Awesome video… Thanks for posting! I just found a much better way to do this from a friend of mine. Once you get the initial washer out and get past that screen, Just take a very small drill bit and drill a hole in the middle of the plastic thing. Screw a long wood screw into it. Then yank it out by the screw. Took literally 30 seconds
Thanks for the tutorial. Purchased a Kohler a few months ago and the water basically dribbled out, now with the removal of the restrictor, I am having the best shower I've ever had! Thank you🙌🏾🙌🏾🙌🏾🙌🏾
Here’s a tip, if you have a wine cork screw, especially a small one, you can pop it through the hole you made in the restrictor and pop that sucker out. Just tried it and it took me 2 seconds
Tip: Use one of the small flatheads people use for glasses or very small screws - also there are 4 little prongs on the blue piece , bend them flat and inward which gives room to flip the ring out easily
Thank you! I was trying to remove the water saver on my shower head and doing a bit of a hack job. Your video reassured me to persist, and sure enough: beautiful water pressure now!
Thanks! I wasn’t sure if the blue plug was a restrictor (there is a small gasket that blocks outlet holes, too) or part of the shower head. Your video confirmed it for me. After digging at the restrictor for about 2 min, I grabbed my drill and punched a 1/4 hole in the center. After that, it pried out very easily with the screwdriver. Thank you for sharing.
I had a similar looking restrictor on a glacier bay model shower head, just removing the rubber gasket in the middle solved my pressure problem well enough.
No drill, no needle nose pliers. Used a paper clip to pick out the screen gasket, then just a Phillips Head screwdriver to screw a wood screw a little way through the tiny holes near the edge of the blue restrictor. Yank up the screw and the entire restrictor into which it is embedded will pop out with it. Just takes a minute or so once you pick out the gasket screen to get access to he restrictor. Worked on all 3 replacement showerheads I got.
Omg, thank you so much! even though we have a Mainstay 6-setting shower head, it looks just like yours, all the way to the inside of it. Luckily I got the whole thing out! Works amazing! 🥰
Okay, I have the same water restrictor that you do - with the water dribbling sadly from the shower head. However I decided to approach the issue more conservatively. So rather than removing or destroying blessed everything, what I did was start by removing the tiny black rubber O ring from the blue restrictor with a pair of tweezers - which opened a whole series of additional holes underneath. I decided to test the result before going further: I replaced the mesh screen with attached rubber ring - both for aeration and proper distribution of water throughout the shower head - and the result was excellent! As a bonus, there was no need to drag out a drill or even a screwdriver - and no fiddling with silly plumber’s tape.
Yep! We did an experiment after realizing the pressure was too strong after destroying the restrictor in the same Delta shower head. We had another one and instead we just removed the o-ring and it was a nice happy medium I think. Then again, we have very strong water pressure so that's probably what made it too strong haha
I just did exactly the same thing with great results. I didn't have a screen in our for some reason, I may have removed it in the past. Anyway, I came her to .are this same comment and found yours pretty quickly. Glad I realized that this was an alternative approach, before I dug anything out in pieces. I did need some needle nose tweezers to do it and that made it a piece of cake.
The blue piece is NOT the devil, that's the aerator and should be left alone. What affects the water pressure is the black o-ring inside the aerator. Remove that with a paperclip or tiny flathead.
“Gotta wash my butt” is one of the best reasons to remove these things … and there are many, many reasons. Flow restrictors don’t really save water if you have to take a shower 5-10 times as long to feel clean.
Can confirm that removing the black o-ring does the job, no need to struggle with the blue plastic. Just tried it on two different shower heads and pressure/flow massively increased
On some styles of shower heads, they come apart below the water regulator too. If you have one like that you can just pop it out from the bottom side. Usually takes a single tap with a screwdriver and pops right out.
I took a small drill and drilled holes in the blue plastic thing. Then gently did the sides. I was able to remove the whole piece. I also removed the wire mesh in black piece.
Interesting. If your house has decent enough water pressure, simply removing the small o-ring that covers the little holes in the plastic piece would be more than enough. No need to mess with the blue piece. I did this to my Delta shower head and it went from decent to torrential downpour. I put the o-ring back in. I'm on the hunt for an o-ring that exposes maybe just a bit more of the holes than the one that came with the shower head. And to anyone else doing this: I'd recommend putting that mesh screen back in. It's job to to catch any large-ish deposits that might come out of your pipes (i.e lime). It'll end of gunking up your shower head.
Very helpful as I am about to install a new shower head. I cleaned my son's and ruined it by making the holes bigger !! so hopefully the new one will work but just need to get that small metal filter out first and then see if there is a blue or other extra water limiter inside it. here in the UK and in the US should be OUR choice if water is limited or not, not that state's...Pause... done it in seconds - thanks. There was the metal little grill with plastic round the sides (and also in the old one I was removing which had never run fast when last replaced and now I know why) and then in the new one only below that a white plastic thing I did not need to break as I could push through the round hole on other side of the round head thing with a screw driver and it fell right out. Now it is back to our 1990s style speed in there.By the way I have also had to put a shower curtain in (my shower door broke - different room of the house and is such a rare very small and built in with tiles above size I just cannot find a replacement and nor can my plumber. I would still prefer a door but will leave it at that for now.
That's what I'm using but it only clipped off the 4 tips of the blue thing. I used a metal dental pick to get the tiny o-ring out. The o-ring being removed might be enough. It seems like that is what mostly blocks the water from coming through the tiny holes of the restrictor. I'm going to try it with just the o-ring removed in hopes that I don't have to fight with the whole blue piece for an hour.
I personally live in a rental and our water pressure was always s*** and I couldn't get the whole blue thing out but what I did is I used tweezers and I busted the middle out of it just so that it had a big hole I could never get the whole blue thing out but I made sure there was no more plastic and voila works way way better 😘
My apt has water included in the rent and heard that landlords do this to preserve water. Makes no sense really, since the showers will be longer, wont that just add to the same amount of water if it didn’t include the restrictor? Wondering if this changed anything with your rental? I want to give this a try
@@deechacc my water isn't included in my rent but it hasn't changed my water bill lol however (it may be because I have a very old im talking 1990 water hear ) the hot water does run out a bit faster than before hut definitely worth the better pressure lol
Had to do this with my kitchen faucet. I had to remove the entire aerator. The restrictor appears to be fused to it. When I get time I will try to drill some more small holes in it and see if that works. Btw, I was fine with the water pressure but my water lines weren't. Every time I turned on the faucet I was getting MASSIVE water hammer. It shook the entire faucet every time I turned on the water. With that restrictor out of there no hammering at all.
I ended up taking a sharp screw and driving it into the middle of the blue part between the tabs, and then it pulled out a lot easier. My needle nose pliers could not get a good grip on the tabs and kept slipping out. The nice part about using a screw is that it doesn’t rip off tiny plastic parts, like a drill would, but if you take the screw out you can put the restricter back in with slightly higher pressure if you like (we have the in2ition, so the restricter makes the dual spray pointless).
@@IrixGuy don’t feel bad I dug at mine to got the saver out but I left the blue edging in there to! Then my ocd went nuts took a tiny tip of knife the rest popped on out lol
Great video, our shower head must've jarred lose at one time and reset itself cause we had great pressure then all of a sudden it went low flow on us. I took the blue re-stricter out and no it 's working great again, Thnx👍👍👍
All I did was take a nail decorator the one you make designs with that has a rounded ball at the end and poke it in a prior small hole angle and pull. Took 2 seconds!
Awesome video, I have great pressure, an deal with minerals in well water , so I'm constantly dealing with this, Lol mind you I built this house less then 5 yrs ago , so frustrating! Thanks again bud!
Thanks! It’s sad that we have to go to this much effort to feel clean after taking a shower nowadays :(. If you want to take your showering experience to the next level of quality, subscribe to my channel and check out my water softener videos.
Sweet! I may have wasted $30 by buying a high GPM modded one from eBay. I haven't gotten it yet, and got impatient. Glad I found your video. It's much better now and only took 2 mins. I guess I'll put the eBay one in the guest bathroom when it arrives.
Check the link within this video’s description to find the showerhead like I use. A quality showerhead without water flow restriction gets the job done!
I had this exact type or model and I used a small bit or eye glass scre driver to poke a hole in the middle then I used and small allen wrench "L" Shaped tool and angled the turn handle part into holr and then applied leverage and the blue restricter started to come out and used needle nose plyers to pull it the rest of the way out.. I used a small allen wrinch and it did bend its shape from prying. So maybe not too small/thin of a allen wrench.... in this video the guy still leaves most of the blue ring in his shower head for best flow would be to remove it all like I did.
We broke a section of it off and the entire thing fell right on out. OMG the water pressure is amazing. Caution! You will empty your water heater QUICK! Thanks for this science experiment
I got scared when I ran into the blue piece but when I saw the same thing in your video, I decided I was gonna destroy mine too and sure enough, AWESOME water pressure that blows you to the other side of the room. Woo!
Perfect. Been living with low (at least for me) shower pressure from both of our Toto shower heads for too long. Turns out that Toto's shower head flow restrictors are the exact ones as the Delta head you used in your video. Had them both converted in about 30 mins and wow, what a difference. I think the reason you were having a difficult time was your flathead screw driver looked like an older one and the flatheads were rounded of on the ends which wasn't cutting through the plastic. Used the same size driver on a newer one. Cut through the plastic centers like butter. Thanks for the great tip.
If you grab a pair of needlenose players, and gently grasp the edge of the restricter (inside) and once you have grabbed it just yank on it swiftly and hard and the entire assembly should come out. It did for me first try. Just have a firm grip and pull in a straight line very hard. You should see my shower water strength now, I don't pay for water and my flow was already amazing now I have a deep massage thing going on - and if I turn my water on full its almost painful. Thanks for the video. This is a must do for every guy out there having sucky shitty showers that don't massage your back or lower spine!! Thanks again. My shower head is a Peerless Model #76314 (only $16) with 3 modes which maybe will actually work now that there is sustained and good water flow coming out. !!! :_)))
I'll be dog-gone. I didn't even know they still made Peerless. Dang, that was the go-to brand in the 70's and 80's. Well if I don't like this new Delta one (which is plastic, not metal) I'll have to try the Peerless. The one I'm replacing is Moen with only 2 settings (simple and to the point) but he's about to retire so 'in with the new'. lol
I used a drill bit the same size as the hole and held the handle upside down while I drilled so the broken plastic particles would fall down into the waste basket and in 2 minutes I had it done and the water pressure was stronger !...So thank you Mr Butt Washer!!!!......
Congrats! It’s CRAZY how gimped the showerheads right off of the shelf are. If I was in the showerhead manufacturing business, I’d be embarrassed to sell them like that.
@IrixGuy I now have better pressure than my wife's garden sprayer lol. Unbelievable difference. Thank you, I wasn't that kind ripping it out. I had a back up shower head in my Jeep that is going to be returned.
I just helped a friend with a delta hydrorain and either its old and stuck or the restrictor is glued in. The tabs all just broke off, so I removed the oring and drilled a hole in the middle and it works great now
I just took off the little blue tabs in the middle and the little black ring that the tabs held in, and that fixed the water pressure without taking out the who blue piece.
That's what I did. After removing the small black washer, I reinstalled the large black washer and put it back on the shower stem and that increased the pressure by at least 2X. No need to take out the blue plastic piece.
Worked pretty good in mine however I actually wish I didn’t remove the full piece, I realized after I could have just taken a small drill bit and drilled a hole right through the middle, which would increase the pressure, but not the full force of having a giant open hole. Now my tub fills up faster than it can drain which is a bit of a problem lol
@@IrixGuy actually after doing even more research. It’s actually just the rubber o ring that’s restricting the water. Remove that and the pressure will be perfect. No need to jerk around with it for 15 minutes xP
So I removed the restrictor but now my shower is making a high pitched noise. Anyone else have this issue? And how do I fix it? Delta shower head with hose and removable wand. Thank you.
HELPFUL HINT: Only remove the tiny black rubber ring! Not the whole plastic assembly. This instruction was given to me by the manufacturer of the showerhead. They said it coded the warranty but it would increase water pressure. Use a needle or a pin and the ring lifts out easily. Works like a charm and takes only a few seconds!
I took a flat head pocket screwdriver and used it as a punch from the opposite side. Took longer to remove and put the shower head back than it did to remove the part.
Thank you bunches! I freed myself from “the devil” 🤣 mine was much easier than yours. I don’t understand why they would but a restrictor on a handheld. Pressure is the point if the handheld. Plus my home is new construction, so it was good that I took it apart because there was crud in there.
That is awesome! Proper water pressure makes such a difference! New construction? Subscribe and check out my "Dual Shower Head Shower" video. You DEFINITELY need that!
Mine was literally seated in the shower head it was a knock off delta lol. I tried and tried but eventually just slowly melted it away using a lighter torche (great metal band! \m/)using a screwdriver pushed the melted plastic up against the inner walls the threads were half an inch higher so they were not damaged, replaced the gasket and works amazingly 😉
Mine popped right out... But I used a very small flat screwdriver. I put the little screwdriver in the center of that green thing and popped it out that way. Came right out. I think using a very small screwdriver is the best idea
Bro... invest in some needlenose pliers. And you don't need to remove the whole blue piece. Just removing the black o-ring on that blue pc, increases flow.
Friends, before you go drilling, hacking or screw driving that sucker, try using a dental pick to just remove the small black ring seated directly on the restrictor. THAT’S the piece that’s really blocking the water flow. If that doesn’t work (it will!), you can always do the butcher job that ppl are talking about. Mine is a brand new Moen, w 7 settings. Taking that little ring out was a game changer and I didn’t maim or maul the unit.
They change the pipe of our shower & the shower head but I change it with a host. I found white little stones like dirt on the filter of the shower head. It's not a calcium deposit cause they are shape like litte triangle. Whata are those?
That you for caring about the cleanliness of the human butt. I appreciate that. However to really get things cleaned you definitely need a hand held shower massager. So you can power wash everything.. and more
Yup, I actually have a video doing that with a Speakman shower head! That seemed to be a lot easier than this method. Both provided the same result though.
I kinda did that. I took a wood screw and put it under a flame for about 30 seconds then screwed it into to plastic piece. Let it dry and then pulled it out with pliers.
Great tips for removing the flow restrictor which I think is just the rubber o-ring, right? Do you reinstall the screen and small plastic part for a Kohler showerhead? Thanks!
The fact that we even have to do this is infuriating. The fact that they think we're going to save water by restricting the flow is ridiculous. We'll use the same amount of water but the shower will be much longer!!
Another difference is how far you live from the water company!! Depending if you live real far away, your water pressure is not going to be great at times unless you install a very expensive water booster!
So the goal is not to remove the entire water restrictor, only the center. I punched mine repeatedly with a small screwdriver and it was pushed down in one piece. I removed it with cuticle nippers. I have no idea what that tiny O ring would sit on without that round center piece.
![[DONE RIGHT] Fix Shower Head Low Water Pressure | Delta Kohler Moen](http://i.ytimg.com/vi/Xdnej2UgC2s/mqdefault.jpg)
![[DONE RIGHT] Fix Shower Head Low Water Pressure | Delta Kohler Moen](/img/tr.png)
Did this video help? Please consider clicking "THANKS" below the video to support my channel. Thank you!
I used needle nose pliers to grab the little leaf and pulled it out. Took 5 seconds.
what a terrible video on how to it shoukd be how not to
Awesome video… Thanks for posting! I just found a much better way to do this from a friend of mine. Once you get the initial washer out and get past that screen, Just take a very small drill bit and drill a hole in the middle of the plastic thing. Screw a long wood screw into it. Then yank it out by the screw. Took literally 30 seconds
Thanks so much and happy Thanksgiving weekend!
I imagine you could use an easy out as well.
@@chairmanofthebored8684 Awesome! I'm happy to hear that and welcome you to subscribe to my channel!
I'm glad I read the comment section. Thanks
This method worked like a charm. Thanks!
Thanks for the tutorial. Purchased a Kohler a few months ago and the water basically dribbled out, now with the removal of the restrictor, I am having the best shower I've ever had! Thank you🙌🏾🙌🏾🙌🏾🙌🏾
Thank you and please feel free to subscribe to my channel and check out my showerhead videos too!
Here’s a tip, if you have a wine cork screw, especially a small one, you can pop it through the hole you made in the restrictor and pop that sucker out. Just tried it and it took me 2 seconds
Awesome technique! Thanks for sharing!
Wish I’d read comments before I purchased a little ten dollar tool set because I have several cork screws 😂😂😂
Killer! This worked for me! Thank you!!
Did this with a Swiss Army knife, popped it right out
Tip: Use one of the small flatheads people use for glasses or very small screws - also there are 4 little prongs on the blue piece , bend them flat and inward which gives room to flip the ring out easily
Great tips! Thank you for sharing!
Yes, that or a set of picks are the way to go for removal
Thank you! I was trying to remove the water saver on my shower head and doing a bit of a hack job. Your video reassured me to persist, and sure enough: beautiful water pressure now!
Awesome!
Thanks! I wasn’t sure if the blue plug was a restrictor (there is a small gasket that blocks outlet holes, too) or part of the shower head. Your video confirmed it for me. After digging at the restrictor for about 2 min, I grabbed my drill and punched a 1/4 hole in the center. After that, it pried out very easily with the screwdriver. Thank you for sharing.
Thank you!
I JUST WANT TO SAY THANK VERY MUCH FOR THIS VIDEO BRO. DID EXACTLY WHAT U SAID AND NOW MY SHOWER IS CRACKIN LOL
Woohoo that is awesome!
I had a similar looking restrictor on a glacier bay model shower head, just removing the rubber gasket in the middle solved my pressure problem well enough.
Awesome! Water pressure is a must :)
No drill, no needle nose pliers. Used a paper clip to pick out the screen gasket, then just a Phillips Head screwdriver to screw a wood screw a little way through the tiny holes near the edge of the blue restrictor. Yank up the screw and the entire restrictor into which it is embedded will pop out with it. Just takes a minute or so once you pick out the gasket screen to get access to he restrictor. Worked on all 3 replacement showerheads I got.
Great technique!
Did you keep the screen gasket on or off?
@@Joelsmediahere I put the screen gasket back in place.
when he said “that’s the devil” I felt his pain 😂😂😂😂😂
Omg, thank you so much! even though we have a Mainstay 6-setting shower head, it looks just like yours, all the way to the inside of it. Luckily I got the whole thing out! Works amazing! 🥰
You are so welcome!
Okay, I have the same water restrictor that you do - with the water dribbling sadly from the shower head. However I decided to approach the issue more conservatively. So rather than removing or destroying blessed everything, what I did was start by removing the tiny black rubber O ring from the blue restrictor with a pair of tweezers - which opened a whole series of additional holes underneath. I decided to test the result before going further: I replaced the mesh screen with attached rubber ring - both for aeration and proper distribution of water throughout the shower head - and the result was excellent! As a bonus, there was no need to drag out a drill or even a screwdriver - and no fiddling with silly plumber’s tape.
Awesome! Removing the rubber ring only works for some.
Yep! We did an experiment after realizing the pressure was too strong after destroying the restrictor in the same Delta shower head. We had another one and instead we just removed the o-ring and it was a nice happy medium I think. Then again, we have very strong water pressure so that's probably what made it too strong haha
Should always use a bit of plumber's tape.
I just did exactly the same thing with great results. I didn't have a screen in our for some reason, I may have removed it in the past. Anyway, I came her to .are this same comment and found yours pretty quickly. Glad I realized that this was an alternative approach, before I dug anything out in pieces. I did need some needle nose tweezers to do it and that made it a piece of cake.
I removed the rubber ring with a safety pin and got a noticeable difference
The blue piece is NOT the devil, that's the aerator and should be left alone. What affects the water pressure is the black o-ring inside the aerator. Remove that with a paperclip or tiny flathead.
I had to remove both for my water pressure to be acceptable.
“Gotta wash my butt” is one of the best reasons to remove these things … and there are many, many reasons.
Flow restrictors don’t really save water if you have to take a shower 5-10 times as long to feel clean.
Amen!
1/4” drill bit and a nice dewalt drill. Hold it upside down so the plastic does not block the holes in your shower head. Takes about 30 seconds.
Run a screw into the center 1/4 of an inch.. pull the entire thing out with the screw. No drilling, no plastic shreds. 5 seconds.
Can confirm that removing the black o-ring does the job, no need to struggle with the blue plastic. Just tried it on two different shower heads and pressure/flow massively increased
Awesome! That little o-ring is enough for some but every house is different.
Needle nose pliers might have been a better choice to remove the blue thing.
Absolutely.... 5 seconds
Yes. One try for each piece. Done.
On some styles of shower heads, they come apart below the water regulator too. If you have one like that you can just pop it out from the bottom side. Usually takes a single tap with a screwdriver and pops right out.
Thanks. I found removing the rubber o ring was more than adequate for my needs. Hotel like pressure 😊
Sometimes the little rubber ring is all that is needed but every shower is different :)
Thanks for this! I just moved into a new apartment and couldn't even get all the shampoo out of my hair the pressure was so low.
I know the feeling and no problem! Please feel free to subscribe and check out all of my showerhead videos!
I took a small drill and drilled holes in the blue plastic thing. Then gently did the sides. I was able to remove the whole piece. I also removed the wire mesh in black piece.
Excellent technique! #LikeABoss
I used a wooden skewer stick. Popped right off
I stabbed it with a screw driver until it was punctured lol.
thanks, just removing the black rubber seal was good enough for me.
Awesome! It's a matter of water pressure and showerhead....sometimes the rubber ring alone is enough!
That first screen/washer he took out is to keep debris out of the shower head-I'd put that back on if you are on well water...
Interesting. If your house has decent enough water pressure, simply removing the small o-ring that covers the little holes in the plastic piece would be more than enough. No need to mess with the blue piece. I did this to my Delta shower head and it went from decent to torrential downpour. I put the o-ring back in. I'm on the hunt for an o-ring that exposes maybe just a bit more of the holes than the one that came with the shower head.
And to anyone else doing this: I'd recommend putting that mesh screen back in. It's job to to catch any large-ish deposits that might come out of your pipes (i.e lime). It'll end of gunking up your shower head.
Very helpful as I am about to install a new shower head. I cleaned my son's and ruined it by making the holes bigger !! so hopefully the new one will work but just need to get that small metal filter out first and then see if there is a blue or other extra water limiter inside it. here in the UK and in the US should be OUR choice if water is limited or not, not that state's...Pause... done it in seconds - thanks. There was the metal little grill with plastic round the sides (and also in the old one I was removing which had never run fast when last replaced and now I know why) and then in the new one only below that a white plastic thing I did not need to break as I could push through the round hole on other side of the round head thing with a screw driver and it fell right out. Now it is back to our 1990s style speed in there.By the way I have also had to put a shower curtain in (my shower door broke - different room of the house and is such a rare very small and built in with tiles above size I just cannot find a replacement and nor can my plumber. I would still prefer a door but will leave it at that for now.
Thanks my friend
You’re welcome and please subscribe to my channel and check out all of my videos!
I just broke it with a screwdriver and a hammer, turned it upside down, shook and pieces of restrictor fell out. Took me a minute.
Cool
Needle nose pliers are the key! I took care of this in one attempt. FYI.
Needle nose pliers work well! Great technique!
Yep, they pop right out when using needle nose pliers, it took 2 sec.
Exactly what I did just now to this exact same showerhead. Easy peezy, would have gotten IrixGuy back to washing his butt a few minutes quicker.
I'm 3 minutes into the video and you're awesome. Love your humor
I appreciate that you like my humor. Please subscribe and check out my other videos too =)
Needle nose pliers pulled it right out much easier than a screwdriver. Thanks for the tip! No pun intended.
Thank you!
That's what I'm using but it only clipped off the 4 tips of the blue thing. I used a metal dental pick to get the tiny o-ring out. The o-ring being removed might be enough. It seems like that is what mostly blocks the water from coming through the tiny holes of the restrictor. I'm going to try it with just the o-ring removed in hopes that I don't have to fight with the whole blue piece for an hour.
I personally live in a rental and our water pressure was always s*** and I couldn't get the whole blue thing out but what I did is I used tweezers and I busted the middle out of it just so that it had a big hole I could never get the whole blue thing out but I made sure there was no more plastic and voila works way way better 😘
Cool technique! I've done a few with a wood screw and pliers as well.
My apt has water included in the rent and heard that landlords do this to preserve water. Makes no sense really, since the showers will be longer, wont that just add to the same amount of water if it didn’t include the restrictor? Wondering if this changed anything with your rental? I want to give this a try
@@deechacc my water isn't included in my rent but it hasn't changed my water bill lol however (it may be because I have a very old im talking 1990 water hear ) the hot water does run out a bit faster than before hut definitely worth the better pressure lol
Thank you for posting! I have the exact same shower head and performed the same fix (plus a nice soaking on some vinegar). You rock!
Glad it was helpful!
Had to do this with my kitchen faucet. I had to remove the entire aerator. The restrictor appears to be fused to it. When I get time I will try to drill some more small holes in it and see if that works.
Btw, I was fine with the water pressure but my water lines weren't. Every time I turned on the faucet I was getting MASSIVE water hammer. It shook the entire faucet every time I turned on the water. With that restrictor out of there no hammering at all.
Awesome!
I ended up taking a sharp screw and driving it into the middle of the blue part between the tabs, and then it pulled out a lot easier.
My needle nose pliers could not get a good grip on the tabs and kept slipping out.
The nice part about using a screw is that it doesn’t rip off tiny plastic parts, like a drill would, but if you take the screw out you can put the restricter back in with slightly higher pressure if you like (we have the in2ition, so the restricter makes the dual spray pointless).
Cool!
That worked like a charm. Thank you so much!
So happy to have helped! A showerhead with little water flow and little water pressure is useless :)
Thanks for the video, went and took mine out. I would recommend some needle nose pliers, had that thing out in 2 seconds with no trouble
Great tip! Thank you!
@@IrixGuy don’t feel bad I dug at mine to got the saver out but I left the blue edging in there to! Then my ocd went nuts took a tiny tip of knife the rest popped on out lol
Great video, our shower head must've jarred lose at one time and reset itself cause we had great pressure then all of a sudden it went low flow on us. I took the blue re-stricter out and no it 's working great again, Thnx👍👍👍
You're welcome and the internals can gunk up over time too. You should subscribe and check out my water softener videos too!
All I did was take a nail decorator the one you make designs with that has a rounded ball at the end and poke it in a prior small hole angle and pull. Took 2 seconds!
Awesome video, I have great pressure, an deal with minerals in well water , so I'm constantly dealing with this, Lol mind you I built this house less then 5 yrs ago , so frustrating! Thanks again bud!
That is awesome! Thank you very much!
Thank you finally got it out on a kohler maxton!
Woohoo! Congrats! Enjoy the great water pressure =)
Once I got to the restricter, I threaded some floss through it and that let me pull it out pretty easy.
Very cool technique! Thanks for sharing!
I had that thought. How did you get the floss through? Even a curved sewing needle would be too big to get in there.
@@thebewitchinghour831 I bent the end of a floss threader and used that to thread the floss through. It worked pretty well.
Wow! The lesson I learned here was not to use a screw driver to remove the gasket.
I’m happy that you learned something! Be sure to subscribe and check out all of my other videos too!
Needed to see it before, this way we are not sure if it worked or not
It worked wonders for me in all of my showers!
Genius my man
Thanks! It’s sad that we have to go to this much effort to feel clean after taking a shower nowadays :(. If you want to take your showering experience to the next level of quality, subscribe to my channel and check out my water softener videos.
Sweet! I may have wasted $30 by buying a high GPM modded one from eBay. I haven't gotten it yet, and got impatient. Glad I found your video. It's much better now and only took 2 mins. I guess I'll put the eBay one in the guest bathroom when it arrives.
Check the link within this video’s description to find the showerhead like I use. A quality showerhead without water flow restriction gets the job done!
I had this exact type or model and I used a small bit or eye glass scre driver to poke a hole in the middle then I used and small allen wrench "L" Shaped tool and angled the turn handle part into holr and then applied leverage and the blue restricter started to come out and used needle nose plyers to pull it the rest of the way out.. I used a small allen wrinch and it did bend its shape from prying. So maybe not too small/thin of a allen wrench.... in this video the guy still leaves most of the blue ring in his shower head for best flow would be to remove it all like I did.
Interesting technique!
We broke a section of it off and the entire thing fell right on out. OMG the water pressure is amazing. Caution! You will empty your water heater QUICK! Thanks for this science experiment
Woohoo! Sounds like you should check out a tankless water heater :)
Thanks!!! this is an absolute necessity!!
No doubt! Gotta warsh tha butt!
I got scared when I ran into the blue piece but when I saw the same thing in your video, I decided I was gonna destroy mine too and sure enough, AWESOME water pressure that blows you to the other side of the room. Woo!
NO DOUBT! Proper was pressure from a showerhead is so important!
@@IrixGuy gotta clean that butt 🤣
Perfect. Been living with low (at least for me) shower pressure from both of our Toto shower heads for too long. Turns out that Toto's shower head flow restrictors are the exact ones as the Delta head you used in your video. Had them both converted in about 30 mins and wow, what a difference. I think the reason you were having a difficult time was your flathead screw driver looked like an older one and the flatheads were rounded of on the ends which wasn't cutting through the plastic. Used the same size driver on a newer one. Cut through the plastic centers like butter. Thanks for the great tip.
Awesome and thank you for the tip! Water pressure is a great thing, isn't it? =)
Helpful and hilarious. Thanks.
LOL thank you and I’m glad that you enjoyed it! Please subscribe and check out all of my other videos too!
:) " that's the devil" love it!!Thank you for the video. No it is not for patient people but it worked love it
Deeply appreciated and please feel free to subscribe to my channel and check out my other videos too!
"Ask the government first." 🤣🤣🤣
ROFL :)
If you grab a pair of needlenose players, and gently grasp the edge of the restricter (inside) and once you have grabbed it just yank on it swiftly and hard and the entire assembly should come out. It did for me first try. Just have a firm grip and pull in a straight line very hard. You should see my shower water strength now, I don't pay for water and my flow was already amazing now I have a deep massage thing going on - and if I turn my water on full its almost painful. Thanks for the video. This is a must do for every guy out there having sucky shitty showers that don't massage your back or lower spine!! Thanks again. My shower head is a Peerless Model #76314 (only $16) with 3 modes which maybe will actually work now that there is sustained and good water flow coming out. !!! :_)))
I'll be dog-gone. I didn't even know they still made Peerless. Dang, that was the go-to brand in the 70's and 80's. Well if I don't like this new Delta one (which is plastic, not metal) I'll have to try the Peerless. The one I'm replacing is Moen with only 2 settings (simple and to the point) but he's about to retire so 'in with the new'. lol
I used a drill bit the same size as the hole and held the handle upside down while I drilled so the broken plastic particles would fall down into the waste basket and in 2 minutes I had it done and the water pressure was stronger !...So thank you Mr Butt Washer!!!!......
Awesome!
Oh ya, got the whole blue ring out. Love the pressure
Congrats! It’s CRAZY how gimped the showerheads right off of the shelf are. If I was in the showerhead manufacturing business, I’d be embarrassed to sell them like that.
@IrixGuy I now have better pressure than my wife's garden sprayer lol. Unbelievable difference. Thank you, I wasn't that kind ripping it out. I had a back up shower head in my Jeep that is going to be returned.
I just helped a friend with a delta hydrorain and either its old and stuck or the restrictor is glued in. The tabs all just broke off, so I removed the oring and drilled a hole in the middle and it works great now
Great technique and that’s awesome!
This is the solution when the restrictor is fixed
I just took off the little blue tabs in the middle and the little black ring that the tabs held in, and that fixed the water pressure without taking out the who blue piece.
Awesome!
That's what I did. After removing the small black washer, I reinstalled the large black washer and put it back on the shower stem and that increased the pressure by at least 2X. No need to take out the blue plastic piece.
To get that blue piece out all you do is drill a dry wall screw slightly into it and pull it out with a pair of pliers
Thanks! Water pressure is like a fire hose, hits all the right places.
Perfect! Stay clean!
Why did I look around when that doorbell rang !?? LOL
LOL my situational awareness is always up :)
Worked pretty good in mine however I actually wish I didn’t remove the full piece, I realized after I could have just taken a small drill bit and drilled a hole right through the middle, which would increase the pressure, but not the full force of having a giant open hole. Now my tub fills up faster than it can drain which is a bit of a problem lol
Awesome!
@@IrixGuy actually after doing even more research. It’s actually just the rubber o ring that’s restricting the water. Remove that and the pressure will be perfect. No need to jerk around with it for 15 minutes xP
Glad to see you're still posting buddy. Hope you're doing well.
Thanks so much for your viewership and stay tuned for thousands more videos here soon :)
If I was as inept as this dude, I'd hire someone to do it!!
This worked great for me and I only hired myself to do it :)
So I removed the restrictor but now my shower is making a high pitched noise. Anyone else have this issue? And how do I fix it? Delta shower head with hose and removable wand. Thank you.
Thank you!
❤🎉🎉🎉🎉Thank you bruh you made my mom's morning😊
No problem! Please subscribe to my channel and check out all of my shower upgrade videos! 🚿
Thank you very much ! I had the Milwaukee ready to go and found your video. Thank You !!!!!!
Suhweet!!!!!!!!! Enjoy the great shower! 🚿
HELPFUL HINT: Only remove the tiny black rubber ring! Not the whole plastic assembly. This instruction was given to me by the manufacturer of the showerhead. They said it coded the warranty but it would increase water pressure. Use a needle or a pin and the ring lifts out easily. Works like a charm and takes only a few seconds!
For some showerheads of mine, the ring alone was enough but I've achieved the best results by removing the entire thing.
I use some tweezers and they came right out in 5 seconds 😂😂😂
I took a flat head pocket screwdriver and used it as a punch from the opposite side. Took longer to remove and put the shower head back than it did to remove the part.
I poked a hole with a screw driver and then used a cork screw. Got it 2 turns in and pulled it right out
Thank you bunches! I freed myself from “the devil” 🤣 mine was much easier than yours. I don’t understand why they would but a restrictor on a handheld. Pressure is the point if the handheld. Plus my home is new construction, so it was good that I took it apart because there was crud in there.
That is awesome! Proper water pressure makes such a difference! New construction? Subscribe and check out my "Dual Shower Head Shower" video. You DEFINITELY need that!
Mine was literally seated in the shower head it was a knock off delta lol. I tried and tried but eventually just slowly melted it away using a lighter torche (great metal band! \m/)using a screwdriver pushed the melted plastic up against the inner walls the threads were half an inch higher so they were not damaged, replaced the gasket and works amazingly 😉
Amazing technique and that’s great that it worked! BTW, check out my Speakman showerhead videos too! I’ve converted all showers to them.
Yep, did it!! ❤
Awesome!
Needle nose pliers work great!
Good to know!
Mine popped right out... But I used a very small flat screwdriver. I put the little screwdriver in the center of that green thing and popped it out that way. Came right out. I think using a very small screwdriver is the best idea
Great technique!
Lol what are they gonna do come in your house and check your shower heads 😂
LOL as crazy as this world has become, nothing would surprise me!
that is one tight watch band
All of mine are custom-fitted. I leave enough room for my pinkie. It’s never too tight nor too loose.
I live in California so you can imagine the water restrictions. But thanks a million.
Oh man, I'd go nuts if the government tried to control my water pressure. You're welcome!
Bro... invest in some needlenose pliers. And you don't need to remove the whole blue piece. Just removing the black o-ring on that blue pc, increases flow.
That works for some but I needed to remove the whole piece
i took off mine works great now
Perfect!
Had no idea thank you
Neither did I! This made my wife happy because she has the showerhead that she wants. It made me happy because I have strong water pressure :)
Friends, before you go drilling, hacking or screw driving that sucker, try using a dental pick to just remove the small black ring seated directly on the restrictor. THAT’S the piece that’s really blocking the water flow. If that doesn’t work (it will!), you can always do the butcher job that ppl are talking about. Mine is a brand new Moen, w 7 settings. Taking that little ring out was a game changer and I didn’t maim or maul the unit.
The little ring may be enough for some but for me completely removing the water flow restrictor was the fix.
They change the pipe of our shower & the shower head but I change it with a host. I found white little stones like dirt on the filter of the shower head. It's not a calcium deposit cause they are shape like litte triangle. Whata are those?
Sounds like you may have hard water. Subscribe and check out my water softener video.
Thanks bro, my butt will appreciate this later
No doubt!
I took out just the O ring with Pugh damaging the restricter and the pressure change was amazing!
Nothing beats a nice shower! Subscribe and check out my dual shower head video. I’m loving it!
Same. Just remove the small black o-ring.
"Gotta wash mah butt"😂
Gotta keep da butt clean!!!!!
😂😂😂😂😂😂😂😂@@IrixGuy
That you for caring about the cleanliness of the human butt. I appreciate that. However to really get things cleaned you definitely need a hand held shower massager. So you can power wash everything.. and more
I saw someone on amazon say you can drill a screw into the device, then pull the screw with a pair of pliers.
Yup, I actually have a video doing that with a Speakman shower head! That seemed to be a lot easier than this method. Both provided the same result though.
I kinda did that. I took a wood screw and put it under a flame for about 30 seconds then screwed it into to plastic piece. Let it dry and then pulled it out with pliers.
That’s exactly what I did. It worked
Great tips for removing the flow restrictor which I think is just the rubber o-ring, right? Do you reinstall the screen and small plastic part for a Kohler showerhead? Thanks!
It’s a matter of personal preference but I like having all of the restriction removed.
Leatherman bottle opener for the screen, and the pliers for removal of the restrictor, takes like 2 min and no grinding or “digging it out.” 🏈🐒
Great technique!
It used to be simple. The companies gave improve their game on the restrictor. Need to stab at it.
Fantastic
Thank you so much 😀
The fact that we even have to do this is infuriating. The fact that they think we're going to save water by restricting the flow is ridiculous. We'll use the same amount of water but the shower will be much longer!!
I agree.
Using a pick makes it much easier
Check with your local government before messing with your shower head folks😂
ROFL sad times that we’re living in, for sure!
Another difference is how far you live from the water company!! Depending if you live real far away, your water pressure is not going to be great at times unless you install a very expensive water booster!
Very true! Fortunately, removing the water restrictor like this solved my shower water pressure issue but every situation is different!
Needle nose pliers got the job done my boy
Couldn't get the blue piece out had to drill it out.
Like a boss! 🛠️
So the goal is not to remove the entire water restrictor, only the center. I punched mine repeatedly with a small screwdriver and it was pushed down in one piece. I removed it with cuticle nippers. I have no idea what that tiny O ring would sit on without that round center piece.