How To Remove & Replace Board In Your Hot Tub(BALBOA VS PACK) TuffSpa TT650 (DIY Spa Repair)
Вставка
- Опубліковано 22 жов 2024
- DIY ..Removal & Replace board in your Hot Tub ..This is a step by step of how to replace the board in a hot tub that has a Balboa pack in it .. Its not a tough job and it should not take more then an hour to do.. Remember to turn off the power before you start and use a 1/4 and a 3/8 wrench to remove the heater.. For more Info Videos or advise you can call me at The Arizona Hot Tub Factory 623 842 4665 Thanks and I hope this Video helps You. Tuff Spa TT650
I bought a Balboa replacement board. No one would answer my questions about the dip switches. You did. In fact that Board you replaced is the very board I bought only set up for 110v.
Great video. The screw on my board that has a the paint on the head was in the bottom left. Just scraped out the paint with a small pick and used a quality screwdriver. I didn't have to remove the wires from the heater. I was able to just unplug the black plug on the board that is for these heater wires. The board cleared everything and was able to be removed. I also had a sub-board in front laying flat on top of the heater for additional motors. That I removed.
Good Job Spa Man, Your work needs an award. It helped with our 2007 Dim1 19' Aqua Swim Dual Spa and Hot tube rebuild. Working on an M-Class, spa side board failed and been avoiding it's R & R. Dim1 Products have limited YT vis for some reason.
Thanks will tackle this myself now. Wish you were closer to BC.
This is extremely useful. Please more videos!
More to come! Thanks for Watching & SUBSCRIBING
Great video. Just received my backorder board. After your instruction I feel confident I can manage this swap. Thanks!
Just spotted a possible cause of the heater connections burning up: the connection bolt on the circuit board has a nut Loctited in place -- and the Loctite got on top of the nut, which will make for a higher resistance connection.
Great Video Scott , Thanks .Scott
I am getting power to the hot tub. The top side is not getting power or coming on. So how do I check to see it it's a topside or bad board? Nothing inside the tub is getting power(pumps, heater, etc). So I don't know if it's a lack of power to the topside. Is there a place I can test for power inside the board after the line set? I've checked all fuses.
Check to make sure it is hooked up correctly and all connections are tight Proper wire size and type is very important also #6 THHN wire only (Not Romax ever)check all grounds and check with the breaker turned off the all connections in the pack are pushed in all the way check all fuses with a TESTER. if all that checks out and its a New tub call the dealer you bought it from If you bought it on line and the manufacture dropped shipped it to your door Im story to say LET THE FUN BEGIN and get ready for endless email and phone calls or you could bite the bullet and hire a spa tech to come out and figure it out and fix it for you. If you bought the spa used then like I just said call a spa tech and you with be good to go. Thanks for Watching & SUBSCRIBING
great video...I have a Jacuzzi J325 that needs a new board....same thing in regards to process????....I have no display and the tech said the circuit burned out to display
I have a circuit board that I'm unable to identify can you help me ?
thanks for sharing. I hope this fixes my problem
If you need help you can call Scott at the office and I sure he will get you going in the right direction.. Thanks for Watching & SUBSCRIBING
Great channel. I have balboa VS. Suddenly pump only runs on low. Any idea what it could be?
Check the pump and Motor.. Thanks for Watching & SUBSCRIBING
sr scott me puede decir cual puede ser la falla en un spa que demora mucho tiempo en calentar
Do you do services over the phone ? I have new vs500z i am having issues with
SUBSCRIBE to my channel...And give me a call and I'll try to Help
hi scot i from montreal i have a cliente who is looking for replacement off balboa mogher board EL8000 but i dont have om my stock is there any equivalent for it as i have El2000 or other balboa control systeme like BP or VS
Did you ever find a board ? I need to replace mine trying to source a new board
Even with the hot tub unplugged do I have to worry about being shocked? Looks like there are capacitors on that board.
I would say No..I have to say you are the first to ask me that and I can say I have never been shocked ever by a Hot Tub or Spa and I touch and test all over the board with the Breaker shut off and I have never been shocked... Hope that Helps Thanks for Watching & SUBSCRIBING
@@spaman5440 Thanks for the reply. I really appreciate your time!
Scott - great videos! This is Peter in Orlando, and you & I spoke 2 weeks ago about my Balboa Antigua Spa Dura SportAW. F6. Ec
: Model #: VS501Z. I confirmed its getting 120V and the board , and the topside control does not appear to be the problem. So I'm now guessing it's an issue with the board (6 years old). There's only 1 pump (which is working fine). Also, Balboa told me I could replace on my unit w/a 300VS board versus the 501Z (does that sound right?). Do you have any suggestions on where to go for for a quality & economical replacement circuit board? Amazon, local, other? Thanks.
My fuse didn't pop on my board so not only did it fry the board but melted the box.
would you happen to no wear I go to order a board for my Nordic hot tub
The sunglasses tell you this guy knows hot tubs
Thanks For Watching & SUBSCRIBING