How To Replace Driver Side CV Axle 2007-2012 Nissan Sentra
Вставка
- Опубліковано 21 жов 2024
- Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ia/1AAC...
A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications. This video shows you how to install one in your 2007-2012 Nissan Sentra.
• Check here for more videos on the 2007-2012 Nissan Sentra • Nissan Sentra 2007-2012
This process should be similar on the following vehicles:
2007 Nissan Sentra
2008 Nissan Sentra
2009 Nissan Sentra
2010 Nissan Sentra
2011 Nissan Sentra
2012 Nissan Sentra
Tools you will need:
• Pry Bar 1aau.to/ofX/1AX...
• 21mm wrench
• 21mm Socket 1aau.to/ojk/1AX...
• 32mm Socket 1aau.to/oJ/1AAS...
• Pliers
• Side Cutters
• Torque Wrench 1aau.to/onT/1AX...
• Center Punch 1aau.to/oba/1AX...
• Hammer 1aau.to/ofV/1AX...
• Rubber Mallet 1aau.to/oan/1AX...
Subscribe: / @trq
Check out our playlist:
Nissan Sentra 2007-2012: • Nissan Sentra 2007-2012
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
I like the five lug to 4 lug conversion at 0:20
thank you for showing. I was told if they are bad the car would shake at high acceleration. is that true? I had the alignment done, but still did not work well. still shaking. this car has those new shocks and now new axles. good to see car being taken care well.
Oh nice a 7 minute job…. 7 days later . All done ✅
Thanks for the video! Did you have to top off the trans fluid after? Mine has the CVT. Thanks!
How on earth did you pull that CV joint out of the transmission so easily?
Presente en clases de mecánica automotriz en TRQ, mirando en Navojoa Sonora México, gracias por compartir información que ayuda 🎉
I WANTED TO SEE THE INNER PART THAT GOES INTO TRANSMISSION, IS THERE A MEDAL RING, NO AXEL SEAL NEEDED?
Can you use a different anti seize
on the spline or does it have to be copper never seize
Is there supposed to be a gap between the cv axle and the transmission or does it go right against it ?
Would this be the same on a 2016 Nissan Sentra?
Wheres the video for the passenger side?
You don’t have to remove link stabilizer like maxima and Altima?
What happens if some of all transmission fluid, spills out, do I have to replace transmission fluid
Yes, after the job, check the level of Transmission fluid and complet with the amount necessary
Do you need to lube the spline that goes inside the transmission?
What if I try to take off the cv axle bolt and the whole cv axles spins with the wrench?
Would this be the same process on a manual 2007 nissan sentra 2.0?
The Axle Nut needs to be removed before rasing the front of the vehicle or somebody needs to press and hold the brakes, which might not be eficient and safe and might damage the transmission.. grounded and parked vehicle with hand brakes on worked for me..
Old boy works as fast as he talks. Red thread locker? Cheers!
+David M Thanks for the feedback! 1aau.to/m/Shop-TRQ
Why do some have ABS ring? Is that required for cars with ABS?
The ring is required for ABS. If you don't have ABS and it doesn't interfere with installation you can just keep it on.
No one shows putting the fluid back in
Can this be done with hand tools?
Yes
Yes, but you will need at least a 1/2" breaker bar and quite possibly a "cheater" (a pipe to extend the bar) in order to remove the axle nut. Soak it good with PB Blaster or WD40 first.
Yeh right.these Nissans are a joke.it is not that easy pulling the axle out.im still fighting it.i guess I'm gonna have to buy one of those cv puller tools. These videos always make it seem so easy.
This shouldn't change the alignment though