I just purchased an 870 Police Magnum and started watching vids to familiarize myself. I learned more from your videos than any of the others, from function to disassembly and if I ever wanted to refinish it that's covered too. Also all the parts I'll need to give it that tactical look. Thanks Guys
Hi guys just found this video series and also subscribed! Looking forward to the next one (I know you guys are busy though). It's a fantastic set of videos, you should be very proud of them
I've used most of the cleaners that you have, and the brake cleaners are some of the best, but if you're just cleaning surface crude, oil or grease; mineral spirits are the very best. Denatured alcohol and most others do leave some residue, mineral spirits leaves none what so ever.
Yea just take a picture with your phone and upload it’ll only about 30 seconds we just wanna see the end results you got us 90 percent there , no editing no Hollywood special effects no text no music just pop a picture on the UA-cam channel from your cell lol 😂
Is this the final part? It never showed the parts installation which is the most interesting part. Also didn't that gun already have a non-mim extractor?
I was going to subscribe but the videos are pretty infrequent, which is kind of an understatement. Interesting video two points for those that come in late as myself One put heat on it after you've degreased it and cleaned it. A ceracoater told me that putting The parts in the oven at about 250 for about a half hour Will cause oil down in the pores of the metal to come up. And that really helps with adhesion. Second, for the love of goodness sake, you safety goggles when spring carburetor cleaner. I had my eyeballs stripped of lubricant one time. Learned my lesson.
Well we are back here full time. Consider a sub if you like the content. Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Hello all. Forgive me if this is a stupid question, but... I have a maverick 88 with some rust spots I want to repaint. Is it possible to achieve the same rough surface through sanding the gun with sand paper rather than sand blasting? If so I could just do it myself. Thanks fore any advice!
I've done a Mossberg 500, an AR receiver set and a handgun in Alumahyde II. The results were great on the long guns, but the build up layer junked up the tolerances on the cheap Kel Tec P11. once it fully cures (weeks) it is really hard and has held up for years. Easy to repair as well.
Why you didnt protect the interior of the parts? Didnt plug barrel, cover the interior of the receiver or the forend tube. Tolerances can change if you add a layer of paint over it.
Great vid but what the hell, no part 5? I started watching just to see you install the Trijicon sights, then got interested in some of the info and now find out there's no part 5! Find someone to edit that thing, 3 year delay is insane.
@@Learningfirearms why more "accidents" like these didn't happen in places like Australia and New Zealand when they began banning most firearms is amazing to me!
I'm bummed out. I watched parts one through four and now I can't find the rest of these videos to see how this thing turned out. What a letdown. If anybody knows where to find the rest of these videos please let me know...
Learning Firearms thanks for the response! Ya I looked up on there website as well as other sources that have used allumahide II and most say to oven cure but I don't have the means to stick a fresh painted firearm in the oven without the miss beating me with it. If u say its good without then ill take ur word for it
You never know but we are producing content for another channel now that has take over. We will see if we get some free time. The shotgun is done and has been shooting great.
Video has been shot a long time ago and shotgun is done. Now it’s finding time to edit the video. Problem is paid video stuff and gigs always goes to the front on the line. Sorry man. It is on the list of things to finish but it’s still towards the bottom
So I just finished my pawnshop shotgun from watching this series! Couldnt be happier but before I refurbished the shotgun it was at normal working condition then after the project I had to deeply clwan and polish some internal parts. I'm no gunsmith but I'm somewhat confident in what im doing. Should there be any safety concerns?
Learning Firearms I only polished the revealing part of the bolt to give it a good shine. Everything else I cleaned with degreaser. I did not remove anything from the gun
The joke went above your head. Sorry man. Seriously we wouldn’t do that. Apparently throwing the barrel to camera guy off view and adding a sound effect is pretty hard to imagine.
What the fuck I watch three parts and don’t get to see the finished product I’m so pissed off right now please please please do the final installment I am going to unsubscribe if you don’t upload it
Well this series was a bust. What happened to the carrier spring/extractor and ghost ring sight upgrades? Also the Magpul stock and side saddle shell carrier installation? You guys took WAY too much time leading up this disappointing end. Sorry I tuned in.
Sorry, life and other things took priority. Trevor and I did finish the video, just have to edit it. Unfortunately this channel isn’t my main gig so it was set to the back burner
In your other comment you said we wasted 80% of your time. Either way as you’ve noted we aren’t active on this channel anymore as we’ve move on to another venture. We have part 5 on the to do list. Maybe this spring.
That paint has been curing for 6 years now. Almost ready to assemble.
We did Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
I just purchased an 870 Police Magnum and started watching vids to familiarize myself. I learned more from your videos than any of the others, from function to disassembly and if I ever wanted to refinish it that's covered too. Also all the parts I'll need to give it that tactical look. Thanks Guys
Some say it’s still curing till this day Lmao 😂 #alumahyde #seriously #wheres #part5?
Still tacky to the touch
🤣🤣
@Learning Firearms - So would you say it was a mistake to paint the gun?
Still curing in 2020?
@@LearningfirearmsNot even funny man.
Man, I don't even care about painting a shotgun but I love your videos. Very well paced, simple, and thoughtful. You're doing a great job!
Thank you very much!
What happened to part 5? I want to see the finished product!!
Finally done. Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Nice cliffhanger... This is like ALF.
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Time for part 5 anytime soon?
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Is there a final part I legit need to see it
I agree! Ive been waiting 3 years
Yes they sell it for more than the price of a new one
Where can I find episode 5?
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Thanks for continuing this series, have been looking forward to seeing this completed. I'm out looking for one I can do now.
Looks like you’re sol buddy😂
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
I love this series and these types of DIY videos. I've been waiting a while for the return of the pawn shop shotgun haha
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Been waiting so long for this ep
Totally worth the wait right :-)
I miss these type of videos. I would support a patron account if you made one.
Thanks, that's cool to hear. Not sure if we will make one as most of our new content is for Guns & Tactics but I appreciate the feedback
Hit my line when part 5 is up. Great series though!
Yo. Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Who is still waiting for part 5?
Hell I thought I was crazy. Was looking for part 5 for at least 20 minutes lmao
Me bro
me
Been waiting for literally years for part 5.
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
love your channel very brief and intelligible videos.
Thank you!
Hi guys just found this video series and also subscribed! Looking forward to the next one (I know you guys are busy though). It's a fantastic set of videos, you should be very proud of them
Thanks! Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Did you ever make episode 5 ??
This winter hopefully will be updated the channel with it
Great series! Don't forget to add video 4 to your playlist! ;-)
LMAO. It was a good series. We can figure out the rest. The end left us hanging like breaking bad.
One of these days
Recently came across your videos doing research due to planning on doing the same thing to a 870. Can't wait to see the finished product.
+Daniel Marlin thanks for watching
Just got a maverick 88 from the pawn shop for $130. Going to try this!
Instead of paint, you can now get Duracoat in an aerosol can, just like spray paint. That stuff is tough as nails.
Reminds me of a girl I went out with decades ago... never finished there either.
lol. Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Nice job.
How come you guys haven't put out part five yet?
Justin LaFleur been busy
@@Learningfirearms So.... How about now?
@@drnapalm7605 still busy
@@Learningfirearms now?
SOOOOOOOO about that part 5?? the single most important part of the whole thing....how to put it together and how it looks...
Can’t believe I watched all 4 parts and was ready to see the final finished product and no parts 5?! What the?!!!
I know right! Total BS
Dude it was so good where is part 5?
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
I remove grease from metal by using Sprayaway Glass Cleaner - I use this for repainting motorcycle metal and anything else metal im painting
I've used most of the cleaners that you have, and the brake cleaners are some of the best, but if you're just cleaning surface crude, oil or grease; mineral spirits are the very best. Denatured alcohol and most others do leave some residue, mineral spirits leaves none what so ever.
Yea just take a picture with your phone and upload it’ll only about 30 seconds we just wanna see the end results you got us 90 percent there , no editing no Hollywood special effects no text no music just pop a picture on the UA-cam channel from your cell lol 😂
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
What happened to part5? I'm doing the process already and I need to finish it
Need fulfilled. Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
How about the silver looking shotguns what paint is that
Is this the final part? It never showed the parts installation which is the most interesting part. Also didn't that gun already have a non-mim extractor?
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Where is part 5 ???? I'm so interested and I can't find it :(
+Stillpumping Iron coming soon
When is soon?
@@Attikous maybe this winter
@@Learningfirearms Don't be a tease! You'll never land that second date. ;-)
@@Learningfirearms soon?
I was going to subscribe but the videos are pretty infrequent, which is kind of an understatement. Interesting video two points for those that come in late as myself One put heat on it after you've degreased it and cleaned it. A ceracoater told me that putting The parts in the oven at about 250 for about a half hour Will cause oil down in the pores of the metal to come up. And that really helps with adhesion. Second, for the love of goodness sake, you safety goggles when spring carburetor cleaner. I had my eyeballs stripped of lubricant one time. Learned my lesson.
Well we are back here full time. Consider a sub if you like the content.
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
You got it!
@@Learningfirearms
Hello all. Forgive me if this is a stupid question, but... I have a maverick 88 with some rust spots I want to repaint. Is it possible to achieve the same rough surface through sanding the gun with sand paper rather than sand blasting? If so I could just do it myself. Thanks fore any advice!
No part 5?
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
What happened to the re-assembly video (part 5)? Can't find this , if it exists, on your UA-cam channel.
We’re back Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Legend has it the painted unassembled gun is still hanging to dry
The legend is true
Still tacky to the touch
LMAO. It was a good series. We can figure out the rest. The end left us hanging like breaking bad
Learning Firearms BS
What happened to the rest of the series?
Hasn’t been edited
Thanks interesting if u don't have time 4 part 5 maybe a picture of gun
We have a bunch of footage shot just need to get it edited and uploaded
I've done a Mossberg 500, an AR receiver set and a handgun in Alumahyde II. The results were great on the long guns, but the build up layer junked up the tolerances on the cheap Kel Tec P11. once it fully cures (weeks) it is really hard and has held up for years. Easy to repair as well.
It's amazing paint for sure, I have a couple of other shotguns that have been coated with it and it has been holding up better than duracoat
Wanna see the finished product !!!
So do we! We are going to have an update soon
I need to #5 where is it?
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Why you didnt protect the interior of the parts? Didnt plug barrel, cover the interior of the receiver or the forend tube. Tolerances can change if you add a layer of paint over it.
No we didn’t and it worked out just fine
Great vid but what the hell, no part 5? I started watching just to see you install the Trijicon sights, then got interested in some of the info and now find out there's no part 5! Find someone to edit that thing, 3 year delay is insane.
Coming soon
@@Learningfirearms what the f man?
Part 5?????
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Do u guys keep uploading yet?
Wtf 😒 no end part
Sorry. Better late than never
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
june 14,2020 and still no part 5
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
how much coast if you paint my gun barrel
Find a local cerakote applicator
Blue balls us in part 5. Thanks
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
could you just sand the parts if you cannot access a blaster?
Part 5?
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Just to let you guys know they have moved to Full 30 and are no longer on UA-cam they also post on the GunsandTactics.com UA-cam channel
Our featured video said this a long time ago :-)
Channel Announcement and Exciting News! ua-cam.com/video/qbc_ncorCXw/v-deo.html
wow, this is the least satisfying series ever, I mean, I know what it's going to look like but I want to see it!
yup bummer i know, lost in a tragic boating accident reported to the AFT
@@Learningfirearms why more "accidents" like these didn't happen in places like Australia and New Zealand when they began banning most firearms is amazing to me!
are u guys going to finish this searies befor 2018 ??? just wondering
Most likely
I'm bummed out. I watched parts one through four and now I can't find the rest of these videos to see how this thing turned out. What a letdown. If anybody knows where to find the rest of these videos please let me know...
Maybe soon….
Did you ever finish the shotgun
Yes. Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Currently looking for part 5???
No need to look, hopefully someday but not sure when
I'm doing this same project and I'm using aluma hide but I don't want to bake the finish, is that okay? How long should it cure without baking?
I didn’t oven cure, air cure for at least a week. Follow the directions from brownells they are helpful
Learning Firearms thanks for the response! Ya I looked up on there website as well as other sources that have used allumahide II and most say to oven cure but I don't have the means to stick a fresh painted firearm in the oven without the miss beating me with it. If u say its good without then ill take ur word for it
Learning Firearms another question how many coats do you recommend
must have sold that 155 dollar gun for 800 these days cause ive never seen all this stuff this cheap!!!
That would super suck if we never get to see the final product
Someday we will get around to it.
@@Learningfirearms Please do. I would love to see the final result. :)
have you guys given up on releasing part 5? it's been almost 2 years.
You never know but we are producing content for another channel now that has take over. We will see if we get some free time. The shotgun is done and has been shooting great.
Learning Firearms thought it was still “tacky to the touch” douche bags!
Where's part 5 ?
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Im assuming it still hasnt cured 4 years later
Nope
Finished yet?
As a matter of fact...
Thanks for the other 4, very helpful!!! Are you guys on Patreon? Could be a great way to get paid for the vids if you aren’t.
Dave is the host on another channel now days and all new content is there. Guns & Tactics
11:58 The wife's not going to be very happy!!!
How the hell do you do everything that takes 1 year then ignore the mounting which takes 30 minutes at the extreme maximum? lol
Video has been shot a long time ago and shotgun is done. Now it’s finding time to edit the video. Problem is paid video stuff and gigs always goes to the front on the line. Sorry man. It is on the list of things to finish but it’s still towards the bottom
The absolute bottom of the list...YEARS and you can't seem to find the time (or desire) to get it edited and posted!
What part 5?
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
yea, ep. 5 aint comin chief
Maybe. Maybe not. You never know
Bake that brownells in an oven and it will trump most everything
next episode???
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Damn....so no part five
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Lol got some time now dontcha
I wish, busier than ever on other video projects and still working full time and overtime. “I’m essential”
where the heck is part 5
Here Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
So I just finished my pawnshop shotgun from watching this series! Couldnt be happier but before I refurbished the shotgun it was at normal working condition then after the project I had to deeply clwan and polish some internal parts. I'm no gunsmith but I'm somewhat confident in what im doing. Should there be any safety concerns?
I guess it depends on what you polished and if you removed material from what places.
Learning Firearms I only polished the revealing part of the bolt to give it a good shine. Everything else I cleaned with degreaser. I did not remove anything from the gun
That’s just wrong to not finish the series....
Not wrong any more. Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Where the hell is part 5?
Here. Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
His buddy probably kicked him off the project after throwing the barrel, what a disrespectful thing to do.
The joke went above your head. Sorry man. Seriously we wouldn’t do that. Apparently throwing the barrel to camera guy off view and adding a sound effect is pretty hard to imagine.
What the fuck I watch three parts and don’t get to see the finished product I’m so pissed off right now please please please do the final installment I am going to unsubscribe if you don’t upload it
I just wasted like an hour watching 4 parts to never see a final product. WTF
someday we will post it. On the to do list.
Have yall been demonized
Derrick Shelton moved to another channel. Check out featured video for details
Where is part 5 wtf...lol
Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
still too busy?
Yes
What happened to your channel?
Died from heavy breathing
@@Learningfirearms Did you guys finish that shotgun tho
Wait did you give up on this channel? LMAO
Kyle Davis watch our featured video. We were hired by another channel
LOL, ends his last video with "we dont get paid for this and we are in the red on our videos" and then is never heard from again.
Yup had to prioritize projects. Work. Family life all got in the way. Funny though Trevor and I were just talking about this old gun
And you still haven't done anything about finishing the series... VERY DISAPPOINTING!
Thanks for never making part 5
You’re welcome. Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Well this series was a bust. What happened to the carrier spring/extractor and ghost ring sight upgrades? Also the Magpul stock and side saddle shell carrier installation? You guys took WAY too much time leading up this disappointing end. Sorry I tuned in.
Sorry, life and other things took priority. Trevor and I did finish the video, just have to edit it. Unfortunately this channel isn’t my main gig so it was set to the back burner
Where the hell is episode 5?????? is this a joke?
No joke. Pawnshop Shotgun Part 5 - It's FINALLY DONE! We Hit The Range
ua-cam.com/video/dW6F8DvpeTA/v-deo.html
Almost 2 years and still no conclusion video to this series. Way to leave us hanging, guys. Thumbs down x 4.
SiRHybrid1 Sorry, started making content for a new channel that has taken priority. It’s still on the list :-)
Spray paint ? I thought you were just going to f#ck up a good old shotgun but spray paint? That’s ridiculous.
.
Yeap, what happened to bullet proof bluing a barrel.
Never made a final part. What a joke
Jokes on you. We are making the final part
Published 2 years ago.... no part 5.. are you kidding? I wasted all that time to not even see the finished product. I truly hope you lose subscribers
MikeTheSith200 sorry man.we’ve refunded your viewing fees and know that we’ve lost you forever as a subscriber.
@@Learningfirearms lol i dont care about viewing fees. Just want part 5!
In your other comment you said we wasted 80% of your time. Either way as you’ve noted we aren’t active on this channel anymore as we’ve move on to another venture. We have part 5 on the to do list. Maybe this spring.