- 17
- 42 300
Wieber Craft
United States
Приєднався 3 жов 2011
General fabrication and other oddities
Five Essential Classic Accessories Colorado XT Mods
These are the modification I made to my fishing pontoon to make it more comfortable to fish from.
PARTS LIST:
=======================================
Casting Deck
6) 1-1/4" PVC Tees
2) 1-1\4" x 18-1/4" PVC Pipe
1) 1-1/4" x 16" PVC Pipe
8) 1-1/4" x 1-1/2" PVC Pipe (for spacers)
2) 1-1/4" x 3" PVC Pipe (four coupling)
2) 1-3/8" x 18-1/4" Wood Dowel
1) 1-3/8" x 26-1/8" Wood Dowel
4) 6" x 24" Decking
6) 1/4" x 3-1/2" Carriage Bolts
6) 1/4" Nylon Stop Nuts
6) 1/4" Flat Washers
Seat
4) 5/16" x 1-1/2" Carriage Bolts
4) 5/16" Tee Handle Nuts
4) 5/16" Flat Washers
4) 1/4" x 3/4" Carriage Bolts
4) 1/4" Tee Handle Nuts
4) 1/4" Flat Washers
Battery Box
4) 5/16" x 1-1/2" Carriage Bolts
4) 5/16" Flat Washers
4) 5/16" Nylon Stop Nuts
Transom
1) 20-1/2" x 5" x 1-1/2" Wood for Transom
4) 3/8" x 3-1/2" Carriage Bolts
4) 3/8" Nylon Stop Nuts
4) 3/8" Flat Washers
Wheels
1) 1" x 1" x 12" Steel Tubing
1) 3/8" x 3-1/2" Hex Bolt
1) 3/8" Nylon Stop Nut
1) 3/8" Flat Washer
1) 3-1/2" D-Pin
PARTS LIST:
=======================================
Casting Deck
6) 1-1/4" PVC Tees
2) 1-1\4" x 18-1/4" PVC Pipe
1) 1-1/4" x 16" PVC Pipe
8) 1-1/4" x 1-1/2" PVC Pipe (for spacers)
2) 1-1/4" x 3" PVC Pipe (four coupling)
2) 1-3/8" x 18-1/4" Wood Dowel
1) 1-3/8" x 26-1/8" Wood Dowel
4) 6" x 24" Decking
6) 1/4" x 3-1/2" Carriage Bolts
6) 1/4" Nylon Stop Nuts
6) 1/4" Flat Washers
Seat
4) 5/16" x 1-1/2" Carriage Bolts
4) 5/16" Tee Handle Nuts
4) 5/16" Flat Washers
4) 1/4" x 3/4" Carriage Bolts
4) 1/4" Tee Handle Nuts
4) 1/4" Flat Washers
Battery Box
4) 5/16" x 1-1/2" Carriage Bolts
4) 5/16" Flat Washers
4) 5/16" Nylon Stop Nuts
Transom
1) 20-1/2" x 5" x 1-1/2" Wood for Transom
4) 3/8" x 3-1/2" Carriage Bolts
4) 3/8" Nylon Stop Nuts
4) 3/8" Flat Washers
Wheels
1) 1" x 1" x 12" Steel Tubing
1) 3/8" x 3-1/2" Hex Bolt
1) 3/8" Nylon Stop Nut
1) 3/8" Flat Washer
1) 3-1/2" D-Pin
Переглядів: 31 198
Відео
Skull Relief Carving Take Two
Переглядів 2712 роки тому
Mostly a time lapse video of a skull clawing its way through a wall (or maybe a door). The first attempt at this failed.
Skull Relief Carving Fail
Переглядів 5582 роки тому
A time lapse video of a skull clawing through a door that fails in the end.
DIY Upgrade MYSWEETY 3018 MAX to 3050 Part 3
Переглядів 6032 роки тому
This is the third and final video of this upgrade from 3018 to 3050
DIY Upgrade MYSWEETY 3018 MAX to 3050 Part 2
Переглядів 6412 роки тому
This is part two of my upgrade, this video deals with the Z axis.
DIY Upgrade MYSWEETY 3018 MAX to 3050
Переглядів 1,2 тис.2 роки тому
This is part one of three videos where I show the process of upgrading a MYSWEETY 3018 Max desktop CNC engraver without buying a pre-made kit.
Quick Tip Tapping Aluminum Extrusion on a Drill Press
Переглядів 2902 роки тому
Just a short little video showing a technique for tapping aluminum extrusion using a drill press to keep the tap square to the profile. Credits Music from Uppbeat (free for Creators!): uppbeat.io/t/cruen/along-the-road License code: CMYPTZINZLRSTJJ3
Perfect Dadoes Every time using a router and simple jig››!
Переглядів 812 роки тому
This is a short video showing my process for using the dado jig I showed in a previous video. Using this dado jig yields flawless dadoes every time. In the video I cut the dado to the exact width of a standard T-channel. For a looser fit, simply shim the object with a sheet of paper, playing card, or some painter's tape. Credits Music from Uppbeat (free for Creators!): uppbeat.io/t/adi-goldstei...
A quick tip on micro adjusting a cut
Переглядів 712 роки тому
In this short clip, my amazing son explains an easy and accurate method to make micro adjustments to fine tune a cut. This approach works for any size shim needed to get the perfect length. Obviously, this only works if the workpiece is oversized after the initial cut.
LaserYoYo
Переглядів 412 роки тому
Fun little engraving on a yo-yo my daughter and I made. Music from Uppbeat (free for Creators!): uppbeat.io/t/hey-pluto/get-freaky License code: 5TK7U
Edge Guide
Переглядів 172 роки тому
Made this video for a friend on how to make a simple and effective saw guide and decided to post it even though it’s short and underwhelming 😉
MYSWEETY 3018 MAX desktop CNC router Pt. 2
Переглядів 1,3 тис.2 роки тому
This video is part two of the unboxing video. In the previous video I couldn't test the machine because I needed some replacement parts. MySweety took care of everything! Music from Uppbeat (free for Creators!): First song: uppbeat.io/t/zoo/clarity License code: SWGMX3FOCSGECGPF Second song: uppbeat.io/t/mojo/rebel License code: 4GNM18HM0JNRQRPL
ToolsAndCaveScreenCast
Переглядів 4712 років тому
In this video I demonstrate the tool collection system and introduction a new tool, the compass. I also show how one way portals work and walk through the new cave environment.
WordSearchScreenCast
Переглядів 3612 років тому
Demo of a mini-game event from the aMaz3D video game. This one is a word search mini-game
You need to start over because you keep hitting toutr button
Excellent mods! Sub’d🎉
A pontoon vs a kayak which one would you say is better ??? I looking to but one or the other buy one but I’m not sure
It’s important to know that the Colorado XT has a wider frame than the wilderness. I followed you measurements without testing and measuring my frame. My platform looked great, but is too big for the wilderness. Now I need to redo things 😢
This is the most professional upgrade video I've seen. Well done.
Koltuğun dönmesini sağlayan linki atar mısınız
What a great idea. Thanks. Would work great for fly fishing too.
This is easily over 100 bucks on just pvc, but super cool anyways!
What height pedestal did you use?
Thank you for putting this together. I wish we could have seen it on the water and all put together.
nice job
So I just picked one of these up off Marketplace over the weekend. So when you put the casting deck on and a taller seat, does it feel top heavy?
Question...where can I get a bracket to make wheel set up mine didn't have one??
Just picked up the same pontoon and hopefully going to add my endura 30lb thrust trolling motor soon
You're my only hope Obe-wan. Have tried every conceivable arrangement to attach the swivel to the seat bottom. Original seat bolts are too long and pass through both sections of the swivel, ie it won't rotate. Maybe I'm over thinking it. You obviously are far more skilled at solving these problems and better equipped than I.
@No3Jacks I had the same problem. I got shorter 1/4-20 hanger bolts and replaced the original ones with the short ones. This gave me clearance to mount the swivel to the frame.
@@patriotperspective9321 I gave up. I will try again now that I know the secret. Thanks for taking the time to reply.
@No3Jacks I will look at what length hanger bolts I used when I get home from work and report back.
@No3Jacks So, I used 1/4-20 x 2 in hanger bolts but I think you could use panhead screws with a corse thread on the seat side of your swivel to get good clearance as well.
May I ask what rod holders you purchased from Amazon? On the parts list for the seat is the hardware that attaches the swivel to the seat listed as well. Going through this very scenario and your solution is one I’d like to use. Thanks
I love all your nods and did then to my Colorado pontoon, but I want to ask how did you do the registration plate
Wonderful video. Saving up for the Colorado pontoon set up myself. Other than the #$@& mute button, outstanding run through. Will definitely be doing the casting deck idea, plus this jas given me so many other ideas. Thanks a bunch mate, really appreciate your video.
Where did you get your extension kit from?
Aliexpress has anything you need.
Still love watching him
Beautiful job on your deck.
link para pedir uno?
I like the double tire mod. Platform is nice too. Im curios how much weight it added? I just changed over to a scadden recently whole boat is 28lbs.
I like. We are seniors and need the seat very high. And want to be able to stand. Thank you. Nov 16, 2023
Great video, I have a few questions. Do you have a part number for the aluminum plank at Tommy Dock? I've looked over their site and don't see individual pieces, and how long are the deck planks.
Nice work, Brother! I’m in the market, & appreciate you sharing your mods. Also, love the shirt! 👊🏼
Nicely done! Have you ever attempted a re-entry with the casting deck on?
Do you have a material list for this modification?
nice mods thank you
How tall was the pedestal you used for the seat im getting ready to buy the Colorado xts and do the seat and platform mod that you showed
Awesome Casting Deck , just bought the material getting on that project ASAP
I contacted Tommy Docks they are showing me a long piece of aluminum, did you cut those steps yourself from a piece of longer stock?
Great video, do you have a part number for the aluminum plank at Tommy Dock? I've looked over their site and don't see individual pieces like that
Hey! Great video! I just bought a used boat and they don’t have the original hardware…. So where did you get your black D-Rings?
In your material list you show 2- 1 1/4” x 3” ( four coupling) ?? Is this a 3” necked down to 1 1/4”?? Is this the black furniture pvc or white on this? Thank you for any information
Great job bro that sucker is badass
Did you have trouble with trolling motor shaft length and prop maybe bumping your tires?
Great job!! This is really well done and I am going to use most of your mods. I am using 1 inch aluminum instead of pvc and wood and putting the battery in a 4 inch deep cut out on my platform in front of the seat. The wheels I did exactly as you and it works great. The motor mount I am using 3, 1/2 inch pvc boards glued and bolted together. I have to say having the wheels down in the lake makes a huge difference…..great thinking. I truly appreciate you sharing your ideas and the professional way you produced the video. Huge thanks!
Nice video showing awesome adaptations. Two questions, what height is your seat pedestal. And, are you able to lift off the battery case lid and remove battery without removing the seat first?
Do you have these available to buy for the base colorado not the xt or xts? Id be very happy to purchase one from you?
Man can you make me the standing platform and ship it to my I will pay you I don't have the tools for this hit me up I'm for real serious about it.
Great build. I have yet to do the platform and seat riser. What would happen if your battery or motor goes out? Are you bringing oars as well? I bring fins but I don't think I could kick when I'm in a raise position. In addition my rod holds, down rigger, and livescope is mounted on the side
Can you put a link the the aluminum
hell yeah buddy im going to do this set up
I would love to see this out for a fishing session! This is a great build. I think I am going to try this build with composite deck boards. Do you think the wooden dowels are a must have or could this be sturdy enough with just the PVC?
I built a casting deck following a guy named fish and forage, using pvc, and 1/2 plywood, it’s been a dream. Either method won’t steer you wrong.
Can you show how to make the wheels?
Love the mods… im thinking of getting one of these for my fishing channel, gonna make similar mods, but i want to add a pedal drive from a kayak
A pedal drive would be pretty sweet.
hello, you have already tried it on the sea is it adaptable? THANKS
Sorry, I never tried it on the sea. I think a kayak is better suited for salt water tho.
@@wiebercraft4974 thank you
I'm getting the one without the wheels. I wonder if I can add something similar? 🤔
If it’s one of the classic accessories pontoons you should be fine. I think they all have the bracket to hold a wheel.
I like that shirt 😂