LEDs are themselves directional so to get an LED to work for the turns you would have to modify the wiring to make one wire the signal power for left and right, second wire to chassis/ground. The paint trick is super cool though and much easier so I wish I would’ve thought of that 😂
Really saw I was onto something lol. The wiring harness comes to that point in which it inverts signal per side. Sending signal left or right. It works for me!!
hey brother i really appreciate all your navi content but i am having an issue with mine that im sure you have an answer too you briefly touched on in this video. so i did the ac / dc conversation, upgraded the flasher relay and currently have led headlight bulb, led front signals, led rear taillight from reckless customs with integrated turn signals and i also upgraded the speedo bulb to a bright white led. i tried installing an led bulb for the turn signal as well but ran into the same problem that you showed here in the video where it does not work only one side works and if you flip the bulb 180* then the other indicator side will work but not the previous one so yes can’t run an led bulb for the turn signal indicator and i’m fine with that however the problem i am having is that if i plug the stock indicator bulb back into the turn signal socket then when i hit the switch to activate either my left or right indicator all 4 of my actual turn signals all flash simultaneously. how do i fix that so that when i indicate left or right all 4 blinkers don’t hazzard flash with the stock turn signal indicator bulb in?. i have been trying to find videos on here or checking online forums and facebook groups but no luck so far it seems like yours are working perfectly fine so if you could help me please 🙏🏼
@@JayKing-tj2et so it sounds like you are missing resistors. I personally did resistors on each turn signal themself, but I have heard you only need them in the front. Resistors prevent back current from tracing all 4 turn signals in the harness. MNNTHBX website has them and I believe Yoshimura does as well. Look up “LED RESISTORS”. Hope this helps.
@@pookythomasmoto9147 i found your diode video after i had already left my previous comment and that’s what i ordered the same yoshimura one that you did that’s different from a resistor? i have an upgraded flasher relay and it says not to install resistors if running an aftermarket turn signal flasher relay so hopefully the yoshi diode fixes it all.
@@xCARPx2014 You are correct! So if you take off all 4 small Phillips screws and slowly pull the speedometer layout itself up (after removing the clear plastic cover) you will see a green filament and a blue filament. The bulbs are yellowish but the filament plastic cards dye them. The bulb is hard wired into the speedometer and is not able to be removed unfortunately. You can, but you will have to get quite creative.
Feed me all the Navi content you can!
Coming right up
Navi content 🙌
LEDs are themselves directional so to get an LED to work for the turns you would have to modify the wiring to make one wire the signal power for left and right, second wire to chassis/ground. The paint trick is super cool though and much easier so I wish I would’ve thought of that 😂
Really saw I was onto something lol. The wiring harness comes to that point in which it inverts signal per side. Sending signal left or right. It works for me!!
What about the highbeam indicator?
@@xCARPx2014 you have to switch around the wires that lead from it. Something like green to white and blue and the other to the opposite
hey brother i really appreciate all your navi content but i am having an issue with mine that im sure you have an answer too you briefly touched on in this video. so i did the ac / dc conversation, upgraded the flasher relay and currently have led headlight bulb, led front signals, led rear taillight from reckless customs with integrated turn signals and i also upgraded the speedo bulb to a bright white led. i tried installing an led bulb for the turn signal as well but ran into the same problem that you showed here in the video where it does not work only one side works and if you flip the bulb 180* then the other indicator side will work but not the previous one so yes can’t run an led bulb for the turn signal indicator and i’m fine with that however the problem i am having is that if i plug the stock indicator bulb back into the turn signal socket then when i hit the switch to activate either my left or right indicator all 4 of my actual turn signals all flash simultaneously. how do i fix that so that when i indicate left or right all 4 blinkers don’t hazzard flash with the stock turn signal indicator bulb in?. i have been trying to find videos on here or checking online forums and facebook groups but no luck so far it seems like yours are working perfectly fine so if you could help me please 🙏🏼
@@JayKing-tj2et so it sounds like you are missing resistors. I personally did resistors on each turn signal themself, but I have heard you only need them in the front. Resistors prevent back current from tracing all 4 turn signals in the harness. MNNTHBX website has them and I believe Yoshimura does as well. Look up “LED RESISTORS”. Hope this helps.
@@pookythomasmoto9147 i found your diode video after i had already left my previous comment and that’s what i ordered the same yoshimura one that you did that’s different from a resistor? i have an upgraded flasher relay and it says not to install resistors if running an aftermarket turn signal flasher relay so hopefully the yoshi diode fixes it all.
Hello ma,
Where did you get the LED signal kit? In the front and rear? Thank you!
Yoshimura turn signals. On their website or MNNTHBX, or SteadyGarage. Thanks!
Love ur video bro ! thanks
Which one is the high beam indicator bulb?
I can't seem to find it, unless it's under the white plastic.
@@xCARPx2014 You are correct! So if you take off all 4 small Phillips screws and slowly pull the speedometer layout itself up (after removing the clear plastic cover) you will see a green filament and a blue filament. The bulbs are yellowish but the filament plastic cards dye them. The bulb is hard wired into the speedometer and is not able to be removed unfortunately. You can, but you will have to get quite creative.
@@pookythomasmoto9147 damn, I wanted to have all blue LEDs in there lol.
Both! Honda anything.
Have you found a led or replacement bulb for the front headlight to make it brighter? That's my current issue
same here
Anything that is a H4 or around that fitting. XKGLOW sells a red anodized one that is powerful
where can i find those seats!
Hit up CheekySeats!
Stick to Navi stuff
Navi NAvi NAVi NVAI
All