Five Essential Classic Accessories Colorado XT Mods
Вставка
- Опубліковано 6 лип 2024
- These are the modification I made to my fishing pontoon to make it more comfortable to fish from.
PARTS LIST:
=======================================
Casting Deck
6) 1-1/4" PVC Tees
2) 1-1\4" x 18-1/4" PVC Pipe
1) 1-1/4" x 16" PVC Pipe
8) 1-1/4" x 1-1/2" PVC Pipe (for spacers)
2) 1-1/4" x 3" PVC Pipe (four coupling)
2) 1-3/8" x 18-1/4" Wood Dowel
1) 1-3/8" x 26-1/8" Wood Dowel
4) 6" x 24" Decking
6) 1/4" x 3-1/2" Carriage Bolts
6) 1/4" Nylon Stop Nuts
6) 1/4" Flat Washers
Seat
4) 5/16" x 1-1/2" Carriage Bolts
4) 5/16" Tee Handle Nuts
4) 5/16" Flat Washers
4) 1/4" x 3/4" Carriage Bolts
4) 1/4" Tee Handle Nuts
4) 1/4" Flat Washers
Battery Box
4) 5/16" x 1-1/2" Carriage Bolts
4) 5/16" Flat Washers
4) 5/16" Nylon Stop Nuts
Transom
1) 20-1/2" x 5" x 1-1/2" Wood for Transom
4) 3/8" x 3-1/2" Carriage Bolts
4) 3/8" Nylon Stop Nuts
4) 3/8" Flat Washers
Wheels
1) 1" x 1" x 12" Steel Tubing
1) 3/8" x 3-1/2" Hex Bolt
1) 3/8" Nylon Stop Nut
1) 3/8" Flat Washer
1) 3-1/2" D-Pin
This is the most professional upgrade video I've seen. Well done.
I can't begin to tell you how proud and impressed l am with you your brother Bill.
Dude! I had my boat for about 5 yrs and this by far is the most in-depth true diy upgrade video for this boat to date. Where were you when I needed to mount my rod holders lol. Great work my man. I'm going to change out my deck for your design and that wheel mod was damn genius. Most channels show the work done but not how to do it.
Thanks bro! I’m glad you enjoyed.
What a great idea. Thanks. Would work great for fly fishing too.
Thank you for putting this together. I wish we could have seen it on the water and all put together.
This is an amazing video that's sold me on getting a Colorado pontoon. I can't wait to get started on putting these mods onto it after I get it, especially love the deck.
Thank you Tyler!
Great job!! This is really well done and I am going to use most of your mods. I am using 1 inch aluminum instead of pvc and wood and putting the battery in a 4 inch deep cut out on my platform in front of the seat. The wheels I did exactly as you and it works great. The motor mount I am using 3, 1/2 inch pvc boards glued and bolted together. I have to say having the wheels down in the lake makes a huge difference…..great thinking. I truly appreciate you sharing your ideas and the professional way you produced the video. Huge thanks!
Beautiful job on your deck.
This is great thank you for sharing! Will be following your method for the casting deck accept use some old aluminum seats from a dingy for the deck.
Nice work, Brother! I’m in the market, & appreciate you sharing your mods. Also, love the shirt! 👊🏼
Awesome Casting Deck , just bought the material getting on that project ASAP
nice job
Great job bro that sucker is badass
Very nice, best I have seen
Ty
Nice!! I recently added a higher seat pedestal and found that if I have to ever row, I'm F'd. lol Its a challenge rowing with the high seat. I mostly troll for trout though. I like the batter under the seat idea. I bet that helps with the weight distribution. Great video.
That’s funny I just sent you a message, but I had the same rowing problem especially being over 6’ tall. Oar lock risers are probably the solution, but trolling motor beats all.
nice mods thank you
Just picked up the same pontoon and hopefully going to add my endura 30lb thrust trolling motor soon
Wonderful video. Saving up for the Colorado pontoon set up myself. Other than the #$@& mute button, outstanding run through. Will definitely be doing the casting deck idea, plus this jas given me so many other ideas. Thanks a bunch mate, really appreciate your video.
hell yeah buddy im going to do this set up
Love the mods… im thinking of getting one of these for my fishing channel, gonna make similar mods, but i want to add a pedal drive from a kayak
A pedal drive would be pretty sweet.
Great video, do you have a part number for the aluminum plank at Tommy Dock? I've looked over their site and don't see individual pieces like that
I like that shirt 😂
I like. We are seniors and need the seat very high. And want to be able to stand. Thank you. Nov 16, 2023
Great build. I have yet to do the platform and seat riser. What would happen if your battery or motor goes out? Are you bringing oars as well? I bring fins but I don't think I could kick when I'm in a raise position. In addition my rod holds, down rigger, and livescope is mounted on the side
I like the double tire mod. Platform is nice too. Im curios how much weight it added? I just changed over to a scadden recently whole boat is 28lbs.
Nice video showing awesome adaptations. Two questions, what height is your seat pedestal. And, are you able to lift off the battery case lid and remove battery without removing the seat first?
Great video, I have a few questions. Do you have a part number for the aluminum plank at Tommy Dock? I've looked over their site and don't see individual pieces, and how long are the deck planks.
So I just picked one of these up off Marketplace over the weekend. So when you put the casting deck on and a taller seat, does it feel top heavy?
Nicely done!
Have you ever attempted a re-entry with the casting deck on?
Could you do a much more detailed video on the wheel assembly ?
I have a fishcat 9’ and my frame setup is a little different with some diamond plate flooring behind the seat.... but there is a frame crossmember at the very back of the “floor”. If I had wheels I could exit the river in more places ...vs only where automobile access is very close.
How tall was the pedestal you used for the seat im getting ready to buy the Colorado xts and do the seat and platform mod that you showed
Did you have trouble with trolling motor shaft length and prop maybe bumping your tires?
I love all your nods and did then to my Colorado pontoon, but I want to ask how did you do the registration plate
In your material list you show 2- 1 1/4” x 3” ( four coupling) ?? Is this a 3” necked down to 1 1/4”?? Is this the black furniture pvc or white on this? Thank you for any information
May I ask what rod holders you purchased from Amazon? On the parts list for the seat is the hardware that attaches the swivel to the seat listed as well. Going through this very scenario and your solution is one I’d like to use. Thanks
Question...where can I get a bracket to make wheel set up mine didn't have one??
Hey! Great video! I just bought a used boat and they don’t have the original hardware…. So where did you get your black D-Rings?
You should make a kit for what you built.
There's a lot of good engineering in this!
Do you have these available to buy for the base colorado not the xt or xts? Id be very happy to purchase one from you?
I contacted Tommy Docks they are showing me a long piece of aluminum, did you cut those steps yourself from a piece of longer stock?
Love your mods! Quick question, what battery box do you use for your battery? I have a groups size 31 battery and I couldn’t really find a good battery box for it.
Thank you! I use this Newport Vessels Trolling Motor Smart Battery Box Power Center with USB and DC Ports a.co/d/4Xu3cP7 The dimensions look like it’ll fit a group 31 battery. From the description: Max Battery Fit - 13.75" x 7.5" x 9.75"
Do you have a material list for this modification?
This is easily over 100 bucks on just pvc, but super cool anyways!
Can you show how to make the wheels?
I would love to see this out for a fishing session! This is a great build. I think I am going to try this build with composite deck boards. Do you think the wooden dowels are a must have or could this be sturdy enough with just the PVC?
I built a casting deck following a guy named fish and forage, using pvc, and 1/2 plywood, it’s been a dream. Either method won’t steer you wrong.
Can you show more detail on how you raised the seat. Where or what did you use for the extension?
You can get those extensions from Amazin, Walmart, Bass pro, Cables, Academy etc
You're my only hope Obe-wan. Have tried every conceivable arrangement to attach the swivel to the seat bottom. Original seat bolts are too long and pass through both sections of the swivel, ie it won't rotate. Maybe I'm over thinking it. You obviously are far more skilled at solving these problems and better equipped than I.
@No3Jacks I had the same problem. I got shorter 1/4-20 hanger bolts and replaced the original ones with the short ones. This gave me clearance to mount the swivel to the frame.
@@patriotperspective9321 I gave up. I will try again now that I know the secret. Thanks for taking the time to reply.
@No3Jacks I will look at what length hanger bolts I used when I get home from work and report back.
@No3Jacks So, I used 1/4-20 x 2 in hanger bolts but I think you could use panhead screws with a corse thread on the seat side of your swivel to get good clearance as well.
What height pedestal did you use?
Great job, only question i have can you still row if you had too with the seat raised?
Rowing is considerably more difficult with the seat raised. I think if I extend the oars it would be better. I haven’t really rowed since putting the trolling motor on.
@@wiebercraft4974 what would be a great battery to buy for the troling motor
Can you put a link the the aluminum
Great job! What source did you use for the aluminum and furniture pvc?
I got the aluminum decking from tommydocks.com/products/aluminum-panel-47-3-4-x-5-1-2 I got the furniture grade pvc from Amazon. There’s a lot to pick from so just search Amazon for furniture grade pvc.
Thanks bud. Enjoyed the content and will look forward to more!
@@wiebercraft4974 thanks for the infomation. Did you just get one peice at 47 3/4 X 5 1/2 X 1 and cut it into 3 sections equaly.
I'm getting the one without the wheels. I wonder if I can add something similar? 🤔
If it’s one of the classic accessories pontoons you should be fine. I think they all have the bracket to hold a wheel.
Koltuğun dönmesini sağlayan linki atar mısınız
hello, you have already tried it on the sea is it adaptable? THANKS
Sorry, I never tried it on the sea. I think a kayak is better suited for salt water tho.
@@wiebercraft4974 thank you
How many planks do i need for the deck?
I used two planks. They were 48” long so I cut them in half.
What we’re the dimensions of the transom?
20-1/2" x 5" x 1-1/2". I glued two pieces of 3/4" plywood together to get the thickness.
Man can you make me the standing platform and ship it to my I will pay you I don't have the tools for this hit me up I'm for real serious about it.