Intex Seahawk 4 Motor Mount Wheels / Transom wheels
Вставка
- Опубліковано 19 сер 2021
- Just wanted to show my idea of making the transom wheels of my inflatable boat.
I appreciate much for putting a little of your time on watching my videos.
Please consider hitting the red SUBSCRIBE button and the thumbs-up sign, and I would be grateful and happy for doing so.
=============================================================
Music from Uppbeat (free for Creators!):
uppbeat.io/t/reakt-music/deep...
License code: KEODNMCQSXDTMPR0 - Навчання та стиль
Amazing explanation of what , how and why. Thank you so much for the honky tonk guitar rifs. I will have my boat in the water in NO TIME.
Thanks for watching
Congratulation. Very clever Idea,
Thanks for watching
Omg 😮 I love it 😻
Thanks for watching
I like it! cool!
Thank you, I appreciate much.
Good job
Thanks for visiting my friend
Nice work
Thanks for watching
good review
Thank you 😊
👏👏👏👏👏💯 showwww
thanks for watching my friend
Great work! Thanks for sharing. Can I ask what size of U rings did you use that fitted the original screw holes so well?
Thanks for watching. The size of the U rings were 1/4 inch by 6 inch.
แวะมาทักทายให้กำลังใจกันและกันจ้า
Hello dear friend nice 👍 to meet you
Nice to meet you too and thank for watching my friend
You welcome dear friend thanks 🙏
Very nice. What size of the aluminum square pipes did you use?
1x1 inches. Thanks for watching
@@cesar8359 Thanks a lot
I have the Intex three and for some reason it’s losing air in the outer chamber every couple hours. Do you experience the same? It may be just an air molecules issue. Thanks mate
No, I haven't experienced that issue mate
I experienced similar issue with mariner 3 and took quite a while to figure it out. Most of leaks happen along the vertical seams. you may find these leaks using soapy water. They are very very small, the diameter of each bubble may be less the 1/4 millimeter. dozens bubbles show together after 1 min
with soap water at leaky point. I fixed about 100 +/- such leaks using LOCTITE Vinyl, Fabric and Plastic glue. AirStop also work, but much more expensive.
Great idea but much more practical and stronger with the floor in and other item's inside it to make a dolly/cart. Have you made a dolly for it yet?
You're right Mark dolly cart would be much stronger but I haven't made a dolly yet
@@cesar8359Just a thought, 10" wheels would be better I think because it would raise the stern of the boat higher.
@@markweatherall7437 thanks for the tip, it's a good idea but my boat has been punctured and can't be repaired that's why I switched to kayaking.
Hi, what is the size of aluminium profile ? I want to create the same gadget for my Mariner 4.
1 x 1 inch aluminum tubing, thanks for watching.
Bigger wheels would have done the trick......I'm using 11in wheels from an old bused lawn mower.....good vid
Thanks for the advice and for watching
Hello keep safe.its me eto po sukli ko...full pack sato.God bless
Salamat po at God bless din and stay connected po
Neat idea. It would be much better with some very simple directions/sketch/dimensions or, at least, a list of materials you used, Ce sar. Much more valuable if I could build it. As is, I wouldn't even try - I'm not that good! Thanks.
Thanks for the suggestion Jack appreciate it much.
Make a Dolly instead, much better.
New subscriber here. Is it possible if you could share the materials you have used to this nice and very simple transom wheels you have made? I truly appreciated if you could. please and thank you.
Thanks for watching and for subscribing, appreciate it much 🙏. The materials I used were a 1x1 aluminum tubing, 3/8 × 2 3/4 nuts and bolts, plastic wheels, 1/4 × 4 U bolts with nuts and locking pins
@@cesar8359 thank you so much. Take care ❤ bro.
🤣