When you broke the four-wire cable for charging and data transmission, you made the following mistake: 1) on contact D- you replaced the green electric wire (white electric wire goes to D-), 2) you replaced the white electrical wire on D+ (the green electrical wire goes to D+).
You are also wrong the the wires are crossed, positive to negative, white wire goes from D- on one side to D+ on the other and the same for the green cable but on the other board.
Thanks for the helpful video! I'm a complete novice with this stuff, so I have a dumb question. Uhhh...what are those 2 tools called? The ones you start using at 01:08
@@ydiadi_ Thanks! I thought so, but then the ones I looked up were different than what he's using. My coworker told me today that he's got a fine tip on it or something. Does that sound right to you? If you could send a link to an amazon listing or something, I'd really appreciate it!
@@jonathandoda8762 Soldering iron's tip should be very fine like if you want to solder an IC (integrated chip) , as you can see type C's solder to that circuit was very minute and small. Hence search for some micro soldering machines on Amazon.
I'm a bit of a beginner to electronics, but I'm wondering what the green and white wires are for? Data transfer? If I only wanted power to the cable, would these wires be needed? Thanks!
The D+ is data positive and the D- is data negative. Data is transferred in duplex technically there is no positive and negative here. One side sends pulses down the negative to the positive and the other side does the same. Basically two one way streets in opposite directions. For how the data is sent is explained by digital technology.
Super helpful video! :) What gray material did you mix with the M-Seul epoxy compound for a new seal? I'm sadly novice to this process and atm simply need to refasten a cable's smaller male input that comes off, but it still charges perfectly if a little pressure is applied to a phone/device.
You are a King! This is something that the rest of us slaves just go to the store and HOPE that they used copper thicker than a human hair. I love it. DIY it vs. buy it.
the red and black they sure the power tracks right? but what if i disconnect the both of them i just need the two data tracks for using the cable to read data only from a small camera to my smart phone with type c OTG in the USD A and this camera has a small battery that always charging my smart phone 😬⛔📵 I don't wanna charge it from the camera's battery? so if i disconnected the two power tracks and left the two data transfer tracks is this gonna work or some cable needs the the power tracks with the two data tracks to help with transfer data? umm i hope you got what i mean pls i need your help 🙏
In the video in which you showed the repair of a male type C connector, you made the following mistake: you soldered a green electrical wire to contact D-, and a white electrical wire to contact D+. As a rule, it is: The white electrical wire goes to the contact D-, and the green electrical wire goes to the contact D+.
I'm just saying but I couldn't help but notice (Only because I cannot use my controller for my xbox, which is the only thing that provides sound, due to the fact that I need batteries OR a USB type-C charger for power. Hence, why I'm using subtitles) that the subtitles need to chill. I can't tell if that was intention because I have no audio.
Yo los tiro y vuelvo a comprar mi hijo lo quema por que lo deja conectado todo el dia pero yo tengo uno que me a durado por que solo cargo el cell y lo desconecto y escondo el cable
You shouldn't move the cables while soldering a connection. Always use a "3rd hand", a fixing device with clamps. As you can see from the black cable, this otherwise will result in a bad connection. Why such amateur performance in an otherwise skilled video?
Hello my friend. On a micro USB cable the colors black and red are they always inverted? I mean , on the the USB its from the right : Red then black and the on the micro usb from the right its black then red? Why is that? shouldn't they be the same? What if we soldered them the same. what could happen??
Muy buen video gracias , esperamos mas videos como este ...
Super bro, with this I repaired my type c otg
🙏🙏👍👍
Just i India 😅 Good job bro❤
Well skilled hand in soldering
And it will charge at 100A in a future usb-c 15.3. Good job and good cable, not the products you can buy.
Thanks brother
I was finding this video but finally i got it successfully 💓
When you broke the four-wire cable for charging and data transmission, you made the following mistake:
1) on contact D- you replaced the green electric wire (white electric wire goes to D-),
2) you replaced the white electrical wire on D+ (the green electrical wire goes to D+).
You are also wrong the the wires are crossed, positive to negative, white wire goes from D- on one side to D+ on the other and the same for the green cable but on the other board.
Bhuat hi good working So nice 🌷🌹🌷
buenos días me gustó el video como puedo buscar esos cables de colores que nombre tienen
Bhai vooc type c ki cable repair kese kere wo bhi batao na fast charging support nrhi kerti
Reply bro
😂
Nice vid mate! Thanks from 🇦🇺
Thanks bro 👍
Charging point kounse hai or data ke liye kounse point hai?..
good job Rj.thanks all
Pls make. Tybec to lighting
Ok sure I’ll,
Super Bro
Mujhe Video Aachi Lagi
Aap Ne Bhut Aasan Tareka Bataeya Charger Leed Sahi Karne Ka
Good Job
👍👍❤️❤️
Bro Chanel KO subscribe Kar Lena, aage aane wale video sayad aap ke kam ho,❤️❤️
Rất OK và chuẩn chỉ. 🤔
Thanks. So clean.
जय हो जुगाड
OK this video is fine as a proof of concept but in reality, just that sealing putty at 3:31 is probably more expensive than simply a new cable.
“Let them eat cake”
But you could use hide glue from a roadkill and cook it with scrap wood out back. Couldn’t we?
Fast charging k liay kitnay power ka wire use karengy kitnay gauge ka ho mota ho ya barik wire?
0.25 0.50 ya 0.75 full gauge copper wire (SWG) use kar sakte hai,
Thank you, I'm trying to replace usb-c with usb-a 2.0 connector.
Use fast charger adapter to usb type-c
Una pregunta, los cables de datos van en sentidos opuesto??
Sorry I didn't understand your comment,
The image in the video is inverted, mirrored. this shows the cable colors backwards, not good.
you are good tech
Thanks for the helpful video!
I'm a complete novice with this stuff, so I have a dumb question. Uhhh...what are those 2 tools called? The ones you start using at 01:08
🙏🙏🙏
Screw driver and soldering iron
@@ydiadi_ Thanks! I thought so, but then the ones I looked up were different than what he's using.
My coworker told me today that he's got a fine tip on it or something.
Does that sound right to you? If you could send a link to an amazon listing or something, I'd really appreciate it!
@@jonathandoda8762 Soldering iron's tip should be very fine like if you want to solder an IC (integrated chip) , as you can see type C's solder to that circuit was very minute and small. Hence search for some micro soldering machines on Amazon.
I'm a bit of a beginner to electronics, but I'm wondering what the green and white wires are for? Data transfer? If I only wanted power to the cable, would these wires be needed?
Thanks!
Yes they are for data, you don't need them to charge your phone
Just be careful since some phones use them to communicate with your charger to check fast charge compatibility
The D+ is data positive and the D- is data negative. Data is transferred in duplex technically there is no positive and negative here. One side sends pulses down the negative to the positive and the other side does the same. Basically two one way streets in opposite directions. For how the data is sent is explained by digital technology.
super
Thanks
Super helpful video! :) What gray material did you mix with the M-Seul epoxy compound for a new seal? I'm sadly novice to this process and atm simply need to refasten a cable's smaller male input that comes off, but it still charges perfectly if a little pressure is applied to a phone/device.
jb weld
а мне от Анкер компании нравятся кабеля они очень прочные и качественные, выдерживают более 30к сгибаний)
Hello, I will repair the insulation of my mains test cable. What is the name of the mixture of black and gray dough
Hi, Thank you for like, is name plastic glue?
Maine try kiya but agar mi company ka original rahega toh re solder ho sakta hai.
Local company ka karne jate hai to track damage ho jate hai. 🙏
Yes orginal hi hona chahiye,,,
Is it wrong?on the head type c Is the green and white wires interchangeable?
It's not, he made mistake it's supposed to be red green white black
You are a King! This is something that the rest of us slaves just go to the store and HOPE that they used copper thicker than a human hair. I love it. DIY it vs. buy it.
Kullandığınız o madde nedir?
the red and black they sure the power tracks right? but what if i disconnect the both of them i just need the two data tracks for using the cable to read data only from a small camera to my smart phone with type c OTG in the USD A and this camera has a small battery that always charging my smart phone 😬⛔📵 I don't wanna charge it from the camera's battery? so if i disconnected the two power tracks and left the two data transfer tracks is this gonna work or some cable needs the the power tracks with the two data tracks to help with transfer data? umm i hope you got what i mean pls i need your help 🙏
No! It will not happen. If you will not connect the four wires in the USB. Please connect all for wires otherwise it will not work ❤️❤️❤️
Video use hue component ya chize kon batayega
Very nice!
I'm asking for a list of all equipment used?
Hàn sai dây rồi. Dây trắng bao giờ cũng cạnh dây đỏ nhé!
Hello bro please write in English, I am unable to understand,
@@rjelectro66
Soldering order: Red, white, green, black wire!
Por que las conexiones de los cables en los conectores,tanto el macho como el c ,no son simetricas....?
porque se equivoquó jajajq
,,НЕЙРОХИРУРГИЯ"👍👍👍.
Thanks bro..
@@rjelectro66 Микроскоп используете?🤔🤔🤔Сам паял-только испортил.
Good. Better get new one lol😂
Nice video. Is there some reason why the red and black wires are thicker than the rest?
Red and black are the energy cables the rest just for data transfer
y para un micro usb no tiene un video
In the video in which you showed the repair of a male type C connector, you made the following mistake: you soldered a green electrical wire to contact D-, and a white electrical wire to contact D+.
As a rule, it is:
The white electrical wire goes to the contact D-, and the green electrical wire goes to the contact D+.
I noticed a switch in position in the data -ve and data +ve at both end. I mean the grean nad white wire.
Yes I know its happened by mistake so sorry,
Yo I have a problem with the pins extending out of the mother board but are still connected but it won't charge
Разменил си кабелите белия и зеления на буксата дето влиза в телефона.
👍💚🤍❤👍👌
👍
It's not, he made mistake it's supposed to be red green white black
Cubran con pegamento o hot glue las partes rotas y listo.
Nice
Well it’s better to buy a new charger
Just the USB 2.0 lanes?
cool
Wtf I actually like the music on one of these videos
Thanks,
А у меня кабель 5 жил . + Желтый провод . Что делать ?
Cover with hot glue to any broken part and ready
대단해요
Bro which wires have u used please reply i have been searching
Bro you can use .5mm square couper wire, or old any other standered USB cable wire,
@@rjelectro66 thanks bro , actually i am making my own custon cable from scratch and need the wire and cant find it
Please sir, how to repair Samsung E1200 cable like you repair this Type C cable ?
Bro which type of soldering iron are u use? What is the name of thiss please tell me.thanks♥️♥️🥀🥀
Bro it's simple soldering iron,(name soldron)
Maybe hot glue would be better than dough.
Bro This material is a type of resin and hardner, which is used after mixing, later becomes very hard and tight material,
M-seal sai shock tohh nahi lagi ga naa
Nahi lagta m seal se shock
I'm just saying but I couldn't help but notice (Only because I cannot use my controller for my xbox, which is the only thing that provides sound, due to the fact that I need batteries OR a USB type-C charger for power. Hence, why I'm using subtitles) that the subtitles need to chill. I can't tell if that was intention because I have no audio.
Sería muy bueno qué lo esplicaran verbalmente soy de Palmira Valle Colombia gracias
Also write down the name of the liquid you have done
Bro liquid name Soldering flux,,,
Looking for a way to make case opening larger
И зачем надо было откусывать штекеры? Выкусили бы повреждённый маленький участок кабеля и спаяли бы провода между собой по цвету.
Yo los tiro y vuelvo a comprar mi hijo lo quema por que lo deja conectado todo el dia pero yo tengo uno que me a durado por que solo cargo el cell y lo desconecto y escondo el cable
Hi, is it possible to make usb type C to ethernet RJ45 cable?
Please don't just charge show ampere in charge meter App. how much it's faster
1800ma is enough for 2A charger
only for charging, dosn't work for data transfer
great video, what temperature do you use?
Bro I used simple soldering iron, Temprature approx 250 above,,
@@rjelectro66 haha perhaps I must have a bad tip, it takes me ages to wet solder on a board
Im already try but after that my charger cable becomes slowly charging how to fix this
If your cable &charger are original not possible for slow charge,
You shouldn't move the cables while soldering a connection. Always use a "3rd hand", a fixing device with clamps. As you can see from the black cable, this otherwise will result in a bad connection. Why such amateur performance in an otherwise skilled video?
support qc 3 or not ?
Bro mera bhi charger ki pin bhar a gyi hai kese thik karu me 😭😭😭😭😭
What is happening in 1:28, what is he doing ?
Where did u buy c type socket
Amazon bro
هناك خطأ في اماكن الاسلاك.....
Name song music?
можшо и в термоусадку засунуть так красивее будет
Kitne amphere ki taar lagani h
0.5 mm square standerd wire
I mean Choty Choty parts Jo hain ye
Ye cheezain. Me kahan se buy kr skta new
Kisi bhi mobile shop se,,
Hello my friend.
On a micro USB cable the colors black and red are they always inverted?
I mean , on the the USB its from the right : Red then black and the on the micro usb
from the right its black then red?
Why is that? shouldn't they be the same?
What if we soldered them the same. what could happen??
it should be the same it should always be ground and positive
Bhai song name
как можно с такими грязными руками ходить
Thanks for insult…
Where can I get wire glue
You can get wire glue in the electrical shop or hardware shop,,,thanks
How to otg type c suhu
咩膠?
Music was annoying AF
Bro fast charging is not working
Bro it is only repair not fast charging,,,❤️❤️
0:52 this blade name
손좀 씻고 하셔도 됩니다
Agar sab wire black ho to
Bro sab wire black nahi ho sakte kyoki wire ka Standardizetion hota hai
how about type c vooc? if I'm not mistaken there are 6 cables.
Kukunya 🙄
😂😂 bro minus m ja rah charging
Wire अच्छी quality ka यूज करो और चार्जर भी बिलकुल सही चार्ज होगा
Hjjjjjj
song?
Or don't be cheap or poor and buy a new one
I have a 15 footer I use for my occulus headset that cost $80. You wanna buy me a new one moneybags?