The Mirka Abranet Test
Вставка
- Опубліковано 5 вер 2024
- I’m not a huge fan of Abranet, the mesh-backed abrasive from Mirka, but I do see the appeal, so in this video I run the same dust-collection tests from last years orbital sander comparison, to see if the results are dramatically different. Enjoy!
Please use the ‘Like’ button if you liked this video.
Please subscribe if you think you’d like to see more.
Support me directly on Patreon - www.patreon.com/10minuteworkshop
Full list of ‘Stuff I use’ at www.10minutewor...
Connect with me on twitter @10minuteshop
Connect with me on Instagram - 10minuteworkshop
As an Amazon Associate, I earn from qualifying purchases made through these links.
Wherever possible links are to actual products used, but this is not always possible e.g. some products are not available in the US, so something similar has been linked to instead.
Amazon UK - www.amazon.co....
As an eBay Partner Network member, I earn from qualifying purchases made through these links.
eBay UK - bit.ly/Buy_eBay_UK
Used/featured in this video:-
Festool RTS 400 - amzn.to/2x6zGZW (US: amzn.to/2i84yXn)
Bosch GSS 160 Multi - amzn.to/2ikQXw2 (US - only seem to be able to find the GSS 140 palm sander in the US and - ouch! - way more expensive than in the UK : amzn.to/2g1bipC)
Festool Midi extractor - amzn.to/2tCIN3Q (US: amzn.to/2rKNIOx)
Abranet starter kit - amzn.to/2ophnfZ (US: [no starter kit:] amzn.to/2CCmNtf)
Festool Granat abrasive - amzn.to/2A3zU6k (US: amzn.to/2iNk2Rr)
Moldex 6810 in-ear defenders - amzn.to/2sTwQJE (US:amzn.to/2sThGo1)
Photo/video gear
Main camera Panasonic Lumix G80 - amzn.to/2o7uPrx (US - G85: amzn.to/2ouTwJV)
Olympus 12-40 f/2.8 - amzn.to/2sz34Xy (US: amzn.to/2sbYkte)
Second camera Panasonic FZ200 - amzn.to/2pj8p6Z (US: amzn.to/2oYSGJ0)
Rode Videomic Pro - amzn.to/2oTAr5W (US: amzn.to/2oOp54A)
I've enjoyed catching up on this older series. I'm reminded of when I was standing back some inexpertly applied plaster (my fault!) a few years ago using my green Bosch orbital sander. If I'd used a decent sander with a hoover attached, I wouldn't have needed to put a tarp over the furniture and made such a mess to clean up.
Thanks for the vid, I looked to buy the Festool sander/vacuum combo and could not get a decent price. I was at my local Dulux trade counter and Mirka were doing a road show with their combo was at a considerable discount (hundreds of pounds below the green label version). It has been a real workhorse, the Abranet does not clog anywhere near like the standard paper version and I do buy them at a decent price. They last on average three times longer and I don’t throw them away. I’ve done large solid floor areas in my lads salon (Oak) - sand all sorts of furniture. Excellent dust collection was a must. I’m not suggesting it’s better than Festool, for the money it has proved an excellent buy and performer. Kindest regards Mike
Mike S Mike what Mirka sander did you buy? And was it a Ceros or Deros?
I too really like the Mirka sanders and Abranet sand paper/mesh. I have it in 40 grit up to 1200 grit and I get virtually no dust after sanding.
Ron
I have festool and am switching to all mirka. I really feel festool is over rated
i;ve used the mirka deros with abranet sanding discs but you used the the foam backing disc which is used for shaping where as the normal pad saver sands flat
QWERTY7773 Mirka has 2 type of intermediate pad that will extend life of the backing pad. 1 pad saver 2 interface pad. The pad saver is thinner.
I vote for a Dad joke at the start of every video from now on 👍👍
I’ll do my best 😂👍
I’m late to the discussion, this dropped over a year ago (#091) and several months ago (#157). Thank you Peter, for very thorough review & research. I really enjoyed watching the #091 three parts, was on edge of seat by the third episode.
I own Bosch sanders, they are reliable, cost-effective, and get the job done. I love that I can use third party sandpaper with them. Have not yet tried Abranet paper, or drilling out the Bosch bottom plate, thanks for info about Festool pad saver strips.
I also own Festool sanders, they are obviously premium tools. Whenever I am working inside or in a dust-critical situation, I always grab the Festool. When outside, esp with more than one person on the project, we get out the tools, and swap after a while if we can, so ea person gets time on the tools. As expected, opinions are divided. The effect of wood dust on our lungs is long-term. Bill Pentz’ research is food for thought, if not action.
The “is the Festool really worth it?” debate will never subside, nor should it. The wonderful thing about the current tool market is our option to choose from many good choices. Imagine the dire straits if there were only one Tool Company. Of course, the best tool is the best one for you, which will vary from project to project, budget to budget, & clients’ expectations.
Thanks again, you clearly put a lot of time into preparing these videos, they are very informative. I too always appreciate it when I can breathe easily. The dust collection on plastic sheets was an eye-opener. Cheers….
Thanks Rich! 👍👍
Abranet fanboy here I'm afraid. I've been using them for well over 10 years in the automotive industry and I'm sold on them. Yes, they cost more than other types of abrasive but since they almost always last longer than other paper backed products I've used, the initial cost is evened out in the longer run. And I understand your comments about the interface pad. They are made more for sanding over gentle curves, to stop you getting what we call the "50 pence piece" effect, where you can get ridges if you use a harder backing pad. They are not ideal for flat sanding.
I see it has been mentioned already but the pad saver is really what you need in your application. Due to the net nature of Abranet, sanding dust and worn abrasive particles can find their way onto the velcro of your backing pad, causing it to wear and lose its "stickiness" prematurely. The pad saver was introduced to reduce this effect. The velcro on the relatively inexpensive pad saver wears out first, saving the more costly backing pad. They are so thin (basically double sided velcro) that they don't affect the handling of either orbital or random orbit sanders, or indeed hand sanding blocks.
Thanks Andy. I bought a pad saver and an interface pad, and they were both the foam type. Turns out you have to specify ‘pad saver strip’ to get the thin one
Great video as always Peter. It is good of you to take the time to do videos like this comparison since you still work for a living. I might have to give this type of abrasive another look myself as all of my sanders are a mix of brands/types with varying dust collection performance.
Thanks Lucas👍
I follow you faithfully Peter as your 10min. videos give me more useful information than some of the long,long and I do mean long, ones do. Well done.
I couldn't afford those incredibly expensive brand name tools which is why I find your comparisons most helpful.
Cheers Gary! 👍
Look how happy you are with that mesh pun at the start!
I know! Who doesn’t love a dad joke 😂👍
I use arbranet with an LS-130, I don't use any interface pad and I haven't noticed the sander's pad wearing more quickly than usual. Festool also make thinner interface pads. I also find arbranet less likely to leave unwanted marks in finer grits.
My impression was that the main advantage of Abranet wasn't the dust collection, but for the longevity of the sheets compared to traditional sheets.
The normal sheets can "clog" easier, the dust getting stuck in the sheet and making it smoother. With the abrasive being the removable mesh, you can pop it off, blow it out, and continue using that same sheet. You're not constantly popping sheets off and tossing them in the bin. More eco-friendly or the like? Man, I sound like a marketing shill... ;D
Now, whether the longevity and convenience factor offsets the cost is completely another matter, but I've seen woodturners that swear by the stuff :)
Me too, but have to say I’ve never had an issue with clogging on Granat. 👍
Fair enough! This may be one of those instances were it works great better for everything but Festool :D
I do like your comparison videos.
👍
I bought a Bosch GEX 125-1 AE sander last year - its similar to the one you were using in your test but has a 125mm round pad. I find it a nice little sander, effective, handles well and good value. I've tried it with Abranet and found it does improve dust collection over conventional discs, as your test shows. Plus I think I get better performance due to less clogging. So, it works for me!
Appreciate he feedback, thanks! 👍
having used abranet on car bodywork i can say it doesn't clog so doesn't create scratches that ruin your finish just as your nearly finished. They also seem to last a long time.
Abranet is a go to sanding alternative for me, I only use it on wood so that’s my test of credibility 👍👍👍
I use the foam pads to sand non-flat surfaces and profiled timber.
Yeah, watch the follow up vid. I bought the “pad saver” and an “interface pad” and the foam ones were what showed up. “Pad Saver Strip” is the magic phrase, I’ve learned 👍
Thanks for the test, Peter.
Cheers Steve 👍
Good review. Didn't think the pad would affect the Festool so much! Thanks Peter.
Thanks Jim! Turns out there is a thinner pad saver called a "Pad Saver Strip". I bought a "pad saver" and an "Interface pad" and get the foam version both times, sods law. As I say in the vid, I don't think the foam pad affects the dust collection (which was the purpose of this vid after all) but it sure doesn't help the handling!
The Mirka Deros plus Abranet, is a dream combo. Little dust, light, not too much vibration and effective. have tried the lot and I think it is worth every penny. Particularly for the really noticeble reduction in fatigue, which I think subconsciously is the real reason sanding is dreaded, even more than the dust. I bought mine, as an Axminster return. Really recommend.
They’re fine sanders - just wish I could get along with the flappy paddle switch; had to return mine 😕
Thats a shame. Try the new rectangular one, it looks even lighter, and maybe the paddle won't bother you. The plug in versions are easier to use than air powered. The paddle is not so stiff/large.
Dear Peter, thanks for the video. I am making wooden pendants (very small), so I don't have a chance of using power sander. I use hand pads without dust collection. Abranet never clogs. It is faster (I know cause I hand sand) and lasts much longer than all other sandpapers. This is my experience.
Thanks Olcay! I’ve never had a problem with clogging since using Granat tbh, and these tests were really about dust collection more than anything, but appreciate the feedback 👍👍
I just got a Festool Rts400REC and got a Mirka interface pad that fits the Deos , very thin and the Abranet sticks to it like glue and is much better than the thick pad saver that was used in this vid.
If you watch the follow-on video #159, you'll see that I bought a Pad Saver and Interface Pad, and what arrived was identical. What you need is a "Pad saver strip" apparently. 🤷♂️
I’m working my way through your vids Peter, very enjoyable to watch and I’m learning off you, thanks!
Pleasure - appreciate the feedback 👍👍
Check out Autonet by Mirka. Cheaper than Abranet and essentially the same product.
Had never heard of Abernet before, I have some Axminster mesh sanding strips meant for wood turners as they are cooler in use when final sanding a piece spinning quickly on the lathe. They also are quite a bit slower so I guess it depends if you want to save time or your fingertips 😄
👍
I find mesh type sanding abrasives knock spots off of non mesh types when sanding on the lathe. They don't clog as often and both sides are usable. I do use both still. The lower grits from #60-#120 for general sanding and the higher grits #180 - #600 for finishing work
👍
Hi Peter, check out the „Pad Saver“ from Mirka. These are available for Festool hole patterns and only add about 3mm (or less) thickness, thus giving you a much more „conventional feel and control“ for the sander when using Abranet.
Great comparison!
Thanks! It's called a "Pad Saver Strip" apparently. I bought a "pad saver" and an "Interface pad" and get the foam version both times, sods law. As I say in the vid, I don't think the foam pad affects the dust collection (which was the purpose of this vid after all) but it sure doesn't help the handling!
I can‘t speak for the RTS, but I‘ve been using the pad saver on my ETS 150 for years and have no issues in handling. If in doubt, I would say with the hard pad and the pad saver it equals the feel of the medium pad with normal paper, if that helps...
Peter, have you done any testing to determine performance differences between Abranet and non-mesh style sandpapers to demonstrate the effectiveness of Abranet? To my way of thinking, that aspect its sanding performance, which of course would be influenced by how well abrasives facilitate dust-free operations, is much more important.
Additionally, I'd like to see such testing done with the panels in their most common orientation, and that is lying flat on the bench.
Thoughts?
Peter I don't use the pad with my sanders, Festool's and Makita. They also make a thin pad , about 3 mm. B
Thanks! It's called a "Pad Saver Strip" apparently. I bought a "pad saver" and an "Interface pad" and get the foam version both times, sods law. As I say in the vid, I don't think the foam pad affects the dust collection (which was the purpose of this vid after all) but it sure doesn't help the handling!
The biggest problem I found with Abranet was that it lost its grip on the pad much sooner - long before the grit wore down. So you are left with a bunch of (in my case) discs which are usable for hand sanding, but come flying off the orbital sander as soon as you switch on the machine. I tried to talk to an Abranet rep at W16 (NEC Trade show) but he was not interested. I got the feeling that it was a known problem to which they had no answer.
I think this is where the interface pads, or pad saver strips come in. 👍
Yes, I can confirm Peters reply. The Pad saver helps greatly in adding a normal amount of „sticking power“ to the Abranet, It also, as the name implies, keeps the original pads Velcro protected. In addition, it can be used as a minimalist interface pad on normal paper. I‘m not in any way trying to advertise, it‘s just that my personal experience with the pad saver has been really great and I see it as the most important addition to my tools since starting to use Abranet...
Thanks both. Maybe I'll give it a second chance. I spend quite a few hours each week using an orbital sander, so any improvement is welcome.
Long time since I heard laurel &hardy joke.😉😂🤣
I have used abrunet.but i use only for sanding between lacquer coats. Don't use the interface pad.either. but have been happy with results.dont use on fillers etc .Don't find it to good personally.
Good video tho Peter.👍
Nice one Peter, have been curious about this stuff lately and this video seems perfectly timed. I do woodturning and lots of people seem to rave about it, not sure what specific benefits it has in that application though.
Thanks! I think the mesh backing is supposed to reduce heat build-up when using it for turning, but don’t quote me - not a turner ! 👍👍
I invested in a small assorted pack for turning.... not convinced I got my monies worth...
thats an interface pad on that sander rather than a pad saver, pad savers are mm thick. that interface pad is used to sand curved surfaces to help spread the pressure evenly which is maybe why on flat surfaces it tend walk all over the place due to lack of pressure being applied
See Abranet follow-up video. ua-cam.com/video/8lMDfx9O2J4/v-deo.html
Interesting video Peter, thank you. I just can't understand how Festool can justify such high prices. You said the Bosch was almost the same spec. as the Festool yet is almost four times the price.
Thanks Lee. Different strokes, and all that - the Mirka Deos is five times the price, come to that. Though the spec is similar, there are differences; check out the original vids for a more detailed comparison 👍👍
So Bosch + Abranet approaches Festool dust performance.
It’s certainly an improvement - but no match, IMHO. 👍
its not about the dust its the fact that it last forever. i go through 120 grit on a detail sander probably a sheet a day but with mirka i can leave the same sheet on for a week. so its cheaper.
🤷♂️ Horses for courses; every time I’ve used abranet it’s always torn around the edges, so I go through many more sheets of that than, say Granat. And for me it’s all,about the dust collection. 👍
I think your meshing with us Peter ,myself i think the strength of the vac makes a difference and amount of holes in the pad for suction , i use the screening style of sand paper for dry wall mud as it does keep from plugging up and longer life because of it ,otherwise it would look like mesh potato stuck too it ,get it mesh potato ...lol great video Peter
I wouldn't mesh with you Syd 😂
Thanks for that Stanley !!! 😂
😂👍
Peter have you tried the granat net protection pads? They are a lot thinner and therefore less spongy. Maybe the control will be improved?
I haven’t no - if you take a look at the follow on video #159 I was sent the wrong pads - the thinner ones are much better. 👍👍
ok thank you. I will have to watch it.
Hi Peter . Great comparison video...The old ones are the best ones....HA! Will you make to the "Maker Central" at NEC in May?
Thanks Ian! Unfortunately I have a prior commitment that weekend, so while I had every intention of attending, it ain’t gonna happen unless the planets realign somehow. Gutted. 😕
Why do you use a pad, is that a Festool thing?. I use the abronet mesh straight on the sander (Metabo duo) hook loop base. It works great and they last really well.. I would also point out that you did not really test the baroness. The variable was the sander used. I suppose showing last years results go someway towards that but it is hardly a good approach to ensure a valid comparison.
Have you done a video showing your full, normal production, workshop extraction? As your main cutting is the TS55 rather than the Table Saw I recon the dust in your shop is way less than most table saw owners?
The one thing I have noticed in my garage is that the my extraction, a simple shop wet/dry vac, gives out a lot of dust.... this seems to be passing through the vac and back out into the work space. Next step for me is to introduce a cyclone into the system and some air filtration system. I will have a search for your Festool Shop Vac videos... I know that their equipment is expensive but if it works then the price is irrelevant!
Thanks Richard! I talked about it in general terms in video 066 Workshop tour ua-cam.com/video/Ce_gMwIQQsk/v-deo.html, and in more detail when it broke - and was repaired - more recently in video 370 My Problem with Festool, ua-cam.com/video/WhDSe6wG4_c/v-deo.html HTH. P
Great review. The Fusstool is better but will cost you. The amount of holes in the pad seems to be the factor. I thought the Abranet would have made a bigger difference and helped the Bosch. Maybe try a piece of Mirka pad saver as a backer.
Call me crazy but i just bought a Mirka Deros 5” palm sander for $600. Incredible sander. Completely dustless, variable speed, quiet and low vibration, soft start....Amazing. If you look at the Mirka pad it has about 40 holes that all interconnect to the suction. The reviews were so good i had to try it. Replaced an old Portercable 5” screamer. Went from one extreme to the other. My lungs wish these sanders existed 25 years ago. The cost is absurd. Cant understand how a palm sander costs as much as my Hitachi slide miter? Fusstool’s pricing is absurd also but they are pushing all the other tool makers to improve their products. Fusstool will have to adjust pricing eventually or loose market share.
Thanks! Mirka Deos is more expensive than the Festool RS400, just FYI. The Deros is a fine sander, just wish I could get along with the flappy paddle switch - had to return mine 😕
I am a bit confused about this. Why would anyone care about how much dust is left behind? I assumed that abranet was better because it cut faster and lasted longer - these are the only two things i care about with sanding. Dust remains is the last thing i could care about.
Effective dust collection is one of the main selling points of mesh-backed abrasives. Showing what’s left behind is a simple visualisation of how effective - or not - the abrasive is in that regard. And you should start to car about dust collection - your lungs will thank you, and so will your clients. 👍
@@10MinuteWorkshop I simply wear masks when I do any operation that generates dust. I also cannot afford a dust extraction system like the one on the video. So it is a meaningless benefit. Does the Abranet product last longer? Or give a better finish? Or is it quicker? If none of those three then that is fine - but it means it is not a product that has any benefits to me.
I get others might for some reason want a tiny bit less dust, just does not mean anything to me.
I have a Mirka pad saver for my Rotex125, to use abranet on that machine. It’s not got the stupid squishy bit on it. Just Velcro on both sides.... pretty sure they do them for the RTS too - disclaimer, I’m not a fan of a tamer either, brillant2 and granat all the way I’m both my Rolex and my RTS !
Thanks Richard. I bought both a pad saver and an interface pad, and they were both the squishy foam. Turns out I should have searched for ‘Pad saver strip’ which is exactly as you describe. I’ve ordered one to check it out 👍👍
Peter Millard I’m pretty sure Festool have their own version now, since they brought out “granatnet”, I suspect it’s simply rebranded AbranetAce as you still net the same pad saver...
Really? I haven’t tried it, but I’ll check it out , thanks! 👍
Peter Millard has everything you need: www.festool.co.uk/campaigns/landing-page/granat-net
Interestingly, they’ve also released 125mm now too!
Abranet is what the woodturners use I had plenty of this for my lathe easy to bend etc.
How do you do extraction I heard some type of industrial vacuum in the video do you have flexi pipes over the workshop or some type of tube ducting?
Make plenty of dust here I have a Henry Vacuum looking at rigging this up to suck it up somehow. Regards Tony
Hi Tony. I’ve heard from a few woodturners who are fans - the mesh backing makes for ‘cooler running’ I think?? WRT extraction I have an old Festool CTL 22 vacuum under the main bench and I run the hose up and over the bench to a boom arm that reaches the main areas pretty well - I talk about it in a bit more detail in my shop tour video. I have another smaller extractor attached to the mitre saw, that also does duty on the bandsaw. 👍👍
great video regardin abranet we use it it is good but expensive there is a alternative either screwfix or toolstation do it the roll is about 3m long x 115mm wide costs about six pounds tried looking it up but cant find it at present i think it is a screwefix product worth looking into
I’ll check it out, thanks! 👍
after my first comment its toolstation that do it its called prodec 5m x 115mm 120# only brilliant stuff wont clog and it costs £5.69 per roll in the book page 32 must try it
Cheers Lawrence 👍👍
Very interesting video Peter, I don't think I will bother trying the Abranet,this video is pretty convincing.I see you still have the Aldi bandsaw, no date on collection yet?
I think if you already have a sander with good dust collection, then Abranet isn't going to improve it, no. But don't take my word for it - invest 50p in a sheet 😆 No, the bandsaw winner is in Scotland but one of their children is tasked with collection - no word on when exactly yet, though.
Peter Millard It might be some time then with the weather in Scotland as bad as it is at present. You will have to start charging storage 🤣
Hi Peter any reason why you can't use abranet direct to the festool rts400 as you did with bosch sander. Regards David
Hi David. Yes, Festool use their own version of hook and loop that doesn't play nicely with other abrasives generally, but especially Abranet, unfortunately; the sheets just don't stick well. 🤷♂
Thanks Peter good to know
Hi Peter, another great video thanks! Just out of interest, I notice you work with MDF quite a lot and I was just wondering if you use an M class dust extractor for this? I know the Festool CTL26 is meant to have the same filter as the CTM26 but without a few of the extras, so I was considering going down this route. However, just wanted an idea of what the pros use. Thanks again for all the great content!
Hi Daniel, and thanks! I use regular CTL extractors; as far as I can tell the only difference between the L and M class Festools is the warning you get with the M class when the extractor bag is full enough to restrict the airflow. But of course, please do your own research before making a significant purchase! I seem to remember a detailed thread on Festool Owners Group forum about this exact issue - might be worth getting on over there and searching it out?? 👍👍
Thanks for the info Peter, it's a great help. I'll be sure to check that out!
Festool now make a new interface pad to accommodate their new mesh abrasives ( bet you they're made by Abranet), that looks as if it won't interfere as much
Turns out here’s a thin Abranet one as well, a ‘pad saver strip’ 👍
Hi Peter, great videos :-) Can I ask you which pad saver strip you would recommend for the Bosch? Thanks...
Thanks! I don't think you need one for the Bosch tbh, but of the ones that are available I'd recommend the 'pad saver strip' and not the pad saver, or interface pad, as they're the squishy foam ones - see video #159 for more. 👍
Peter, do you prefer the rectangular orbital sander over the circular random orbital sander? I haven't seen you use a random orbital on the channel yet and am in the market for a new Festool sander and am torn between the two. Any suggestions for which would be best overall or a do it all type sander?
No, I use random orbital sanders a lot, but sometimes a plain orbital is better suited for the job, though often that’s as much due to size and weight, as the actual sanding pattern. A 150mm random orbital with a 5mm stroke (eg ETS 150/5) will cover an awful lot of situations, from relatively aggressive paint-stripping to fine finishing. A small orbital (eg RTS400) will cover pretty much all other situations, aside from detail sanding in tight spaces. One area I would be a bit cautious about is a smaller (125mm) RO because they typically have a smaller stroke (~2mm) so are really meant for fine finishing only. As always though, the piece you’re working on will dictate what you need to use; I’m okimg on some small side tables with the leg and shelf section are only 36mm square, and I’ve used a 150mm RO on the initial prep, and the RTS400 for fine finishing and paintwork prep. That all have a place, and a role to play. HTH P
Peter Millard, Thanks for the response. Keep up the good work in and out of the work shop. Really enjoy your videos from across the pond.
Hi I recently bought the ETSC125 cordless sander and am wondering if anyone else has encountered an issue with the Velcro pad: I’m finding that the sanding discs (both Granat and Abranet) are not held well enough by the Velcro pad and so move and curl up at the edges- very disappointed with this. Any advice or comment gratefully received thanks.
You shouldn’t be getting any curling at the edges with Festool abrasives on a Festool sander. The Abranet issue is widely known, and needs an interface pad to stick to the proprietary Festool hook & loop, but I’ve always found Granat to stick very well. Assuming I t’s the original Festool backing pad, I’d contact the dealer and return it for replacement as that isn’t right at all. Let me know how you get on. 👍👍
@@10MinuteWorkshop Great thanks for that: I will contact the dealer. Is an interface pad the same as a protection pad?
I read that it is heat which kills the hook and loop, possibly due to how I am having to use the sander atm without dust extraction (and with 80 grit).
Also; sorry to go on!; am I at a disadvantage since a ‘hard’ pad is not available for this particular sander?
Sorry, Mirka do two - an interface pad, and a pad saver. It's the pad saver that you want - the interface pad is a ~5mm thick foam disc that doesn't do anyone any favours, the pad saver is just a thin (~1mm) disc with hook & loop on each side. And yes, you really need to use dust extraction, as the airflow helps keep the pad cool. I've never used anything other than the (medium??) pads that come with the sanders, they're generally a good all-rounder. 👍 👍
@@10MinuteWorkshop many thanks 🙏
Try Autonet cheaper then Abranet same stuff
Thanks, I’ll give it a try. 👍
Nice video, I tried Abranet for sanding my woodturning bowls, didn't find it produced a better finish and if being truthful found i got more catches with it than normal grit paper
Agree - it's not for everyone, or everything, but certainly has a place for some 👍
Abranet seems to cost around 3 times as much around here, so I wonder if it lasts 3 times as long?
After watching Katz-Moses video on sandpaper, I bought 3M cubitron for about half the price of a pack of Abranet. Sanding 2 entire flights of stairs, one with paper, the other with nets, it feels like nets compared to even the highest quality paper disks do last at least 2-3 times as long.
You essentially turned a abranet video into a comparison between Bosch and festool which is pointless as festool is gonna be king on performance no matter what its compared too ,you needed to use either Bosch or festool and use standard sand paper and the mesh for comparison.
Whats your experience of clogging? I bought some JCB branded mesh abrasive recently (because I saw it in the shop and thought I would give it a go) and in my limited use of it it does appear to clog less/be easier to unclog than normal sanding sheets.
Have to confess, I've never had an issue with clogging when using Granat. I think the dust collection helps keep the abrasive cool, which reduces it significantly. 👍
I have used the mesh based stuff on my mouse sander which doesn't have any dust collection (I know I should have realised when I purchased it!) and it appears to clog a lot less than normal abrasive. Plus when it does you can just peal it off and blow it out. I noticed that a commenter below has mentioned something similar.
I guess the moral of the story is, only buy sanders with good dust collection designs and it makes life better all round! :)
Can you try put RUPES new range of sanders please
Rupes aren’t widely available here - if I can get my hands on one I’ll do my best! 👍
Peter Millard in the process of buying one from Decorative Agents on Facebook just been released 👍
One more vote for dad jokes lol
😂👍
Think I will stick to pad sandpaper.
Joke was worth using 👍😄
Totally! 😆😂👍
What was the joke , Mr Hardy?
😂👍
Interface pad-contoured surfaces! Pad saver-flat surfaces! Jokes-brilliantly 3rd rate!🤣🤣🤣🤣🤣🤣👌👌👌👌👌👌
Thanks! It's called a "Pad Saver Strip" apparently. I bought a "pad saver" and an "Interface pad" and got the foam version both times, sods law. As I say in the vid, I don't think the foam pad affects the dust collection (which was the purpose of this vid after all) but it sure doesn't help the handling! Hey, and those jokes don't write themselves 😂
Exactly - the thickness/softness of the foam is to aid contour sanding, not useful for sanding flat surfaces. Try the standard pad saver, and perhaps gravitate towards Abranet Ace, which is supposed to be more durable. The pad savers are necessary, as otherwise the virtue of the abranet becomes a flaw, as the sanding base gets worn out too rapidly, making for a much more expensive replacement.
Given extraction is one of the more important criteria, I'm wondering why no manufacturer has designed the fixed sanding pad with hundreds of smaller holes to maximise the virtue of the Abranet/mesh style of abrasive? Presumably some straight forward calculations could be made to design one which optimised the performance of the mesh? Or is this a new improved line of sanders, that's just round the corner? :-)
I must confess, I do on occasion waste 10 minutes or more in my garage/workshop.
Me too! 😆👍👍