Re index your chuck to its backplate. A lot of your runout or wobble is there. And lube everything WELL. Before you damage all those hard to find and expensive old bronze Busings, . You seem to be a fast learner. Cudos to you buddy
Adjust en oil the bearings of headstock first, your workpiece is jumping all around, but nice job bringing this rust to live again. some grease as wil do wonders for this nice lathe. succes
Sono un tornitore e vecchio restauratore, posso dirvi solo che avete fatto un ottimo video di come non si deve restaurare. Un tornio di questo genere non merita di essere trattato in questa maniera. Capisco che ci vuole molto tempo per fare questi lavori ma è meglio non iniziarli che rimanere a metà (eseguito correttamente sarebbe stato un piccolo gioiello)
@robertocentonze9653. Si es cierto que usted es tornero y restaurador de vete a saber no habla como un profesional, yo soy del mismo oficio, hace unos veinte años me regalaron un torno de edad similar a la del vídeo, le híce lo mismo que el autor de esta publicación, desmontaje completo del torno, limpieza a fondo de cada pieza, pintura, montaje, engrase y ajuste de la máquina, y nada que envidiar a tornos de última generación a la hora de tornear piezas de precisión. Usted en su respuesta se muestra de forma arrogante, y un profesional no tiene ese comportamiento que muestra usted. Usted se ha limitado a criticar el trabajo de esta publicación, pero no ha facilitado datos de como hacerlo correctamente, solo os gusta tocar las narices y criticar.
Looks like there is alot of play in the chuck. Did you get that sorted out if so I would like to know how you did it my old lathe has exact same problem
Nie wiem skąd tyle pozytywnych komentarzy. Nie zrobiłeś nic co by miało poprawić pracę tej tokarki. Dobrze, że nie odnawiasz starych samochodów. Wyglądałoby to tak, że byś go umył i pomalował wstrętnym jednym kolorem wszystko łącznie z kierownicą, wszystkimi przełącznikami i tapicerką. A rozklekotana skrzynia biegów, łyse opony i urwane lusterka zostałyby po staremu.
разобрать, почистить и покрасить, причём закрасив вместе с технологическими отверстиями - это не реставрация, это обслуживание))))) он наверняка работал бы и без разборки и чистки
To není full restoration, ale jen vyčištění a nastříkání. Neviděl jsem výměnu jediného dílu, žádné seřízení, ta univerzála se třepe jako drahý pes. Na výstavu dobré, ale na práci ne.
Just wondering why you didn’t repair the speed control lever as it was clearly broken? Cool old lathe but it looks like it could eat your hand for breakfast!
Comme toujours ce n’est pas une restauration mais un grand nettoyage et une Novelle peinture mais aucun grattage du banc et des coulisseaux des chariots!
A part un nettoyage à fond et une nouvelle peinture rien n'est fait pour améliorer l'état mécanique du tour , polissage des axes et remise en état des écrous de réglage de l'axe du mandrin .
Broken selector handle not repaired/replaced. Oil ports/cups not serviced.Tailstock not serviced/disasembled, etc... Cleaned and painted NOT a restoration.
Realmente muy pobre. Mecanicamente es una pieza de descarte y de restauracion no tuvo nada, no se verificaron centrados, alineaciones ni alabeos. Posiblemente sirva para tornear madera.
I'm surprised it came apart so easy. No oil in the apron gearbox ,table drive or variable speed for the chuck. No grease in the chuck either. You made a piece of junk work. Congratulations!
I am glad that the man washed and painted .Disassembled and assembled. But do not dream of any accuracy here. Really junk. In order to achieve some kind of correctness, his machine needs to be disassembled 10 more times, adjusted and reassembled. I can see how the part shakes when grinding, how the cartridge shakes. It's not that about hundredths of a millimeter, but it's too early to dream about tenths.. 43:23
Он плохой специалист. Даже покраску сделал неправильно. Разобрал, помыл, замену износившихся деталей не произвел, не восстановил. Покрасил как попало и собрал и все. Работать станок как положено не будет, оно и видно. Гремит, стучит, вибрирует.. Может он стоять в музее будет.
Non é un buon restauro. La verniciatura é eseguita male ..la pulizia degli ingranaggi non é stata accurata così come le bronzine e le leve dei comandi e i volani della torretta e del carrello non si verniciano mai ma si spazzolano e si lucidano così come vite e bullone e dadi ...potete migliorare ...siate fiduciosi ! Buon lavoro 😊
good job just check the spindle bearings are bronze
thank you
Не бит, не крашен, с огромными люфтами!!!
😁😅😂🤣
43:10 That's not even vibration, it's an earthquake ha ha ha It gives the impression that the part is going to jump out of the lathe.
Re index your chuck to its backplate. A lot of your runout or wobble is there. And lube everything WELL. Before you damage all those hard to find and expensive old bronze Busings, . You seem to be a fast learner. Cudos to you buddy
Adjust en oil the bearings of headstock first, your workpiece is jumping all around, but nice job bringing this rust to live again.
some grease as wil do wonders for this nice lathe. succes
All that work, yet you never removed the back-plate from the spindle nose! Why not?
Wakodahatchee Chris
I'm still curious.
very nice ...💫💫💫
thank you
I really enjoyed this video. It looked like it took awhile to rebuild. Thanks for sharing this video. Looking forward to your next project.
Cleaner than it was,,, can't say it sounds all that tight though.
Yeah it had more chatter than a bus load of old ladies on a day trip ! The test piece wasn't even running true....
Sono un tornitore e vecchio restauratore, posso dirvi solo che avete fatto un ottimo video di come non si deve restaurare. Un tornio di questo genere non merita di essere trattato in questa maniera. Capisco che ci vuole molto tempo per fare questi lavori ma è meglio non iniziarli che rimanere a metà (eseguito correttamente sarebbe stato un piccolo gioiello)
@robertocentonze9653. Si es cierto que usted es tornero y restaurador de vete a saber no habla como un profesional, yo soy del mismo oficio, hace unos veinte años me regalaron un torno de edad similar a la del vídeo, le híce lo mismo que el autor de esta publicación, desmontaje completo del torno, limpieza a fondo de cada pieza, pintura, montaje, engrase y ajuste de la máquina, y nada que envidiar a tornos de última generación a la hora de tornear piezas de precisión.
Usted en su respuesta se muestra de forma arrogante, y un profesional no tiene ese comportamiento que muestra usted.
Usted se ha limitado a criticar el trabajo de esta publicación, pero no ha facilitado datos de como hacerlo correctamente, solo os gusta tocar las narices y criticar.
Total destruction of the lathe. They don't really understand about measurement and accuracy. Main spindle destroid
needs a little more adjustments, but good work. Respect.
Main forward spindle (chuck) bearing seems like it's toast?
Mio amico che bel ricordo
Maybe installing ball bearings might make it run smooth again 🤔
in realtà le bronzine di quel tempo, se registrate bene funzionavano meglio dei cuscinetti (silenziose e più durature)
Less painting the gasket surface next time.
Limpieza , pintura y lubricación de torno.
Ermoso regalo
Looks like there is alot of play in the chuck. Did you get that sorted out if so I would like to know how you did it my old lathe has exact same problem
Nie wiem skąd tyle pozytywnych komentarzy. Nie zrobiłeś nic co by miało poprawić pracę tej tokarki. Dobrze, że nie odnawiasz starych samochodów. Wyglądałoby to tak, że byś go umył i pomalował wstrętnym jednym kolorem wszystko łącznie z kierownicą, wszystkimi przełącznikami i tapicerką. A rozklekotana skrzynia biegów, łyse opony i urwane lusterka zostałyby po staremu.
разобрать, почистить и покрасить, причём закрасив вместе с технологическими отверстиями - это не реставрация, это обслуживание))))) он наверняка работал бы и без разборки и чистки
Acho quer voce nao marcou a possiçao do flange da praca po isso esse tombo
Có máy nào ko a
có nhé
is all this vibration and noise normal?
Muito bom parabéns amigo 👍
Hi there. Is there a reason why you don't apply a primer before final color spray
muy buen trabajo. gracias por el video.
Muito bom🤓👍🇧🇷
Lau dầu, tút tát xong chắc để trưng bày thôi, chứ con này mà tiện thì sản phẩm ra hàng đồng nát luôn. 😂
GREAT JOB SIR !!!
To není full restoration, ale jen vyčištění a nastříkání. Neviděl jsem výměnu jediného dílu, žádné seřízení, ta univerzála se třepe jako drahý pes.
Na výstavu dobré, ale na práci ne.
Очень классно!!!
another great re build how do you remember where all the bits go you have a great head on your shoulders awesome
Adoro este canal
Just wondering why you didn’t repair the speed control lever as it was clearly broken? Cool old lathe but it looks like it could eat your hand for breakfast!
Of course not
Your Main shaft bushings are Bad, Its shaft in bounsing up and down
It wasn't bouncing, it was using morse code to tell us to take it to the scrapyard and put it out of it's misery, lol.
Estaría bueno si repararias lo dañado
Very cool.😊
Parabens .pelo seu trabalho
Good job 👍👍👍Thank you for sharing. Be safe 🇨🇦
thank you very muck
Comme toujours ce n’est pas une restauration mais un grand nettoyage et une Novelle peinture mais aucun grattage du banc et des coulisseaux des chariots!
Super cool
tiện nhảy như máy đầm cóc thế thì lmj dc.
This is not a restoration. This is cleaning and painting.
yeah, but BADLY.....
W dodatku wstrętnym kolorem.
A part un nettoyage à fond et une nouvelle peinture rien n'est fait pour améliorer l'état mécanique du tour , polissage des axes et remise en état des écrous de réglage de l'axe du mandrin .
This lathe feels like it can only be displayed, and the test run has no precision.
❤
😅😅😅😅😅 you need to get Reed of all of the old paint. You just did an have as. Job
Молодец. Удачи.
В чем? В мойке?
@@АЛЕКСЕЙ74-ь6о Ну что ж поделать, раз мойка первое дело при ремонте.
@@СергейПономарев-в7ь а я дурак думал, что первое это хотя бы смена подшипников, а то не вооружённым взглядом видно как разбит шпиндельный подшипник.
@@АЛЕКСЕЙ74-ь6о там ВСЁ разбито, и НИКАКИХ мер по устранению люфтов не было сделано.
Ez nem felújítás. Csak Tisztítás+ festés. A tokmány rögzítésétől a főorsóig katasztrófa. stb.
Broken selector handle not repaired/replaced. Oil ports/cups not serviced.Tailstock not serviced/disasembled, etc... Cleaned and painted NOT a restoration.
Realmente muy pobre. Mecanicamente es una pieza de descarte y de restauracion no tuvo nada, no se verificaron centrados, alineaciones ni alabeos. Posiblemente sirva para tornear madera.
Così come è ora può tornire appena il legno...
the video is fun, however the work is very bad.
I'm surprised it came apart so easy. No oil in the apron gearbox ,table drive or variable speed for the chuck. No grease in the chuck either. You made a piece of junk work. Congratulations!
I am glad that the man washed and painted .Disassembled and assembled. But do not dream of any accuracy here. Really junk. In order to achieve some kind of correctness, his machine needs to be disassembled 10 more times, adjusted and reassembled.
I can see how the part shakes when grinding, how the cartridge shakes. It's not that about hundredths of a millimeter, but it's too early to dream about tenths.. 43:23
.
..0! .q,0. ..........ñm,oq..a
.
Он плохой специалист. Даже покраску сделал неправильно. Разобрал, помыл, замену износившихся деталей не произвел, не восстановил. Покрасил как попало и собрал и все. Работать станок как положено не будет, оно и видно. Гремит, стучит, вибрирует.. Может он стоять в музее будет.
Я так понял поверка, настройка и замена подшипников не главное ) главное - покрасить без грунтовки 😊
@@ogenmiller да там даже подшипников нет нигде
COOL!!!!!
Каждый зарабатывает как может. В том числе и на лайках. Не бейте музыканта он играет как может не зная токарных нот, от слова совсем.
Total failure was not a smooth cut. Jumping everywhere no precision at all.
Yeah that clampy spinning thing needs a bearing or a new shaft or something.
My shop class senses are like tingling…
this is not repaired lathe
Holy crap! What a piece of crap. Mad skills pulling it apart and cleaning though.
𝙥𝙧𝙤𝙢𝙤𝙨𝙢 🙌
certo che none un bel lavoro potevi fare di meglio molto meglio
Ce n'est vraiment pas ce que l'on appelle une révision de tour . c'est du tout petit bricolage au mauvais sens du terme !!
Non é un buon restauro. La verniciatura é eseguita male ..la pulizia degli ingranaggi non é stata accurata così come le bronzine e le leve dei comandi e i volani della torretta e del carrello non si verniciano mai ma si spazzolano e si lucidano così come vite e bullone e dadi ...potete migliorare ...siate fiduciosi ! Buon lavoro 😊
Отнеси обратно на металлолом
A half-assed restoration. Soon to be a piece of junk again!
понты , а работать нельзя...
Restaurare cu tesla de scos cuie nu prea seamana a restarare Nici macar pregatirea ptru un muzeu Sa fim serios asta e restaurare? 😅😅😂😂😂😂😅😅😊
ипать там биения везде где только можно, никакой жёсткости... это уже металлолом.
Dài dòng,màu mè! restoration như cục sick!!!!