How to Install and Adjust 700R4 TV Cable | Curt's Corner at Monster Transmission
Вставка
- Опубліковано 17 чер 2013
- Monster Transmission Presents Curt's Corner as Curt goes over a Throttle Valve Cable(TV Cable) for a 700R4 Transmission. Curt covers everything from taking the cable out of the package to installing and adjusting The TV Cable on a 700R4 Transmission.
Items Shown:
700R4 Adjustable TV Cable
www.monstertransmission.com/70...
Throttle Cable Bracket
www.monstertransmission.com/20...
Holley Carburetor TV Cable Kit
www.monstertransmission.com/Ho...
Edelbrock Carburetor TV Cable Kit
www.monstertransmission.com/Ed...
If you have any questions, comments or would like to purchase a TV Cable give us a call at 1-800-708-0087
Or visit us online at: www.MonsterTrans.com - Авто та транспорт
The first part of this video is all I needed to watch. I couldn't figure out how to take the cable out of the packaging. Installing the cable and adjusting it properly was easy though.
Exactly why I like monster, not all about making but actually replies to all these great and common questions and helping everyone out.
Great video. Thanks so much for posting. I have an 84 Blazer 305/700R4 that is shifting way too late. Your video has given me the confidence to try an adjustment on my own. I’ll keep Monster in mind for any future transmission needs. Thanks again!
Great information got everything all set on my 57 chevy pickup except setting the tension for the detent cable and with your video I feel confident I can dial it in myself ...thank you for being thurough and giving good complete information
Hey curt! Nicely done. Much appreciated.
Awesome clear precise explanation of functionality ☝
Excellent! Finally an end to an unsolved mystery.
this video is by far the best one I had been fighting getting my tv cable into my transmission properly for a week or so and couldn’t figure it out never thought you put the seal in first thanks!
Glad it helped!
Tip: when doing the initial set by stepping on the throttle, make sure that you "un" trip the choke. Most carbs will not let the throttle fully extended until the choke is off. Meaning it wont be full throttle and that will throw the adjustment off.
Thank you for making the video Curt.
Best video out here for adjustments and installation. Thanks man
Glad it helped, Thank you!
Glad you guys are cammed up and making movies. I have been sick for a very long time therefore I havent been able to work and check out videos. Good job as usual. If I ever get down to Atlanta I will stop in and check out your operation. If it is OK Thanks for your tech advice and your valuable information.
Awesome instructions!!! Thank YOU
These guys are awesome. Keep up the good work.
+Howard Ellis-Marks Thanks!
Excellent Video! Thank you!
Great video helped me tremendously thank you
Thank you so much for the installation instructions. I gotta replace mine on my 90 c1500 as I've adjusted it to no avail, I shift at 28 mph.
Adjusting mine this weekend! My 700r4 holds first until about 30mph, but other than that it shifts fine. It almost skips second sometimes and goes right to 3rd. I’m it’s just the TV cable out of adjustment and I don’t need a trans refresh/synchro replacement.
I was hoping this video would include the works for a Throttle Body as well, not only for carburetors. In any case is a excellent video for many owners with the 700R4.
you just helped me so much. I know it's been up for a while but thanks for the vid!
Glad to hear it!
Now I understand how it works thanks
VERY HELPFUL . Thanks
Thanks Steve!
thanks for that very helpful.
Awesome video!!!
Thank you for your very clear and concise explanation. One question: When and how do you adjust the jam nut on the telescoping portion of the cable? Thank you.
Once u have it to the length needed snug it, but be careful not to over tighten or the cable will crimp.
Well done. Thank you so much ✝️👽♥️👍🙏
Buen vídeo amigo.... now I know what to do on my Chevy...!!! Thanks
¡Gracias! Glad we could help you out 🙂
well done.
thank u sir
Thanks so much for the video guys. Question, would it be possible to replace the TV cable seal without having to drop the pan and drain the transmission?
Yes actually you can
aswome video thank you very much
Very good video. I installed a new cable and it shifts a little hard but
good but will not kick down
If it will not kick down under load I would check the TV cable adjustment and ensure your 1-2 shift point is around 18-20MPH.
www.monstertransmission.com/700R4-2004R-Throttle-Valve-Cable-TV-Cable-Adjustment-Instructions_ep_62.html
thank you this was very helpful!
+TheBlkWarrior You're Welcome!
That was helpful
Question? At 10:13 of the video you say to remove the Holley Throttle Stud. I have a a factory holley variable venturi that came off a 1984 Mustang Gt. The throttle stud on my carburetor is made to not come off. Looks like its riveted in. What do I do?
The ‘84 Mustang GT came with an AOD transmission and will not need a corrector bracket. The geometry will be the same as a 700R4. Give us a call at 800-708-0087 for any more assistance R sanchez.
Thanks very much!!!!!!
Alvino Melgoza You're Welcome!
i have a 700r4 in my 55 chevy, and its not shifting into overdrive around 45-60mph by it self unless i manually do it. would that be a bad adjust to the TV cable?
Greetings! I have a TH350 in a 73 caprice classic. i decided to go with the 700r4 trans.. I know i will need to purchase the lockup kit from you guys, but what kit do i need for my edelbrock 650 carb?
Greetings! This kit will probably be best for your carburetor:
www.monstertransmission.com/Edelbrock-Carburetor-Throttle-Valve-Corrector_p_4881.html#.WlO8_N-nGUl
good education for me.. but Curt, can you give me any insight on a TV cable on a PowerGlide trany in '62 Pontiac Tempest? mine is missing and I have no clue if I'm in trouble with it not connected to the carb, or not! thanks
+Trish Guerra Thanks for checking in with us. You should have an older cast iron power glide. Even without the T.V. linkage the transmission will shift at the same time no matter how hard you press on the gas peddle. It can still be driven that way.
I want to put a 700r4 in an 01 ram do you have a bracket to make the tv cable work with the throttle plate on that setup?
One thing you may want to consider is trying a 4L60E instead, with a stand alone computer it will be better read your throttle position sensor. But if not, we have a couple options that could be solutions to your situation, if you give our tech support a call they will be glad to help you with that 800-708-0087.
So basically; you want it to shift 1st to 2nd gear @ 17-20 mph... is 19 mph the most preferred point of reference?
Thank you
Yes that is correct. You don't want to be shifting much earlier than 17 mph or later than 20 mph.
Will a tv cable work on a 4L60-E transmission?
No, the 4L60-E is electronic so it needs a controller to shift.
Do you have mounting hardware, throttle body bracket, and cable for the 1987-1991) gm rochester 2 bbl tbi that's on a 4.3 v6?
Thanks for the video. It helped a lot. :)
rag Doll We do offer a universal bracket that should work as well as an adjustable tv cable. Feel free to give our tech support a call and they'll be able to help you out. Here are the links.
www.monstertransmission.com/200-4R-700R4-Chrome-Throttle-Cable-Bracket_p_4896.html#.VT98YCFVhBc
www.monstertransmission.com/700R4-Adjustable-Throttle-Valve-TV-Detent-Cable_p_6132.html#.VT98tSFVhBc
Monster Transmission
Great! That's what I needed to know. :)
rag Doll You're Welcome
Having a hard time adjusting mine, shifting early. I have 4.56 gears and 33 inch tires, trying to adjust but thinking the 4.56 gears are not going to allow the MPH shift points you mention. Any advice on what would be acceptable shift points for 4.56 gears?
Also if shifting early do I adjust the gross adjustment tighter or the fine tuning? Thanks for any help!
It should be the same, but it really depends on your preference. We've heard of guys who prefer a 20, 30, 45 shift for 4.56 gears.
Can I use this cable and bracket kit on a tunnel ram?
1985 k5 blazer with 350... Sometimes trans shifts perfect, seems that after i drive it for a while has a problem going from first to second... sometimes even slips when cruising at about 40-45 mph... got a Holley carb... not surewhat size... could this be the TV cable, just bought the truck and it has a rebuilt trans...not sure the cables were connected using the proper hardware...sound right?
+Jerica Sittig Thanks Jerica for checking in with us. The cable on a 350 would be set up for passing gear only. The next step would be drop the pan and see how much debris is in the pan. It sounds like you have a internal problem in the transmission. If you have any further questions give us a call at 800-708-0087. Thanks
So what do you do with all the extra cable that is hanging from the attachment
You can just cut and crimp the extra cable.
I bought a TCI universal TV cable and it did not come with the full throttle spring. Is it still ok to use or do I have to get that spring?
Yes C K, it is still ok to use.
To install a new cable on the 700r4 do you have to remove the pan or can you simply pull the cable out and connect the new one?
No need to remove the pan, just disconnect and reconnect on the link arm in the TV cable port behind the servo cover. Refer to this video around 2:51.
does the passing gear cable have to be connected?
Yes you would want that to be connected as well.
Maybe get your opinion on Trans. 700r4. Trans works til it gets warmed up. Than all gears goes out. Turn vehicle off restart and trans works again for little while. Does it again, but works if you turn vehicle off and restart. Thanks. Rick H.
Check your fluid level, There are many other possibilities but start there. When you turn it off, the fluid drains back down until you run it more.
I have always heard that the TV cable was an issue on that transmission if it wasn't done just right it would not be good in the long (or short) run!
The tv cable adjustment is very important, too loose or tight and your transmission will not run as well as it can and eventually burn up.
I have a rochester quadrajet
and a 700 R4
I need the cable and any brackets required for the installation
Can you provide me with part # and how to order them
Thanks
These are the parts used in this video:
700R4 Adjustable TV Cable
www.monstertransmission.com/700R4-Adjustable-Throttle-Valve-TV-Detent-Cable_p_6132.html#.XEh6H1xKiUk
Throttle Cable Bracket
www.monstertransmission.com/200-4R-700R4-Chrome-Throttle-Cable-Bracket_p_4896.html#.XEh6LFxKiUk
Holley Carburetor TV Cable Kit
www.monstertransmission.com/Holley-Carburetor-TV-Cable-Corrector-Kit-for-GM-700R4-4L60-200C-200-4R-Ford-AOD_p_6237.html#.XEh6OFxKiUk
Edelbrock Carburetor TV Cable Kit
www.monstertransmission.com/Edelbrock-Carburetor-Throttle-Valve-Corrector_p_4881.html#.XEh6U1xKiUk
I got a dumb question! Wouldn't the rear end gearing have an impact on the 1-2 shift point? I would think a 456 rear gear would shift earlier than a 273 rear gear!! No?? please help! Also, if you are flooring it, wouldn't shift later , on any auto? Thanks!!
You are correct the rear gear ratio will have an effect on the shift points but you will be setting the Transmission to the new setting when you change out the rear gear ratio. So as long as you are shifting between 18-20 MPH for your 1-2 Shift Point everything else should fall in place if no internal or governor issues. Thank you for choosing Monster Transmissions.
How do I find out the part number and where to order the bracket for the 700r4 to quadrajet? Have a hard time finding the right part.
www.monstertransmission.com/200-4R-700R4-Chrome-Throttle-Cable-Bracket_p_4896.html#.XIFvGihKiUk
How to install it on a Diesel Engine like a Cummins 6 Bt, or s Chevy 6.2 / 6.5?
My cable busted right where it connects to the carburetor... does that mean i can't loosen the nut to extend more wire and reconnect? Do i have to buy a new cable again?
We recommend a new cable prevent any more possible breaks in the line and late hard shifts.
You can find our adjustable tv cable here : www.monstertransmission.com/700R4-Adjustable-Throttle-Valve-TV-Detent-Cable_p_6132.html#.Wfs3KWiPKUk
Does the rear gear ratio have an effect on the on the miles per hour shifting points?
Yes it will so if you change out your rear gear ratio we recommend to re set your Tv Cable and ensure your 1-2 shift point is between 18-20MPH. Thank you for choosing Monster Transmissions.
wish you would show me how to set this up on my 250 straight six with a Rochester one barrel , IT HAD A GRANNY LOW 4 SPEED . its in my 68 c10 2wd its got 30,000 original miles and top end was so low I bought a 1991 700r4 and now looking at the linkage im stumped its backwards. I may have to get a long cable and come at it from the front side .ANY HELP WOULD BE APPRICIATED ! LOVE YOUR VIDEO IT DOES HELP BUT IM STILL IN DEEP DOO DOO .
If you could send us a picture of your carb linkage we can advise you how to connect the TV cable. marketing@monstertrans.com
What kit do I need for a Rochester 2 barrel carb set up. I have the origin bracket that bolts to the intake.
www.monstertransmission.com/200-4R-700R4-Chrome-Throttle-Cable-Bracket_p_4896.html#.YL51fvlKiUk
I need to replace mine on my 1986 camaro carbureted 305/700r4. Is this something thats doable in my driveway?? Any tips would be greatly appreciated
Daniel Delgado Yes it is doable. Be sure to take your time and follow the video accordingly and you should be just fine. Thanks
What if you have a 350turbo with overdrive and it gets a electric to to the transmission on driveer side
They do not make the 350 with overdrive
This might be a dumb question for you, but I don't know so please forgive me. I just installed a B&M shift kit in my 700R4 transmission. My question is do I need to re adjust the TV cable after the kit was installed?
No you installing a new Shifter should not move or misadjust your TV Cable adjustment so you should be fine. I would just make sure that you are shifting from 1st to 2nd around 18-20MPH and adjust as needed.
How much do y’all charge to adjust the cable ?
If you give our Service Center a call at 352-678-6373 we can get your info and give you an estimate. We'd be happy to help you fix that.
Does this work on all transmissions... Thm 250c? To a Rochester
This wont work on the 250c. The 250c only has a kick down and it is regulated by vacuum pressure.
ALso, would you know if the later 4l60E transmission can work with the 1987-1991 chevy 4.3l v6 engines? (The cable kindof scares me would rather the tranny do it on its own.) :0
rag Doll Yes the 4L60E should bolt up. You will also need the electronics to run that transmission.
www.monstertransmission.com/Transmission-Controller-Compushift-Transmission-Control-System_p_6156.html#.VT-ATiFVhBc
Monster Transmission
Thanks monster transmission.. I'm still conducting the research before buying.. Its kind of scary and a lot of information and will need several adapters. One for the transmission to my spicer dana 20 t-case and motor mounts to the cj frame for the 4.3 engine.. I may need others so, need to keep researching.. Thanks for your response. Let me know if you ever have any "blem" or special prices for the th700r 4wd transmission.. (Decided the electric one won't work with my current tbi harness and ecm. ;)
rag Doll We work with hundreds of these models every month so our staff is extremely knowledgeable with the GM units. Give us a call at 800-708-0087 and a Client Care Specialist will be able to clear up ANY questions or concerns that you may have. We are currently running a 10% discount that will end today. So actually now is the ideal time to purchase. We do also offer a layaway program so you could take advantage of that as well. Thanks!
Can you help me? I've got a 1988 700r4 and I cant figure out what the 4 pin wiring connecter does, ive done an engine/tranny swap on a vehicle and i need to know how to wire it up.
Also, is there a way to connect the TV cable to a Edelbrock 1406 carb without the bracket?
You would needs the external 4th gear harness. This controls the lock up function. You will still need the corrector bracket for that carb setup.
Monster Transmission I've puchased the bracket and got my transmission working, it work great. However, I dont have TCC in 4th gear. I dropped my pan and the solenoid isnt even there. Interesting?
I just replaced my motor .. the transmission was not touched now my car doesn’t seem to want to shift.. just revs up a lot and have to let off gas and it shifts.. could this cable be my problem ?????? Help
Yes, the tv cable could be too tight and or the geometry could be off. If you have changed to a carb or upgraded carb you will need a corrector bracket. Also make sure you check governor and look for sticking.
My 700 has hard shifts. Is this due to the cable being too tight or bad cable?
Most likely your cable is out of adjustment. Loosen the adjustment then push your cable towards front of the vehicle 1/8". Then take it for a road test. Repeat until issue is resolved.
Thanks. Hope it fixes my problem
You say the 1st to 2nd gear shift should occur between 17-20 mph. Do you mean only at wide open throttle or under all driving conditions? That shift point seems a little late for regular street driving, but I also don't want to burn up my brand new transmission. Could you verify that please?
+Chris Wiseman That shift point is under mid to full pressure. If you have any further questions give us a call at 800-708-0087 and we'll get you taken care of. Thanks
do all cables have the extending feature? i used NAPA part and didnt have to use cable tie either. my bracket mounts to manifold near dizzy and is a different style, is this to far away from carb? It is at its fully extended ratchet setting and has Hard shifts but they are right on the speed mark so i didnt really worry about it being a fresh rebuild on my 700. the clip and stud are directly on my edelbrock 1405 linkage without that throw lever. Am i okay as long as the cable is binding or is this affecting 3rd and 4th WOT?? i am having power issues in those gears. Thanks for your video very helpful
The 700r4 will not allow 3-4 wot shift. It's fail safe, so you have to delete from the valve body. If you have any other questions Mckenzie, give us a call 800-708-0087.
can it fit in a 88 cutlass supreme classic
+Dravus Wilson What motor and transmission do you currently have? If you can give us a call at 800-708-0087 and we'll get all of your vehicle specs to ensure that this is the correct transmission for your application.
Is there a bracket kit fior a Rochester 2 barrel carb
www.monstertransmission.com/200-4R-700R4-Chrome-Throttle-Cable-Bracket_p_4896.html#.YL51fvlKiUk
Crap, It looks like my TV cable somehow got detached. Did I basically just destroy my 3-4 clutch pack?
If it is slipping in 3-4 then yes. Premature wear can happen if the T.V. cable is not adjusted correctly. Give us a call if you'd like some more help on this, 800-708-0087.
good info
Whats the part number on 700r4 cable
Our part number is ADJ-TV-700R4
You can also find it here: www.monstertransmission.com/700R4-Adjustable-Throttle-Valve-TV-Detent-Cable_p_6132.html#.X6VSWIhKiUk
mine is a 2.8 S10 and it is on the other side of the carburetor, is that normal?
It could be normal for that application
Myvtranny stopped downshifting. What could be wrong with it. Cable is alright as much as I can tell. It also don't have overdrive
hello... whats the differences between the passing gear of a th350 and a 700r4 tv cable.
The TH350 has 3 gears and the 700R4 has three gears and an overdrive, The transmission would just drop a gear for passing.
are the 700r4 and 4L60 (non electronic) the same trans?
Yes, Sort of :) The 4L60 came about in 1993. The main difference between is the 4L60 came with a 5 pin lockup harness vs a 4 pin. Size, looks and internals stayed consistent. Hope that helps, Thanks