7.3 video! You made my purchase less stressful. I feel like I can fix anything on this truck if you just keep making videos. Thanks alot!
The best 7.3 content
Right on
Always a thumbs up
Don't forget about the crown" does nothing with the crown
Have a brand new rebuilt 7.3 motor fuel economy is bad power is bad and when towing no power and you hear a Choo Choo sound and exit gas temperatures are around 1,000 to 1100 thank you and I've been everywhere and they see everything's in specs. Love the videos to good info
Its difficult to diagnose when its not in front of a guy That being said I would doubt its in specs High egt's is screaming a massive air to fuel issue check for exhaust leaks from the heads all the way through the turbo system hot and cold, heck Ive seen air to airs damaged by mechanics pulling motors Ive seen incorrect piston rings or installed wrong check the turbo impeller make sure the injectors are hooked up, it will run on 6 or 7 cylinders and seem just fine Try these idea's
@@CUSTOMWORKS7.3PSD thanks
I so appreciate the no phone in the driveway editing hahaha lol keep the info coming brother thanks for your time
How you get the crown out
brake half the crown with a chisel pull out with a hook screw driver style
Is it removable with hpop in?
I appreciate your videos a lot. I have a major oil leak in the top rear (passenger side) of my 2001 Ford 7.3. I don't see any leaks around the oil lines coming from the HPOP or from the HPOP itself. I tried replacing the oil rail end plug close to the turbo downpipe, but I didn't have enough lead in my arse to get it out. The only video on YT that I've found showing that job also has it already loose. If you ever do a job replacing that, please film it.
Can you get to it with a long extension with a wobble end, then break it loose from the side of the transmission with an impact gun?
So how do you fix the crown?
@east texas sidewinder Please explain how to remove the old seat (crown) below the anti-siphon check ball and reinstall the new crown. I enjoy watching all your videos and learning about the 7.3L. Thanks in advance and have a great day.
our next truck OBS thats coming in after the Cobra project I will show this But for now it is easy to use a long narrow metal chisel and crack one side and pull out with a 90 pick
Well. Im having an extended crank on my 03 with almost 250k. Getting around to replacing parts. New HPOP is in. Wish i saw this video last week when the fuel bowl and HPOP were out of the way. Got new 238/100 injectors to drop in. New alternator, starter, batteries, HPOP lines, IPR, ICP, EBP Sensor. Besides the extended crank i can feel an injector missing for a few minutes after startup until i get on the pedal and build pressure. Fugure its the injector seal going.
Thanks
No problem!
it would be nice if you could show us how to extract the crown.
my oil reserve tank is empty and i will look at that, thanks for showing us how to work on our old 7.3's
narrow cold chisel brake 1/2 of the crown in half pull out with hook style hand puller (like a screw driver) clean evenly tap new one in till you hit the lip in the block. Also would be a good time to replace the LPOP if the drain back ball is kaput your lpop is close to or worn also
@@CUSTOMWORKS7.3PSD thanks, i really appreciate it 👍
Thank you so much for this information. Your videos are professional quality. It shows in your persona as well. Good to know that I have not replaced my lpop for nothing.
Getting that thing back on is infuriating I’m selling my truck before I divthat
Is this the preferred way to also empty the HPOP reserve tank instead of sucking oil out of inspection port at the top? I may be one who still wants to change it out but wanted to avoid sucking it out if I could simply allow it to drain into pan and then reinstall the ball and spring. Do i then need to take top of reserve tank off to refill, or use inspection port to refill? Seems inspection port is going to be messed with no matter what. Thank you.
Great video, and love the actual parts, makes it easy to know what to look for, and fix.
Thanks 👍
@@CUSTOMWORKS7.3PSD
anyway someone can contact you reference a 1995 F350 powerstroke diesel, in a bit of a bind. thanks.
Do I have to remove the high pressure oil pump to get to that check ball spring nut and o-ring?
no only if you want to remove the crown and the crown almost never needs replacement
Dose the crown come out hard or does it just sit under the ball, what holds the crown? Thank you.
The crown is pressed in The demo engine had it removed already in the video In the highest cases there fine its the ball and spring but if you want you take a narrow chisel brake it in half remove with a telescopic magnet and tap the new one in with a bolt I have pulled them out with a hook style screw driver also
@CUSTOMWORKS7.3PSD thank you! Love your videos!!
Why does sludge build up in the HPOP? Clogged screen filter? How do you prevent this besides changing the HPOP oil?
You are so much help. Another thing I over looked. I can get that Ford dealership?
I can't give legal advice But every attorney in my area knows I'm not a person to cross and anyone I take file to court is advised to settle and write that man a check asap and if I where in your situation I wouldn't hesitate
That intro had me dead
How do you get the crown out.
Don't worry about that part LOL
Hello so I was driving and my truck completely died on me and I pulled over and tried to start it again and it just cranks I checked everything and replaced the icp and the camshaft sensor and it still doesn’t start do you have any suggestions of what else it could be
I have spent a considerable amount of time making videos on sensors and how to diagnosis Please go to my video library and scroll through I show how to test sensors , rebuild and several no start video's
Also Clint can you explain why this fails I don’t understand.
On my 03 7.3 I have an intermittent leak which is on the front driver side pretty much pools up about the size of a quarter between the hpop and icp. When I'm looking at the puddle with the truck still running it seems to dry up and lose its shine. I'm going crazy. Figured it was a hpop gasket since all plugs and lines are dry and I can't see under there hpop. But a buddy told me could be this relief valve. What do you think? I don't want to remove the hpop at all. Maybe I get a drop or 2 after a drive which lands in the center of my front diff or dual steering stabalizer mounting plate at the center of the truck.
Will high pressure still build with that ball stuck/bad ?? Like on scanner data?
no scanner data info can deter - man the health of that ball spring / High oil pressure that is abnormal can be a plugged oil cooler or filter poss malfunctioning hpop internal blockage ect
99 7.3. long crank while icp builds, engine starts after icp hits 500-600psi, pressure climbs to 1.5k-2k psi. after 15-20 seconds pressure starts to drop rapidly and engine stalls when pressure drops to ~600psi. Does this sound like a symptom of the drain back valve? I'm not at the vehicle to check, trying to get a plan together.
Have ffd injectors, melling lpop, genuine motorcrap ipr, adrenaline hpop. New quality hp lines. Long crank, turn off, wont turn back on. Reservoir is at like 2 inches from top, which is lower than usual. How do you take out crown?
I also have oil in my valley and leak a lot of oil
ua-cam.com/video/eJem01byfBI/v-deo.html 7.3 POWERSTROKE COMMON AND RARE OIL LEAKS IN VALLEY..........
What if you can't get the crown out, I tried for 3 hours with hooks and picks, it wouldn't budge at all, Thank you in advance!
Hey there Mr clint!! So I put on a new lpop from dieselsite. The thing is my reservoir was going empty afterwards. I saw that there was oil leaking from this part you showing in this video. I unscrewed the plug took out the spring and ball. And I also took the crown out. Put everything new but the thing is I can't screw it back on with all the new things. I wanted to know could it be that the crown has to go bit more down? Or is it suppose to be this hard to screw back on? The plug sits right but don't want to screw. Would appreciate if you can help me out Mr Clint @customworks
I took my motor out of the truck to resealed all the leaking gaskets including the engine oil pan and oil cooler . I installed a new adrenaline hpop and new melting low pressure oil pump . The issue I am having right now is I can’t not get the truck to start. I had filled the reservoir with oil and it started to leak from where the oil filter goes (since the oil filter was not installed at the time ) , I paid no attention to it. But now I’ve notice that I have no oil in the reservoir, I refilled it and when I crank the motor it basically all disappears . Any ideas ? I’m also thinking maybe I have the wrong hpop gasket since their are two versions, I have a 95 ford obs
You should come to Texas and attempt to fix the mist stubborn 99 7.3 in Texas. For views of course.
If this channel builds views and success This is the plan I have several corporate supporters interested but they need to see video's that get views in the 100 plus thousands to millions so If I cant get folks to subscribe and like and share it won't happen
My employee ran my 1994 7.3 out of oil to the point where it just quit. It was down 5 liters .I topped it up and now it still doesn't start.
It has a oil leek and I have invested a lot of time and money chasing it.Replaced all turbo gaskets , oil rail plug at the back of cylinder head ,deleted EBPV. It probably is coming from the HPOP. and I will get to that .For now I need to get it to fire up.Any help? or suggestions
Muy buena su explicación papá y le comento que tengo una powertroke 7.3L año 2001 y tengo un problema con la alta presión de aceite y ya le revisamos y le cambiamos la ipr, icp y aún así pierde la presión de aceite en los rieles que puede estar causando este problema y como se podría solucionar y otra pregunta más y x dnd se descarga la presión de aceite de los rieles al cárter del motor, gracias y esperando su pronta respuesta 🙏.....
El aceite de alta presión se puede perder en el sello de aceite del inyector. Esto se puede verificar con una presión de aire de 120 psi en las tapas de entrada del riel de aceite, como donde se encuentra el icp. Puede quitar el tapón y sostener una pistola de línea de aire con un extremo de goma para obtener un sello hermético y escuche si hay una fuga de aire en cada inyector
Community Verified icon
high pressure oil can be lost at the injector oil seal this can be verified by air pressure of 120psi at the oil rail inlet caps, like where the icp is located You can remove the plug and hold a air line gun with a rubber end to get a tight seal and listen for a air leak at each injector
@@CUSTOMWORKS7.3PSD a ok muchas gracias x su opinión y le pregunto otra cosa, si x casualidad no hay fugas x los inyectores que más quedaría x hacer, gracias y esperando su pronta respuesta 🙏.....
Good verbal blub
I just bought a 2001 7.3 ,, No Start Condition. While cranking 0 psi on icp, Duty cycle 65. If i unplug icp it defaults to 2279 and IPR goes down to 32.03. I have already replaced the IPR. I am leaning towards HPOP. Would you have any other suggestions. I use the FORScan Lite app. BTW your videos are the best on 7.3 engines PERIOD... Also i do have 5 volt reference at the icp plug with the key on. But no check engine light with key on.
If you suspect the HPOP hook up a oil pressure gauge at the ICP see if it builds 500 psi or remove the ICP pack towels and see if it shoots oil out while cranking if its working it will pump many quarts out in a few seconds No CEL light is normal Test the CPS also
@@CUSTOMWORKS7.3PSD much appreciated sir, i will try that. thank you
I told my son about your videos and he also fell in love with them. I was very close to subscribe to your really neat
channel until I saw the video where you whined about a bad china radiator for 15 minutes and now this video
which is incomplete. There are so many videos on you tub that leave you hanging like click bait.Please do not do this.
If the video is to long let a person know it will be part 1 and part 2. You are a fantastic teacher. Please stay as such.
Appreciate the feed back
How do you get the crown out and new one back in? Is it a press fit? Any tricks?
use a hook pick and a chisel like we made mac tool pp8 that we grind ed the end to a chisel//// brake the crown in half then pull out with the pick tool then clean the lip in the block and tap the new one in with a tube or rod we have a 1/2 in rod You will not have much resistance so no hammer needed for install If you do it when the block is still hot it can be pulled out just with a 90 degree pick
So I’m at a lost and I was wondering if you could maybe send me in the right direction. This motor was completely rebuilt. I have low oil pressure at the hpop reservoir causing my dash gauge to bounce once truck is at normal operating temperature. I installed a oil gauge at the oil filter housing and it reads 45psi cold and 7 psi at idle and at normal operating temp. I re-pulled the engine and install a new pickup tube, LPOP, timing cover, oil cooler and replaced both ends on it. I don’t know where else to look other then this pressure relief valve that was reused after engine was rebuilt. The machine shop rebuilt the heads with new injectors cups, installed rebuilt injectors, balance crank, new pistons, cam and all bearings. Anything I’m missing? I’m at a slot on where else to look. The engine is back in and it still has the same pressure after replacing everything. Thanks!
Do you happen to have a part number for the ball spring and plug?
Custom Works
3 weeks ago
94.5-03 Ford 7.3L Powerstroke Diesel Oil Pump Relief Valve Spring Plug & Seals
OEM --- Oil Pump Relief Valve, Spring, Plug & Seals
Fits all 7.3L Powerstroke Diesel Vehicles
F4TZ-6666-KIT
2 YEAR WARRANTY
When breaking the crown, is there a chance that the pieces could fall down into the passage?
as long as you don't move the chisel around no you won't
Thank you for your reply.
Hello Clint Allen, enjoy your info, have a 2002 7.3L with 173K, have replaced ball, spring and cleaned down to the crown but if it sits for 5 to 7 days is hard to start, any longer and have to top off the HPOP reservoir. What is the best way to remove and replace what I am going to call is the seat that the ball seats on and prevents the oil draining back down? Noticed FF-vn9pm above referring to it as the crown and using the chisel method. Can you explain the best and safest way to remove the crown (seat) and how to place the new seat down into the drain/fill hole in order to get it straight and seated so the ball can close it off. I thank you for your time and information. I am new to communicating on the forums so I'll just sign off as Sidewinder!!
I have a 01 PS took to Steeler with a no start they said it needed #8 injector ok
3 weeks later same no start take back now say needs 6 injectors and harness I tell no just put the other 7 in 2weeks later no truck that can't find injectors 2hr later I have them in hand and save my self 1/2 money (genuine Ford) from another dealership they call and say it is blown up
I get there after hours drive it 40 miles runs like new truck
Next day talked to part swapper can't believe that it starts then he says it will knock once it warms up. No knock so I drive it with him same 40 miles 20 ml up mountain 20 down he says must have been air system
While sitting at red light
Like you flip a switch sound's like spark knock blowing white smoke smells like fuel
He says there it's blown up
Turn off restart runs fine no knock no smoke
I drive it 45 ml home on problems next morning crank and crack no start till oil pressure came up then it starts
Drove it to end of street same thing knock white smoke. Turn off restart runs and restarts fine
Next day crank and crank oil psi up it starts ran around town many stops starts fine as I pull into driveway same thing
Took it to another part swapper (not a Steeler ship) wanted to swap same parts as first
Took another swapper more new parts
ECM
FUEL PUMP
MANE COMPUTER
A couple of other sensors
Asked about HPOP they all say no not enough miles on it
158,000
Just the first guy said it was junk
Any ideas
Can you change this out with the timing cover still on?
Yes I do it all the time but one must have patience because your working in a hard area and at a angle
So I’ve got a 1995 F250 with The 7.3 in it which it has the different style high pressure oil pump 96 and up have a different style than what I have in my high pressure oil pump reservoir keeps draining. I put a new high pressure oil pump on it and it still does it any idea what it could be? It does not have the spring with the ball that the video shows I believe from everything I’ve read it is built into the pump but which I have a brand new pump in it and it still does it
All of the 7.3ldi engines have this ball, it is actually not for the purpose of anti-drainback, it is to ensure that lube oil is sent to the bearings before the high pressure oil system gets its oil. however the oil cooler-oil filter adapter does have an antidrainack valve as well as a oil filter bypass valve that will cause your concern as well as worn low pressure oil pump and/or housing.
Got the crown out with the chisel method, but need to chase the threads. Do you know the tap size needed. Appreciate your videos.
No, never had to do that
What's a wobbly? And with the timing cover still on, how tricky is it to get the new one in?
amzn.to/3QOVsgu
Question
I just replaced the hpop and I lost some oil from the reservoir
Should I refill the reservoir and how much ?
yes go and add a quart you cant over fill it a turkey baster works perfect as a funnel
Is this on all years of 7.3 L? What are the other reasons the oil can drain, a worn out LPOP? How do you change out the crown. So many questions
The crown is removed by a narrow chisel hit in same spot break it then pull out with a hook pick then clean ridge in block tap new one on with a rod or pipe so it equally sets into the block ridge //// in rare cases if the lpop is shot and the spring on the pressure ball is worn from heat cycles oil can escape back to pan //// last possibilities the anti drain on the hpop is shot or the seal between the timing cover and block is leaking . These are the most common possibilities
My spring and plug came out but how do you unstick the check ball
telescopic magnet
I tried that…. It’s stuck stuck. Worse case do I pull timing cover off and is it possible for that check ball to fall through downwards? Also, is there a sleeve in that hole that can come out
@@olop2748 Yes You will need to remove the timing cover and no the ball cant fall past the crown I'm thinking the spring broke a tiny bit off and it jambed between the cast and ball and no there is no sleeve The bonus with the age of the motor new timing cover seals and sealant is in order and if you have the funds a new lpop and a oil cooler new seals and o rings
@@CUSTOMWORKS7.3PSD
not ideal but i got one out by using a larger hose and cranking the engine. the oil pressure pushed it out the hose caught it
a peice of gasket from the rocker cover (glow plug+harness) or somthing had made it throght the pump and filter (cold day filter bypassed?) and jamed the ball
over night the res would be drained for a few days i would fill the res hopping it would cut it loose no luck. pain in the but to get to without disassembly but it can be done
Does anyone know what this part he is talking about is called and where to get
94.5-03 Ford 7.3L Powerstroke Diesel Oil Pump Relief Valve Spring Plug & Seals
OEM --- Oil Pump Relief Valve, Spring, Plug & Seals
Fits all 7.3L Powerstroke Diesel Vehicles
F4TZ-6666-KIT
2 YEAR WARRANTY
Does that cause a hard to start condition when it’s been sitting for a few days?
C N, yes this would cause a hard (delayed) start condition. It is an anti-siphon (drain back) check ball as stated in the video, and would cause oil to drain out of the HPOP reservoir when the motor is off. This wouldn't cause a no start condition, only a delayed start. Because, yes, the injectors won't fire until the injection oil pressure is reached. But instead of building oil pressure immediately upon cranking(reservoir has fluid), if the check ball leaks, now you have to wait for oil to be pumped up from the pan. Had this problem with my 94.5 F250.
Hi brother I hope all is going good I was hoping you maybe could make a recommendation I’m looking to replace my hpop lines so I’m not sure where or who to go thur
all of the trucks in the fleet have this /// Ford 7.3 HPOP Lines (99-03) Powerstroke 7.3L High Pressure Oil Pump Lines/Hoses
XTreme Duty- EATON 5800 PSI Hose - Lifetime Warranty CR Performance Premium 99-03 7.3L 7.3 Ford HPOP Lines Hoses
Hose Specs: GENUINE Eaton 5800 PSI WP - 23,200 PSI min Burst & -50F - 260+F Temp Hose
EBAY
eBay item number:
322953503183
@@CUSTOMWORKS7.3PSD thanks brother
I just ordered thanks again and as you would say “YOUR STILL HERE GO HOME”
I changed my LPOP because it was leaking. I went to start the truck back up and it died. I filled up the hpop reservoir and again it died. Is there a correct priming procedure for this LPOP job?
The pump gear needs to be in the correct direction The gears are marked then you need to slather the gears with Lubriplate Motor Assembly Grease Motor Assembly Grease so it can gain suction
@@CUSTOMWORKS7.3PSD thanks for your help, when I first installed it I put synthetic grease. I was able to start it an hour ago but it took all day refilling the hpop through the small port holes with a straw made funnel.
Hello my friend I have a 7.3 2001 model 335000 miles. I drive yesterday fine no problems this morning it was another story a lot of white smoke smell of diesel and no power barely can move 3 to 5 miles an hour. My mechanic cannot figure out what's wrong with that any advice
What are the engine codes ?
@@CUSTOMWORKS7.3PSD it have 5 codes I let you know tomorrow
I had that problem several years ago on my 2001 7.3, it ended up being a cracked piston. Had to do a complete rebuild. An extreme amount of White smoke!!! It missed and had a good amount of blow-by out of the oil fill.
What is the part name. Will I need a new crown and or spring? Thanks in Advance.
I put it in the description for ebay
@@CUSTOMWORKS7.3PSD 👍
Soooo... Now what?
is it under the hpop itself - not the resivor
? The last part of the video shows exactly the location and how to remove.
How does a guy get the crown out?
hook style pick screw driver and a needle nose
Can you do this with hpop still in place?
yes dont remove the crown though ussually the spring and ball is the issue and if the lpop is severly worn that needs replacement as well
@Custom Works yup, have the lpop replacement in hand, just wanted to know if I'm in for another 2 hours of work, I have a custom fuel delivery and hpop removal is a pain, but no fuel bowl so mine should be easy as pulling the hpop reservoir and then getting to this guy!
Its more common to have a bad IDM than anything else if the HPOP has no oil
Why is this?
@@JP-nd8xp diode goes bad in the IDM and short's out. If you know how to fix it cost is only fifty cents but most people pay 800 dollars for new IDM
@@mattvanatti9531