4L60E TRANSMISSION INSTALL || EASY
Вставка
- Опубліковано 12 лип 2024
- “Transmission to engine bolts: 35 ft/lb”
Once you have the transmission installed onto the engine you must verify that the torque converter
remained fully seated into the front pump during the transmission installation. You should observe 1/8”
(.125”) to 3/16” (.187”) of air gap between the torque converter mounting pads and flexplate before
sliding the converter forward to attach it to the flexplate. If you have 1/8” - 3/16” air gap then you may
proceed with sliding the torque converter forward and attaching it to the flexplate. If you have less than
1/8” air gap then you may not have the torque converter fully seated into the front pump. This will
require disassembly and verification of proper torque converter installation. If you have more than 3/16”
air gap then you may install high quality flat washers between the mounting pads and flexplate to shim
the converter to the correct air gap dimension of 1/8” - 3/16”. NEVER shim the converter to eliminate all
air gap. Running the torque converter in a fully shimmed condition WILL result in damage to the front
pump gear set, front pump stator body, torque converter pump hub, and may even cause damage to the
internal torque converter components as well as the crankshaft thrust bearing.
TOOLS USED IN THIS VIDEO
BLACK+DECKER Magnetic Screwdriver Set: amzn.to/3MQtOdV
HUSKY, HD00120, 3-Ton Low Profile Floor Jack with Speedy Lift: amzn.to/3OeaBDX
CRAFTSMAN Deep Impact Socket, Metric, 1/2-Inch Drive, 22mm:amzn.to/3mO09aQ
Kobalt KCW 5024B-03 24-Volt Max 1/2-in Drive Brushless Cordless Impact Wrench:
amzn.to/3Ojv62h
BIG RED T43202 Torin Steel Jack Stands: 3 Ton (6,000 lb) Capacity, Red, 1 Pair: amzn.to/3aVE3QP
Blackhawk B6350 Black/Red Fast Lift Service Jack: amzn.to/3OiJ18S
Ironclad General Utility Work Gloves GUG: amzn.to/3aPSmGu
DEWALT Socket Set, 3/8-Inch Drive: amzn.to/3xv58C8
EPAuto 1/2-inch Drive Click Torque Wrench: amzn.to/3NTO0wQ
3M Scotch Vinyl Electrical Tape Super 88, Premium Grade All-Weather: amzn.to/3aSKCnf
TOOLGUARDS 15mm Wrench: amzn.to/39rqrMI
Pry Bar Set, Heavy Duty Pry Bar 4-Piece Mechanic Hand Tools: amzn.to/3QhjMWh
GEARWRENCH 4 Pc. 3/8" Drive Wobble Extension Set: amzn.to/3Qz8H31
MIXPOWER 15-piece 3/8" Drive Shallow Universal Impact Socket Set: amzn.to/3tCP93D
DEWALT 20V MAX* LED Work Light, Hand Held: amzn.to/3xNZyMw
Transmission Mount: amzn.to/3HqoNYd
Kobalt 20-Piece Standard: amzn.to/3xzhysO
Wheel Bearing Grease Red: amzn.to/3xvl5bt
Valvoline Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid: amzn.to/3mLxvH1
3M Assorted Grit Emery Cloth Sandpaper: amzn.to/3OcuP0W
Super Funnel: amzn.to/3xwBGvD
Valvoline, Dexron/Merc, 1 Gal: amzn.to/3xvnqTA
Oil Drain Pan: amzn.to/39mazer
Our Socials!
Instagram - dudewecanfixit?...
Facebook - / dude-we-can-fix-it-103...
Learn how to Install your transmission with this step by step tutorial. Super simple and easy to follow!
When Adding Transmission Fluid, start with 6 Quarts and add as necessary.
▬ Contents of this video ▬▬▬▬▬▬▬▬▬▬
0:00 - Introduction
0:39 - Lift Vehicle
1:53 - Torque converter
2:42 - Lift Transmission
5:31 - Lower Bell Housing Bolts
6:10 - Torque Converter Bolts
9:51 - Upper Bell Housing Bolts
13:27 - Vent Hose
13:45 - Neutral Safety Switch
14:22 - Shifter Linkage
14:43 - Oil Cooler Lines
15:14 - Electrical Harness
15:30 - Exhaust
17:29 - Trans Mount & Crossmember
20:10 - Drive Shaft
21:44 - Heat Shield
22:05 - Starter
24:53 - Battery
25:11 - Trans Fluid
27:44 - Outro
DJI Mavic Air 2: amzn.to/33FVyhG
GOPRO Hero 7 Black: amzn.to/2VyE6aj
SanDisk 128gb Ultra Flair USB Flash Drive: amzn.to/3g6eLOB
Disclaimer: We receive commission off of sales made through the links above. This does not cost you any extra & we appreciate your support so much! Thank you guys for everything that you do for us. - Авто та транспорт
New video alert! ua-cam.com/video/eT_slcxBV1Q/v-deo.html
No qqq jqwj(jj
Q
Qoapa
No qqq jqwj(jj
Q
Qoapa
Who needs a shop when you guys like this with a UA-cam channel 👌🏾😮💨💪🏾
Lol, for real
Keep doing what your doing I was able to pull my transmission within an hour and a half from watching your video
That's awesome! Please subscribe to our channel and tell your friends!
Bro same these guys are legit
Thanks! Please subscribe and share our channel!
Buying a 2002 Tahoe tomorrow and I feel the transmission is going to need to come out for work.
I'll be using your videos! Great stuff
@@itsmebrysonp Happy we are able to help!
Haven’t found a good video until now that shows how to do this and this is applicable to many transmissions not just a 4L60e can’t wait to see what other content you guys put out!
Thank you for the nice comment! We work hard to put out useful content. Please help us grow by subscribing and sharing our channel!
they aren't selling the flywheel bolts with the socket heads on Amazon, so thanks for showing us the install with the 15mm wrench because that's my only option. Man, I wish I had a best friend working with me.
Glad I could help
The best how to I’ve seen yet!! GREAT DETAILS!!!🔥🔥🔥🔥
Thank you for the comment!
You guys make a great team! With the right hands and safety precautions, you're doing a great job! Very impressive in doing something most of us would not dare attempt! It's your world! Be the king in it!
Thank you! I love reading constructive comments like this one
@@dudewecanfixit The biggest problem in the world today is lack of gratitude! It does not cost a cent for a smile or a thank you when someone does a good service. I'm a house painter that teaches everything I know in my field. To do what you did here is àwkward, stressful and dangerous! I commend your courage!
Thanks, I have much respect for painters. I own an AC company and deal with all the trades. Hardest GOOD people to find are carpenters and painters. Be careful on those tall gables, a good painter friend of mine got an early retirement from one.
@@dudewecanfixit thank you but I have a way to beat some of the height. I simply paint the overhang from below and the facia from the roof. That is if someone was lucky that I did it for them at all. I became an interior specialist.ua-cam.com/users/shortsuVML6nANHYM?feature=share
THANK YOU, helped me greatly. Watched this and I also followed the step by step video for my rebuild and it helped me a lot.
That's fantastic! I'm glad we could be of assistance. Is there anything that you would change? Please subscribe and share our channel.
Keep up the good work dudes.
Love the videos and y'all explain things were people can actually understand what your talking about...
Thanks! We will
This is another great vid. by you. You had a steady camera, your hands were out of the way so we could see what you were talking about and you were very articulate. I appreciate how you fast forwarded the parts were your just cranking on the ratchet, etc. You are a good teacher. Thank you again for this. It saved me $$$$
Thank you so much! We took our time to make sure we were able to bring the best quality videos to you guys. Thank you for all the support and kind words!
You guys are awesome thank you! was able to do it myself watching this video saved me some money and shes running great
That's fantastic!
Of all videos
This video by far is the best video with step by step detailed yet. THX!
5 STAR
Thank you so much! Please subscribe to our channel
Thank you did this whit my son finished it today test drove it ...works flawlessly. Thank you
That's awesome! Congratulations! I'm glad it worked out for you guys. Please subscribe to our channel and share it with some friends.
Hey guys, it's Connor from WHS. Just wanted to let you know that I think you all are doing great on this UA-cam channel, and I wish you guys nothing but the best of luck!
Hey man, we appreciate the support! If you haven't already, please subscribe and share the channel to help us grow!
Great video man. Your patience is shown in your mannerism and in your voice. It shows that youve been doing this for years..
Unfortunately, still over my head. I woulnt dare try this myself. If i had an extra car, i would , Unfortunately its my daily driver and cannot be without a car for to long.
Thank you so much for the comment! Videoing a repair takes 4x as long as just doing the repair
Hello, I just want to take this time out to say thank you for this amazing video series. Because of it, I was able to remove my transmission, replace my rear main seal, and reinstall my transmission on my 2004 Chevy Silverado.
We appreciate you leaving us a comment. It warms our souls to know that we are helping people learn and save money.
Your Description on How and Where the Transmission Dipstick Tube goes, was great ! Once I listened to Where tube should be located, it went in almost Perfect ! Prior to your video I literally spent Hours with NO Luck ! Thanks for your time making this Video. 2005 Tahoe, 2WD.
You have no idea the same thing happen to us! That’s why we were able to be so specific about it lol Happy everything else went well for you! Thanks for watching and supporting
Nice job guys. Really well recorded. I will forward this video to my grandmother so she can get started. No, seriously, very well done and easy to follow.
Thanks!! Lol
Helped me out tons! Luckily I didn't have to remove the exhaust from my 95 silverado and the removable dust cover under the bell housing make the install 50x better. Great video series, enjoyed it thoroughly 👍
So happy we are able to help and happy you enjoyed the video! We try our best to help where we can!
Thanks homie. My 04 S10 crew decided to take a shit on our road trip. Appreciate it!
Thank you for sharing your knowledge 🙏, this is a high quality step by step video.
Thanks, I'm glad you enjoyed it
👍🏻Fantastic this video and the whole entire playlist deserve well over 100K views👍🏻
Thanks!
Great video. Audio and video was on point and helped us a lot! Still have some steps but we are almost there. Thanks!
Thanks!
You can do it!
Thank you 👍 for your video I was able to fully rebuild my 4l60e off my 06 Silverado
Yes! Stoked to hear this. We try hard to make our content is everything you need go get the job done. Hope we won your subscription!
Dude this was a great video as I’m about to tackle mine. Thanks so helpful!
I'm glad we could help!
Thanks for the video. Your install video looked as easy as the removal. I just wish i could het my truck up as high ad you did.
I have used blocks of wood before to increase height, but whatever you do, make sure it is very stable before you get underneath the vehicle!
You guys have been life savers with these vids!!!
Thank you!
Thank you! for this great 👍 video I was able to remove and overhaul my 4l60e.
That's great, good job!
Hey .... Did you know.... if you put Transmission Fluid in the transmission it makes the vehicle move? jajaja jajaj....I just didn't have enough fluid in the tranny before trying to get the vehicle to move. It was a learning experience and I couldn't have done it without you .. Thank You so Much!!! May God richly bless you as you continue to bless others.. and thank you for responding as you did. I so appreciate you.. Most Respectfully Andrew Allen
I'm glad you got something out of the video! It's always a learning experience, I put too much fluid in ..
Just did a full rebuild on my 01 jimmy. It's a lot more in depth for a 1st timer but I truly enjoyed rebuilding the tranny, adding sonnax shift kit, parts of transgo shift kit, corvette servo and a sonnax sun shell which was my problem in the first case. Totally stripped out 😆. But I would like to thank you two on a job well done. Especially with the feeler gauges, tolerances, and the confidence to do this job. I would've been up shit creek if not for you 2. I had a dam check ball fall into the side of the transmission 😆 and I double checked to make sure the c clips on the pump valve were fully seated then it got away from me and into the transmission again 🤦 but shit, I didn't even mind digging it out lol. Now I know I can rebuild one of these things and next would be engine dismantling but that's for another time. Much respect from Saskatchewan Canada 🇨🇦
That's awesome! I'm glad we could help you do all of that!
We do have videos on how to take the heads off, replace the head gasket, and reinstall on an LS engine!
@@dudewecanfixit I think I'll be using that in the future for sure. Once again. Thank you.
Glad I could help!
Whoever raised you ...should tell them thank you for doing such a good job
Thanks, it was neglect. But difficult circumstances create good character
@@dudewecanfixit💯💯
Amazing in detail step by step video thank you!
I appreciate the feedback!
You make this look much easier than I thought it would be!
lol! i hear you man
Great video by the way, great step by step detail 👌
Thank you!
Awesome job. The explaining is outstanding. Subscribed.
Thanks, we appreciate you subscribing also!
What amazes me is how three small bolts holding it to the torque converter can take all that power and not just strip them off and it's still amazes me
Same here, lol. Look up the sheer strength of a "half inch grade 8 bolt".
Very impressive
Great, informative video. I like your attention to safety and how you try to give as much info as possible.
A couple things I found out the hard way:
1. If the old trans went out, you need to flush the oil cooler with brake cleaner and compressed air or it can fill your newly rebuilt transmission with junk.
2. Lube the back of the crank with grease before you stick the torque converter in there. This allows the converter to move forward and back as the flexplate flexes.
3. Put the exhaust above the crossmember but don’t attach it until you put the inside bolt on the driver’s side in the crossmember or the bolt will have to go in backwards from the rest.
4. If you installed a new converter too, when you bolt it to the flexplate, make sure there is less than 3/16” gap between them. If not, you will need washers to close the gap.
5. Depending on the year, the starter wires are too short to install until the starter is mounted.
Your video on removing the hot glue connectors on the neutral safety switch saved me a huge headache!
Keep up the great work!
That's great, thank you for the very thorough follow-up!
I'm about to undetake this process, what type of grease did you use on the TC to crank?
Do you really trust flushing the lines will take care of your future problem? should you essentially replace lines, radiator,and trans-cooler?
Either trans lube or red wheel bearing grease
My transmission didn't have a catastrophic failure, so I'm fine with flushing the lines.
If it did have a catastrophic failure, I would install an auxiliary cooler and bypass the trans cooler in the radiator. I have a video on the auxiliary cooler install.
These videos give me all the confidence.. imma switch my tranny out with a decent used one then rebuild the one I take out just to gain the skills to do it.. and save me idk 2 grand..
Sounds like a great plan! You can do it
👍Thanks for This video it helped me tremendously doing my first transmission swap this weekend was able to knock it out in a day
Nice work!
Awesome series! Fully rebuilt my transmission with your videos!
That's awesome, good job!
Real quick tho, got everything together and back on the truck. I shifted thru the gears like you did, but I don't have Reverse.. before I take it off the truck again, would you have an idea of what could be the problem?
Is your fluid level 100% correct?
Reverse takes the most fluid pressure to operate.
Also, does the linkage feel normal shifting through all gears?
I've check the fluid multiple times. It's withing range.
And yes, feels like it should
That's interesting. I'm not sure what the next most prevalent item would be
Dude i think the old man fixed it I think you got to give the old man credit I watched all the episodes looks like he was doing the rebuilding just saying I loved watching it great info great video but man that guy knew his shit.
Yes, he definitely got it fixed. You should watch the 4L60 series! I go through every step of removing, rebuilding, and installing the transmission. It's a more complete series than the Dodge, I think you'll like it!
thank you very much for this upload!
You're welcome! Thanks for the comment
I followed your series and my van is running great after reinstalling it a year ago!
Nice work!
You guys are doing an awesome job. Thanks. Very clear and understandable
Thank you, please subscribe to our channel
Beasts very knowledgeable. Great video !
Thank you for the review! Please subscribe to our channel for future videos
Great how to, enough to confidently go try this on my 03 Silverado with a buddy. Will check back in
Let me know how it goes!
@@dudewecanfixit change of plans, doing it solo and in the driveway was going to start today but was nearly -20 with wind-chill. Starting it tomorrow will check back in afterwards 👍👍
Good luck, take your time and stay warm! It really helps to have someone for lowering the transmission to the ground, even if they are only there for 30 minutes
Any success?
Thank you guys. You saved me some frustration
Money and frustration! Happy to help
I been studying this video and the other one I'm about take one out of my 97 chevy pickup I just need a kick start and for it cool down a little lol thanks for the video I hope it it helps me
We hope it helps! It's helped a lot of others if it makes you feel any better. Thank you for watching and supporting!
It helped me out a lot thanks now have little shake going down road afterwards it's hard to tell just bad luck I guess
I’m watching these series so I can replace the rear main seal on my 5.3 Silverado only to just now realize I forgot about the 4wd part and now I gotta figure out how to remove the t-case 😂
You will have the front driveshaft (4 small bolts on the retaining clamps) and 6 bolts holding the transfer case to the transmission.
Very Helpful Thank you.
Keep it up I’m about to try my 08 gmc sierra 1500 2 wheel drive it has a lift so it’s a lil easier! Thank you for your help!
That's awesome! The lift should help!
Very detailed video!!!!!!! Thank you
Thank you so much! Please subscribe to our channel
Thank You, Thank You, Thank You. You answered my question!!!!
Glad I could be of use!
Wow. You guys are very thorough. I subscribed. I just had my transmission rebuilt. It came out good. But I was wondering how . Thank you next time I feel like I can take it out myself and install. Not sure on rebuilding it myself. 🤔
That's great, thanks! Doing the R&R (Removal and Reinstall) as the transmission shops call it, can usually save you $400 - $600. Not bad for a couple afternoons of work if you are mechanically inclined. You will also become a lot more comfortable/understanding of your vehicle
@@dudewecanfixit ... yeah I am mechanically inclined. The only thing is I'm not so confident that I can rebuild it. But I just want to say thank you for your time and videos. They have and will be of great help for me.
I'm glad to hear it and we appreciate the feedback! If you have any other mechanically inclined friends, please let them know about our channel too.
@@dudewecanfixit ... ok will do thanks
Thank you sir! New subscriber 👍
We appreciate the subscribe, it helps us more than you know! Please share with your family and friends.
“Transmission to engine bolts: 35 ft/lb”
TOOLS USED IN THIS VIDEO
BLACK+DECKER Magnetic Screwdriver Set: amzn.to/3MQtOdV
HUSKY, HD00120, 3-Ton Low Profile Floor Jack with Speedy Lift: amzn.to/3OeaBDX
CRAFTSMAN Deep Impact Socket, Metric, 1/2-Inch Drive, 22mm:amzn.to/3mO09aQ
Kobalt KCW 5024B-03 24-Volt Max 1/2-in Drive Brushless Cordless Impact Wrench:
amzn.to/3Ojv62h
BIG RED T43202 Torin Steel Jack Stands: 3 Ton (6,000 lb) Capacity, Red, 1 Pair: amzn.to/3aVE3QP
Blackhawk B6350 Black/Red Fast Lift Service Jack: amzn.to/3OiJ18S
Ironclad General Utility Work Gloves GUG: amzn.to/3aPSmGu
DEWALT Socket Set, 3/8-Inch Drive: amzn.to/3xv58C8
EPAuto 1/2-inch Drive Click Torque Wrench: amzn.to/3NTO0wQ
3M Scotch Vinyl Electrical Tape Super 88, Premium Grade All-Weather: amzn.to/3aSKCnf
TOOLGUARDS 15mm Wrench: amzn.to/39rqrMI
Pry Bar Set, Heavy Duty Pry Bar 4-Piece Mechanic Hand Tools: amzn.to/3QhjMWh
GEARWRENCH 4 Pc. 3/8" Drive Wobble Extension Set: amzn.to/3Qz8H31
MIXPOWER 15-piece 3/8" Drive Shallow Universal Impact Socket Set: amzn.to/3tCP93D
DEWALT 20V MAX* LED Work Light, Hand Held: amzn.to/3xNZyMw
Transmission Mount: amzn.to/3HqoNYd
Kobalt 20-Piece Standard: amzn.to/3xzhysO
Wheel Bearing Grease Red: amzn.to/3xvl5bt
Valvoline Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid: amzn.to/3mLxvH1
3M Assorted Grit Emery Cloth Sandpaper: amzn.to/3OcuP0W
Super Funnel: amzn.to/3xwBGvD
Valvoline, Dexron/Merc, 1 Gal: amzn.to/3xvnqTA
Oil Drain Pan: amzn.to/39mazer
0:00 - Introduction
0:39 - Lift Vehicle
1:53 - Torque converter
2:42 - Lift Transmission
5:31 - Lower Bell Housing Bolts
6:10 - Torque Converter Bolts
9:51 - Upper Bell Housing Bolts
13:27 - Vent Hose
13:45 - Neutral Safety Switch
14:22 - Shifter Linkage
14:43 - Oil Cooler Lines
15:14 - Electrical Harness
15:30 - Exhaust
17:29 - Trans Mount & Crossmember
20:10 - Drive Shaft
21:44 - Heat Shield
22:05 - Starter
24:53 - Battery
25:11 - Trans Fluid
27:44 - Outro
I bought a rebuild transmission but its leaking oil from the deepstick tube
Make sure that the rubber grommet did not get pushed into the pan and that the dipstick tube is seated all the way
How many ft lbs. Did you torque bell housing bolts
Edit, edit, edit, favck. Too much edition, doing not editon fucbk again.
I sincerely appreciate you guys, the tutorial was *chef's kiss* awesome. Keep kickin ass guys
Thanks!!
Nice Job, Thank you!!
Thanks! Please subscribe to our channel.
Its almost like you made this series of videos just in time for me to have bought this truck with a bad 3/4 band. its a 2010 but im sure its all pretty much the same, i just hope i get the right kit and dont get pneumonia dropping the thing out in the driveway here in michigan this time of year lol. thanks for vids to follow along with. makes me feel confident that i can handle the rebuild myself.
If you have some help, you should be able to remove the transmission in just a few hours. Then I hope you have a warm garage for the rebuild! Good luck, it's really not a difficult project, just take your time and enjoy the learning experience
Also, I got my kit from transmissionbench.com. You could also use rockauto.com or summitracing.com. If you have a local transmission parts supplier, that might even be better
I was thinking about grabbing one of these guys www.ebay.com/itm/4L60E-4L65E-4L70E-04-up-Master-Rebuild-Kit-Transmission-Overhaul-4L60-E-4L75E/202644117744 I do have a workshop with some propane heaters to rebuild the tranny in. Just gonna have to shovel snow when I go to take it in and out lol. I’m just making sure I get a kit that has the pistons in it, cause I figure if it’s not that check ball in the housing it’s gotta be the pistons that caused the 3/4 to go bad. Originally I hoped it was just a solenoid so I dropped the pan twice trying to fix it but now when I drive it I can tell it hits 3rd but there’s just a lot of rpm before you get any sort of pull feel out of the pedal then it just drops back into 2 when it gets around 4k
Sounds like you have it figured out. Sounds like the frictions and steels are toast. Definitely replace the pistons and verify the check ball doesn't leak. Also look into reaming out and replacing the AFL valve in the valve body. You should also replace the TCC valve, these wear out and 3-4 apply fluid pressure can be reduced increasing slippage and burnout of clutches. Sonnax and transgo make kits for these repairs.
@@dudewecanfixit I’m looking for some but most of what I’m seeing is for 97-99 and 2000-03
Thank you for the detailed video
Thank you for your feedback! Consider leaving a like and subscribe!
Great work on your video.
Thank you! Consider subscribing 😁
Dude, I’m gonna try it this weekend!
Awesome! You got this!
Great videos!! Hey I like your hammer! I bet that hammer is older than you guys haha. It's like every toolbox has a old tool from dad, grandpa etc. Keep up the great work !
Thanks! I collect antique tools from garage sales sometimes!
Awesome video. Here is some engagement appreciation.
Thanks!
Great video
Thanks
It’s been a minute. But i don’t remember doing my torque converter bolts like that. I remember everything was done with the trans out and bolted to the flex plate. Then put the trans on. 😳
Do you mean that you bolted the torque converter to the flex plate and then try to stab the transmission onto it? That sounds very difficult
The wife totally ruined / blew up the trans in my 2003 Tahoe 4x4. Going to get one from u pull u pay and follow your series - thanks for details
Good luck, you can do it!
Try to find a four-wheel-drive, or you may need to swap your tail housing with a 2wd model
I see your from the busted knuckle garage. Took me a while too to stop using my ratchet handle like that. Think it was slipping off a nut and punching a sharp edge crossmember that finally did it.
Yep, some habits die hard
Awsome Vid❗❗❗❗❗👍
Thanks!
Great video.
Glad you enjoyed it
great job!!!
Thanks
Thank you Brother.
You're most welcome
Idk if my trans dip stick tube bent but I had the hardest time putting it in. Took 2 hours trying to bend and put it in place finally got it.
Those tubes are an absolute pain in the butt, I’ve had to lower a transmission and raise it back into place with someone specifically guiding that tube LOL
I can’t get my dipstick to sit flush with the transmission pan. Is there supposed to be about an inch of slack ? Or is the tube supposed to be flush with pan?
Cool videos bro
Thanks!
Great sir
I've known people to fill up converter first with 6 to 7 quarts of oil first and then fill up with 5 quarts 2 while it's off and gradually add other 3 to prevent leaking from vent and more accurate measurement of the oil that is supposed to take.
That's one way to do it. It does make the torque converter much heavier during install though
Agree, but definitely if you have the hands you can give it a try. Nice DIY video. By far one of the best ones out there. Always had trouble taking off the lock out connections and the heat applied madr it much easier
Thanks!
Very nice video
Thanks!
Good show and tell
Thanks! Glad you enjoyed the video
When I pulled the Allison 1000 out from behind my LB7 in the street to replace the broken flexplate (with a SoCal diesel billet 1 piece), I just put the truck on 4 ramps to give me the height I needed to work under it. Driveshaft I just pulled out of the trans and bungeed off to the side out of the way instead of pulling the heavy ass 2 piece driveshaft out. Having the wheels off wouldn't have made it any easier for me, what would've made it easier is if the street were smooth so I could maneuver the trans jack around. Glad I don't live there anymore.
That sounds like quite the job. I once replaced a one ton rear end in a sandy parking lot in Albuquerque
@@dudewecanfixit only other issue besides the jack not rolling on the crappy street surface was the damn flexplate bolts that were installed by Zeus himself at the assembly plant, all 8 of them. I'm 6' 280 and had to use the handle from my floor jack as a cheater pipe to break them loose.
Did you have somebody pulling security while swapping that rear end? I hear ABQ ain't the safest place in the world, lol.
@@GrandPrix46 no, but I did gather odd pieces of lumber and wood from the parking lot to get the rear of my truck up high enough to get the axle out
You can get the top center bolt from the engine bay. Behind the back along the firewall. Where a distributor would have been located. Soooo much easier.
T
The easiest way!
Great to know!
Pro tip i don"t pour all 12 quarts in , even if everythingbis empty , i pour 2 or 3 in the torque convertor then slode it all together , add 3 or 4 more , start it for 3 minutes or less , add 4 more , then check it to see how many more it wants , pouring all 12 at one time will have it running out the overfill every time .😂
You are absolutely correct, and that is what happened to me!
Tanks brother
safety first guys! good job but you need to buy at least a few concrete blocks to protect your self while you be under the truck
I use over rated jack stands for safety. Watch at the beginning of the video how I purposefully push on the truck in every direction to make sure that it will not move and is safe to be under.
Watch from 1:15
Hi nice video my question is how did you clean out the tourq converter from all tha nasty and burd oil. Just by draining it or did you use some kind of solvent to remove all that fine metal particles
If you have debris in your system, it is definitely recommended to replace the torque converter.
love the attention to detail where are you guys from??
Thanks, were from Louisiana
love your videos...quick question is a 4l60E transmission from 2000 to 2005 2WD compatible with green connector and torque converter, neutral safety switch....thanks in advance
I'm not sure
Thanks!
I hope this helped you!
Good stuff
Thanks
Best video ever. Do you add oil in the torque converter before you install? I save over $2000 dollars just by looking at this video like 6 times. Thank you so much
Yes, I usually put a half quart of transmission fluid in the torque converter before install
So I just finished installing my rebuilt transmission in my 2001 Yukon 5.3 RWD. Do I need to hook up a scan tool and reteach, or am I good to go? The one that I pulled seems to have been a factory build, and the one that I installed is a different one that I upgraded some of the parts, both being 4L60Es.
There is no relearn procedure.
Just install it and make sure the fluid level is correct
When installing the bolts to the torque converter I noticed you had to rotate the flex plate which rotates the crankshaft. Will this mess with the engines timing? If so, what should be done before starting the vehicle? Thanks for a great video!
It doesn't affect the timing, no worries there.
Tks vídeo
Good video but in case you didnt know all those extensions change the torque value. All dependent on the length and material
They definitely do, but there's no way to get a torque wrench in there, so I usually add a couple ft/lbs.
nice video.... I was wondering what brand is that blue impact you are using?
Kobalt from Lowes
Nice video. Would you do anything differently if you did it again? I have a 05 4x4 Yukon 5.3L. 233,000 miles. Looking to get a used cheap broken 4L60/65/70 to rebuild with my teen as a DIY learning project. To have ready. I found a used one for $60, with nothing but Reverse working. Thanks!
I can't think of anything I would do different for a standard rebuild. There are upgrades available.
Simply Awesome, is this the same transmission for a 2005 yukon XL?
Yes
Thanks
Did you fill the torque converter with fluid first? Also how did you get those top bolts on the bell housing in?
I added a half quart before I installed the torque converter. Get the other bolts snug first and then let the jack down a little too get more access to the top bolts
You guys are awesome!! thanks for sharing. Any recommendations for where to purchase a rebuilt transmission?
Jasper, looking for some local places with good reviews
Is there a cover that goes over the inspection hole in the bellhousing where you where moving the torque converter with your finger? Or is the hole just open?
Thanks
There probably should be a cover lol
Good job guys!!!
Thanks