well i had to put the limit switch back on for the camera and this gives so much troubels is there a options to use the camera without the limit swiich
4:00 please help, i have bought sculpfun s30 pro and sculpfun cam. i followed this step by step instalation tutorial and got problem that the maximum area collides with the engraving machine frame, and there is an annoying sound when it hits the right frame. how to fix it?
3:48 Modify the parameters in the red box， The working size of S30Pro in the video is 383 * 375, which is incorrect. In fact, it is 381 * 375. If the position of your limit switch is different from what I installed, then you need to measure it yourself.
Bonjour besoin d'aide . J'ai une sculpfun s30 ultra 22 watt. Du coup ma zone de travail c'est quoi que je doit mettre ? 600*600 , 400 * 400 ou bien la même qu'il mette dans la vidéo ? Cordialement
Hi, i hope you can help me out. I have a S30 Ultra, wich is a 600x600mm working area and i am trying to instal my CAM500 and it captures the 400x400mm middle top of my honeycumb board but when i am about to do the camera alignment and i frame the area before i engrave, the laser frames the middle of my honeycumb board and not the top 400x400 area that the camera captures. How can i finish the installation of my camera with this problem?. Could you post a video with the callibration of the CAM500 on a laser with bigger working area that 400x400mm? Thanks for your time.
yes same problem here. It says suits S30 Ultra so i purchased one. No it doesn't adjust properly to work area so am going to have to modify the mounting to make it suitable. should have saved money and made my own cheaper.
@peterbraid2975 I thought it could be a problem, and surely enough it was. ... I'm using a quickly assembled extension with a few planks and will test if that works. I should have known that even though @SCULPFUNreal say it is compatible that it would extend beyond 400x400. I bought it for the elegance, now look at my Frankesteincamera ...
@@user-jh1mq2ih2u kinda. It's dumb that they didn't make it just like 10cm bigger. Haven't made a proper extension. But it holds, I wouldn't recommend. If you have to diy it anyway, one could as well just buy a high quality webcam and make a custom fixture. What's important is that the camera's position to the frame doesn't change. Otherwise it's not super accurate.
Is there any option to calibrate and align this camera using MacBook. system camera option not coming for us. even I tried to use different focus mode but still not able to calibrate. Please reply to me. If any option is there try to upload a video for installation using MacBook. I looking for responses.
1- You must have a L-Shape feet to bolt and mount to the workbench 2- You must have spaces (aluminum) around the honeycomb + L-shape to also fasten the honeycomb. Either you provide the L-Shapes braces + screws or replace the legs for everyone who wants this (extra cost).. Otherwise, it will not be accurate when its moved! 3- What about the enclosure? It will be blocked.. So you should also have a solution to use the camera with it too... It will be easier to add the camera to the enclosure by changing the height and location of the frame braces. 4- Add LED for better picture and capture options 5- You may need to suggest and add USB Bridge because some old notebooks have only 2 USBs- Mouse, Laser, and now Camera!
You don't need to fix the engraving machine. After the camera completes the Calibrate Camera Alignment, the engraving machine can be moved. You need to ensure that the camera is not moved in its position on the engraving machine
@@SCULPFUNReal Actually, the camera + camera 2020 bars are screwed to the frame very very well, and after I off the machine and- the next day, the camera is not aligned!
I bought this camera months ago and watched every video especially this one, spent many hours many days calibrating and trying absolutely everything in detail in this video and still can't get accuracy. The company won't ever reply to me so I cannot recommend this product.
it will work with any size. Just the usable area of the camera is about 400x400. You increase it (mount the camera higher) but the quality will decrease accordingly. Use a bed size of what ever you want and take the area of 400x400 as camera enabled area.
Do I have to recalibrate the camera in Lightburn everytime I work on a worpiece with different height? Or after first calibration just adjust the camera height to 330mm from camera to surface workpiece?
hi, i bought a sculpfun 500 and i mounted on AREA extention kit S30 (950*410). i installed the camere near the mother board, but i see the image in the middle of the cutting area and not in the bottom posizion (0,0). how can i do to move the image from the middle are cutting versus the origin? tx in advance
It looks like it's possible to also use a regular digital camera/web cam- would I be correct to assume this? I do plan to get this kit here once I have a bit of extra Money, it looks way more convenient than any home solution I would put together. Also, does this cover the full size of the expansion kit work area (900x900mm)? If not can it be custom extended to sit higher and give a wider viewing area?
I just acquired a S30 Ultra-22W Laser and the CAM500, the laser has a 600x600 mm work area, but guess what ? the camera frame-arm is just 35cm, so when i home the laser to 0,0 limit the center of the working area can´t be reached by the camera arm so it´s imposible to configure it. You should specify that this camera is only for smaller frames or replace to all the owners of the camera with frames bigger a new arm or refund our money. Oh and if you use MAC OS you can´t configure it because there isn´t any app that can move the bright or contrast of the camera and display grids as the video (believe me i just downloaded 10 different app and no one has this functions) and even if any app has the functions the width of the arm would never reach the center of the working area. Awful
The camera functionality is a software issues when it comes to control settings like brightness and darkness not the camera itself and yes they should disclose that it won’t work on the ultra models as far detecting the whole bed
A ver si alguien me puede ayudar. No hay manera de poder calibrar bien la cámara. Algún video explicado en español, por favor, porque la última actualización del lighburn la 1.7 me hizo un desastre y me desprogramó todos los parámetros que tenía. Ahora no tengo manera de volver a hacer que la camara funcione correctamente y ya me estoy desesperando un poco la verdad. muchas gracias de antemano un saludo
hello..im using imac and im stuck at minute 4:47, i cant find where the system camera if using mac facetime wont show the camera grid please..anyone can help me
@5:18 the camera is already at the center after some adjustments...but soon after we are instructed to adjust the height to within 325-330mm wich brings the camera out of the center... what gives?
Where is the tutorial to make it work on a 600x600 machine? I'm stuck in this
I've bought a cam500 and I need to install it on my laser. Thanks for this tutorial, I'll try 🙂🙏🏻
I hope to manage 😅
well i had to put the limit switch back on for the camera and this gives so much troubels is there a options to use the camera without the limit swiich
wow, every second of this video is worth watching, I loved how it can be used to make timelapse😊
😘😘😘
After switching the resolution in the camera settings, you can use Ctrl+C, and there is no need to manually input in the later settings
4:00 please help, i have bought sculpfun s30 pro and sculpfun cam. i followed this step by step instalation tutorial and got problem that
the maximum area collides with the engraving machine frame, and there is an annoying sound when it hits the right frame. how to fix it?
3:48 Modify the parameters in the red box， The working size of S30Pro in the video is 383 * 375, which is incorrect. In fact, it is 381 * 375. If the position of your limit switch is different from what I installed, then you need to measure it yourself.
Looks great. Will be watching it again once I get one
😉
@@SCULPFUNReal I'd love to be an influencer for Sculpfun. I applied but never heard anything back
Bonjour besoin d'aide . J'ai une sculpfun s30 ultra 22 watt. Du coup ma zone de travail c'est quoi que je doit mettre ? 600*600 , 400 * 400 ou bien la même qu'il mette dans la vidéo ? Cordialement
Bonjour mon ami, je vis la même chose, as-tu trouvé la réponse à cette question ?
@@luisgodinoibanez4021 merhaba. bu sorun için bir çözüm buldunuz mu?
Hi, i hope you can help me out. I have a S30 Ultra, wich is a 600x600mm working area and i am trying to instal my CAM500 and it captures the 400x400mm middle top of my honeycumb board but when i am about to do the camera alignment and i frame the area before i engrave, the laser frames the middle of my honeycumb board and not the top 400x400 area that the camera captures. How can i finish the installation of my camera with this problem?. Could you post a video with the callibration of the CAM500 on a laser with bigger working area that 400x400mm? Thanks for your time.
yes same problem here. It says suits S30 Ultra so i purchased one. No it doesn't adjust properly to work area so am going to have to modify the mounting to make it suitable. should have saved money and made my own cheaper.
@peterbraid2975 I thought it could be a problem, and surely enough it was. ... I'm using a quickly assembled extension with a few planks and will test if that works. I should have known that even though @SCULPFUNreal say it is compatible that it would extend beyond 400x400. I bought it for the elegance, now look at my Frankesteincamera ...
@@jonwtrdid it work?
@@user-jh1mq2ih2u kinda. It's dumb that they didn't make it just like 10cm bigger. Haven't made a proper extension. But it holds, I wouldn't recommend. If you have to diy it anyway, one could as well just buy a high quality webcam and make a custom fixture. What's important is that the camera's position to the frame doesn't change. Otherwise it's not super accurate.
Is there any option to calibrate and align this camera using MacBook. system camera option not coming for us. even I tried to use different focus mode but still not able to calibrate. Please reply to me. If any option is there try to upload a video for installation using MacBook. I looking for responses.
Man I solved with Obs studio on Mac last night 😎
@@danienteaqualcosa how????
How do I enable the crosshair in the camera as you do? is there a different program for this other than Lightburn?
in any chance to setup your camera with the lasers without limit switch?
how come nobody says anything about the enclosure for the laser? most of us use laser enclosures and the camera won't fit inside
04:47
how does it work with a macbook?
Man I solved with Obs studio on Mac last night 😎
do we really need to buy the limit switch? is this not appicable to s9 without the limit switch?
Where do i find the camera software for mac
got the same problem..please anyone help us
Men I solved with Obs studio on Mac last night 😎
Bit of a shame you have to instal limit switches. Or, really, the S9 should come with them.
But still, I've got one on pre-order.
Agreed… these are a PITA in their own. I’m still figuring out altogether…
I have the extended work do u all have a video to help me please I wanna buy this asap
1- You must have a L-Shape feet to bolt and mount to the workbench
2- You must have spaces (aluminum) around the honeycomb + L-shape to also fasten the honeycomb.
Either you provide the L-Shapes braces + screws or replace the legs for everyone who wants this (extra cost)..
Otherwise, it will not be accurate when its moved!
3- What about the enclosure? It will be blocked.. So you should also have a solution to use the camera with it too...
It will be easier to add the camera to the enclosure by changing the height and location of the frame braces.
4- Add LED for better picture and capture options
5- You may need to suggest and add USB Bridge because some old notebooks have only 2 USBs- Mouse, Laser, and now Camera!
You don't need to fix the engraving machine. After the camera completes the Calibrate Camera Alignment, the engraving machine can be moved. You need to ensure that the camera is not moved in its position on the engraving machine
3- build your own enclusure at the right height for the camera, like me 😉
@@SCULPFUNReal Actually, the camera + camera 2020 bars are screwed to the frame very very well, and after I off the machine and- the next day, the camera is not aligned!
Is there a version of this device planned that works with the extended work area?
Sorry maybe no.
I bought this camera months ago and watched every video especially this one, spent many hours many days calibrating and trying absolutely everything in detail in this video and still can't get accuracy. The company won't ever reply to me so I cannot recommend this product.
Graba desfasado?
O cual es el problema?
Espero que muy pronto,salga para poder usar con el kit de expansión...
it will work with any size. Just the usable area of the camera is about 400x400. You increase it (mount the camera higher) but the quality will decrease accordingly. Use a bed size of what ever you want and take the area of 400x400 as camera enabled area.
Do I have to recalibrate the camera in Lightburn everytime I work on a worpiece with different height? Or after first calibration just adjust the camera height to 330mm from camera to surface workpiece?
If the height difference is large, try to readjust the focus.
hi,
i bought a sculpfun 500 and i mounted on AREA extention kit S30 (950*410). i installed the camere near the mother board, but i see the image in the middle of the cutting area and not in the bottom posizion (0,0). how can i do to move the image from the middle are cutting versus the origin? tx in advance
Did you find an option?
Salve, io ho un macbook pro come faccio ad impostare la griglia sulla cam. Sono bloccato su questo passaggio. Grazie
Please send email to our after-sales, we need to send you a picture:support@sculpfun.com
Ciao Dario, non sono riuscito neanche io con una griglia vera e propria, ma ho risolto con Obs studio ieri sera 😎
Saludos estos videos de configuración por favor los pueden subtitular al español gracias
Hola, no puedo configurarlo con la sculpfun s30 ultra 600*600 graba mas abajo de donde muestra la imagen.... Alguin logró solucionarlo??
En la ventana de control de cámara calibra el desfase moviendo el eje de x o eje y
Help not working voor ultra 30 600x600?
Hello friend, I am going through the same thing, have you found the solution for this?
Si funciona pero solo enfoca 400x400
Where is the camera software in windows?
It looks like it's possible to also use a regular digital camera/web cam- would I be correct to assume this? I do plan to get this kit here once I have a bit of extra Money, it looks way more convenient than any home solution I would put together.
Also, does this cover the full size of the expansion kit work area (900x900mm)? If not can it be custom extended to sit higher and give a wider viewing area?
I just acquired a S30 Ultra-22W Laser and the CAM500, the laser has a 600x600 mm work area, but guess what ? the camera frame-arm is just 35cm, so when i home the laser to 0,0 limit the center of the working area can´t be reached by the camera arm so it´s imposible to configure it. You should specify that this camera is only for smaller frames or replace to all the owners of the camera with frames bigger a new arm or refund our money. Oh and if you use MAC OS you can´t configure it because there isn´t any app that can move the bright or contrast of the camera and display grids as the video (believe me i just downloaded 10 different app and no one has this functions) and even if any app has the functions the width of the arm would never reach the center of the working area. Awful
Thanks for the information. I was going to make the same mistakes as you. Buy the ultra 33w and use it with a mac 😮💨
Did you got any other option for alignment using MacBook???
The camera functionality is a software issues when it comes to control settings like brightness and darkness not the camera itself and yes they should disclose that it won’t work on the ultra models as far detecting the whole bed
That's meen iOS,and Mac is suck😂
@@andreyaleks3970 no, the cam & software sucks.
only think i get is patern not found trying more then 50 times now
Is it possible to use this on s30 600X600 frame ?
Si pero solo puedes usar 400x400
A ver si alguien me puede ayudar. No hay manera de poder calibrar bien la cámara. Algún video explicado en español, por favor, porque la última actualización del lighburn la 1.7 me hizo un desastre y me desprogramó todos los parámetros que tenía. Ahora no tengo manera de volver a hacer que la camara funcione correctamente y ya me estoy desesperando un poco la verdad. muchas gracias de antemano un saludo
wow excellent video very well explained😮
😆😆😆
hello..im using imac and im stuck at minute 4:47, i cant find where the system camera
if using mac facetime wont show the camera grid
please..anyone can help me
Man I solved with Obs studio on Mac last night 😎
No limit Switch for the S30 - Ultra Series? Help.
S30 - Ultra Series has limit switch in the package. Don't worry.
Very informative video and great camera!
Thank you!!
Hola, alguien sabe cómo configurar la cam 500 para un área del la sculp fun de 600x600mm ?
Por más que lo intento, es imposible
Gracias
Tengo el mismo problema. lograste solucionarlo?
Lo máximo que enfoca en 400x400
@5:18 the camera is already at the center after some adjustments...but soon after we are instructed to adjust the height to within 325-330mm wich brings the camera out of the center... what gives?
Супер! Настройка жуть какая долгая, но девайс классный )
😊😘
Kinda scary to see hhe amount of unanswered comments here, i guess I'll just have to order one and see whats up so people can get some answers 😅
I can't get the capture right
where are you stuck？
@@SCULPFUNReal it's not talking the capture,
I wish I was more tech savvy
for all Mac users: I've probably solved with OBS studio and McGiver Mode 😎
Ok, I solved. The camera is working
Hola ¿con qué opción habilitaste el gris en OBS studio?
Hello which option did you use to enable the grids in OBS studio?
@@oscareduardolunabarber22 no grid in obs, I draw the center in the center of the laptop’s lcd, with some paper tape on it
Too fast for me.
Way too fast, had to rewatch 100 times, not to mention he put the camera upside down
❤🎉
Nice video.. just to fast..
Check it here: diode-laser-wiki.com/documentation/extras/#Camera_usage
👍👍👍👍
Eine der schlechtesten Erklärungen auf UA-cam
Terrible instructions
Why is the language in Windows 11 Must be in Chinese, I can't read (when opening the camera in Windows)